SPL2FXX SIEMENS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

  • Efficient radiation source for pulsed and cw-operation
  • Reliable InGa(Al)As strained quantum-well material
  • Small TO-220 package with efficient thermal coupling
  • Includes thermistor to control temperature/wavelength
  • Single emitting area 200 µm × 1 µm
  • FC-type connector for efficient fiber coupling

Applications

  • Pumping solid state lasers (Nd: YAG, Yb: YAG, …)
  • Medical applications
  • Laser soldering
  • Energy transmission
  • Testing and measuring applications Type Old Type (as of Oct. 1996) Wavelength Ordering Code SPL 2F81 SPL 2F85 SPL 2F94 SFH 487406 SFH 487426 SFH 487446 808 nm 850 nm 940 nm Q62702-P368 Q62702-P1678 Q62702-P1631 *) Other wavelengths in the range of 780 nm ... 980 nm are available on request. Maximum Ratings (TA = 25 °C) Parameter Symbol Values Unit min. typ. max. Output power (continuous wave) 1) Popt – – 0.8 W Output power (quasi-continuous wave) 1) (tp ≤ 150 µs, duty cycle ≤ 1% ) Pqcw – – 1.1 W Reverse voltage VR ––3V Operating temperature Top – 10 … + 60 °C Storage temperature Tstg – 40 … + 70 °C Maximum soldering temperature, max. 5 sTs – – 250 °C 1) Optical data refer to output after a fiber of 5 m length (core ∅ 125 µm, 0.35 NA, attn. 8 db/km)

(SFH 4874x6) Semiconductor Group 2 Diode Characteristics (TA = 25 °C) Parameter Symbol Values Unit min. typ. max. Emission wavelength 1) λpeak 803 840 935 808 850 940 813 860 945 nm Spectral width (FWHM) 1) Δλ 2n m Output power 2) Popt 0.75 W Differential efficiency 2) 808 nm 850 nm 940 nm η 0.60 0.60 0.55 0.70 0.70 0.60 0.85 0.80 0.70 W/A Threshold current 808 nm 850 nm 940 nm I th 0.40 0.30 0.30 0.45 0.40 0.35 0.55 0.50 0.40 A Operating current 1) 808 nm 850 nm 940 nm I op 1.3 1.3 1.4 1.5 1.5 1.6 1.8 1.8 1.8 A Operating voltage 1) Vop 2.0 V Differential series resistance rs 0.2 0.4 Ω Characteristic temperature (threshold) 3) T0 150 K Temperature coefficient of current ∂Iop/ ∂T 0.5 %/K Temperature coefficient of wavelength 4) ∂λ / ∂T 0.25 0.27 0.30 nm/K Thermal resistance (junction → heat sink) Rth JA 10 K/W 1) Standard operating conditions refer to 0.75 W after 5 m of fiber (core ∅ 125 µm, 0.35 NA, attn. 8 db/km) 2) Optical power measurements refer to output from fiber 3) Model for the thermal behavior of threshold current: Ith(T2) = Ith(T1) × exp(T2 – T1)/T0 4) Depending on emission wavelength NTC Thermistor Parameter Symbol Typ. Values Unit Resistance at room temperature (25 °C)RNTC 10 k Ω

(SFH 4874x6) Semiconductor Group 3 Optical Characteristics (TA = 25 °C) Radiant Power Popt vs IF Mode Spectrum Irel vs λ (Popt = 1.0 W) NTC Thermistor R T = f(TA ) RT 25 °C = 10 kΩ ± 1%

(SFH 4874x6) Semiconductor Group 4 Notes for Operation 1. Eye Protection This laser is a Class 4 Laser product. Refer to the relevant safety regulations for protection during handling and operation. 2. Overload Protection The specified values are valid as long as the diode has not been not overloaded. Voltage spikes from the power supply unit, even when applied for nanoseconds only, may cause irre- versible damage to the laser diode. Such spikes may occur when the power supply is turned on or off, or they may reach the laser diode from the line via the coupling capacitance of electronically controlled devices. The power supply should therefore be provided with appropriate protection circuits. Handling Notes 1. Package To avoid electrostatic damage it is recommended to observe the same rules as for handling MOS-devices. 2. Mechanical Attachment 2.1 Mounting hole (suitable for M 2.5) Because of the good thermal conductivity of the TO 220 base plate (copper) the heat loss is properly dissipated even if the component is attached on one side only. Some mounting techniques are shown below (Fig. 1 – 3). 2.2 For exact positioning of the TO component and other parts, e.g. lenses, the TO 220 package can be attached with appropriate clamping devices or screws (max. M 2.5). 3. Soldering When soldering the TO base to a heat sink, do not exceed the following limits:

  • max. soldering temperature: 125 °C
  • max. soldering time: 1 min.

(SFH 4874x6) Semiconductor Group 6 Package Outlines (Dimensions in mm, unless specified).