SP693A SIPEX | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 7
Technical content
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation The SP691A/693A Evaluation Board is designed to help analyze the many functions of the SP691A/693A µP Supervisory circuit. The evaluation board provides easy probe access points to all SP691A/693A pins so that the user can measure electrical characteristics and waveforms of each signal. The SP691A/693A Evaluation Board also provides solder pads for DIP or SOIC packages, as well as options for DIP or SOIC sockets for easy evaluation of multiple devices. The next two sections describe the SP691A/693A Board Layout and Using the SP691A/ 693A Evaluation Boards. A table of SP691A/693A Pin Assignments is also included with a section on Power Supply Connections. A SP691A/693A Evaluation Board List of Materials is provided with some manufacturers part numbers to use as a reference. Finally, a schematic is included of the SP691A/693A Evaluation Board.
DESCRIPTION
SP691A/693A Microprocessor Supervisory Circuit n Probe Points Accessible for all SP691A/693A Pins & Input Options n 16 Pin Narrow SOIC or DIP Sockets Available for the SP691A/693A Circuit n Pin compatible upgrade to MAX691A, 693A, 800L, 800M SP691A/693A Evaluation Board Manual
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation BOARD LAYOUT The SP691A/693A Evaluation Board has been designed to easily and conveniently provide access to all pins of the SP691A/693A device under test. Position the board with the silkscreen lettering upright (also see drawing on the front page of this manual) and you will see two vertical rows of eight pins each, which represent the 16 pins of the SP691A/693A device starting in the top left with V BATT as pin one. The pin receptacles are raised female pins which can accommodate easy-hook connection leads for power and meter connections, as well as scope probe hooks and grounds for waveform measurements. The 16 pin SP691A/693A may be installed in one of 3 locations: U1 for DIP or DIP sockets, U3 for SOICs or U2 for SOIC sockets. The five input pins for the SP691A/693A are provided with extra Input Probe Points for connecting inputs to these pins. For example pin 11 WDI has nearby pins V OUT and GND to connect to for evaluation of WDI timeout. These female receptacle pins can be jumpered together with easy-hook connectors or stripped back solid wire leads. In the case of inputs OSC IN, OSC SEL or PFI, a resistor or capacitor with leads may be pushed into the female receptacle pins to make easy connections. Also, mating male pins (see List of Materials) may be soldered to the components and inserted into the receptacle pins. USING THE EVALUATION BOARD Connect the SP691A/693A Evaluation Board to the power supplies for VCC and V BATT (see the section Power Supply Connections following the table SP691A/693A Pin Assignments). It is good practice to not switch power on until power connections are made to the evaluation board. Evaluating Pin Functions Pin 1 – V BATT – Backup-Battery Input. Connect to external supply, battery or capacitor and charging circuit. If this pin is not used, connect to GND. Pin 2 – VOUT – Output Supply V oltage. This function is used to provide power supply switching of either V CC or V BATT to an external device like a CMOS RAM to ensure a constant supply for the memory. To evaluate this function, vary the V CC voltage for a set VBATT voltage until you simulate the following conditions: V OUT connects to VCC when V CC is greater than VBATT and VCC is above the reset threshold. When VCC falls below VBATT and VCC is below the reset threshold, VOUT connects to V BATT . Start with VBATT voltage of about 2.8 to 4.0V and vary VCC from 0V to 5V to 0V and observe V OUT . (Note: a 0.1 µ F bypass capacitor (C1) is connected from VOUT to GND). Connect VOUT to VCC if no backup battery is used. Pin 3 – VCC – Input Supply V oltage - +5V input. A 0.1(F bypass capacitor (C2) is connected from VCC to GND. Pin 4 – GND – Ground reference for all signals. Pin 5 – BATT ON – Battery On Output. Goes high when V OUT switches to VBA TT . Goes low when V OUT switches to VCC . Connect the base of a PNP through a current-limiting resistor to BATT ON for V OUT current requirements greater than 250mA. Pin 6 - LOWLINE - LOWLINE Output goes low when VCC falls below the reset threshold. It returns high as soon as VCC rises above the reset threshold. The output can be used to generate a NMI (non-maskable interrupt) if the unregulated supply is inaccessible.
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation Pin 7 – OSC IN – External Oscillator Input. When OSC SEL is unconnected or driven high, a 10µA pull-up connects from V OUT to OSC IN, the internal oscillator sets the reset and watchdog timeout periods, and OSC IN selects between fast and slow watchdog timeout periods. When OSC SEL is driven low, the reset and watchdog timeout periods may be set either by a capacitor from OSC IN to ground or by an external clock at OSC IN. Pin 8 – OSC SEL – Oscillator Select. When OSC SEL is unconnected or driven high, the internal oscillator sets the reset and watchdog timeout periods. When OSC SEL is low, the external oscillator input (OSC IN) is enabled. OSC SEL has a 10µA pull-up. Pin 9 – PFI – Power-Fail Input. This is the non-inverting input to the power-fail comparator. When PFI is less than 1.25V , PFO_N goes low. Connect PFI to GND or VOUT when not used. Connect external divider R1 & R2 to Probe Pins and connect Unregulated V oltage to UNREG for Power Fail monitoring. Pin 10 – PFO – Power-Fail Output. This is the output of the power-fail comparator. PFO, goes low when PFI is less than 1.25V . This is an uncommitted comparator, and has no effect on any other internal circuitry. Pin 11 – WDI – Watchdog Input. WDI is a three-level input. If WDI remains either high or low for longer than the watchdog timeout period, WDO goes low and reset is asserted for the reset timeout period. WDO remains low until the next transition at WDI. Leaving WDI unconnected disables the watchdog function. WDI connects to an internal voltage divider between V OUT and GND, which sets it to mid-supply when left unconnected. For a simple check of watchdog function, connect WDI to either Probe pins GND or VOUT to cause WDO to go to a Logic Low. Pin 12 – CE OUT – Chip-Enable Output. The Chip-Enable (CE) function CE OUT provides internal gating of chip enable signals to prevent erroneous data from corrupting the CMOS RAM in the event of a power failure. During normal operation, the CE gate is enabled and all CE transitions are passed from CE IN to CE OUT. When Reset is asserted, this path is disabled. Note that CE OUT goes low (active) only when CE IN is low and V CC is above the reset threshold. If CE IN is low when reset is asserted, CE OUT will stay low for 12µs or until CE IN goes high, whichever occurs first. Pin 13 – CE IN – Chip-Enable Input. The Input to chip-enable gating circuit. Connect to GND or V OUT if not used. Pin 14 –WDO – Watchdog Output. WDO goes low and reset is asserted if WDI remains either high or low longer than the watchdog timeout period. WDO returns high on the next transition at WDI. WDO remains high if WDI is unconnected. WDO is also high when RESET is asserted. Pin 15 – RESET – RESET output goes low whenever V CC falls below the reset threshold. RESET will remain low for 200ms (when internal oscillator is used) after V CC crosses the reset threshold on power-up. Pin 16 – RESET – RESET Output goes high whenever VCC falls below the reset threshold. RESET is open drain and is the inverse of RESET. Note: To accurately measure the extremely small supply current in Battery Back-up mode, you need to cut split pads SP1 & SP2 (solder side of board) severing connections to C1 & C2 which would have leakage currents in the measurement range. Also, remove charging circuit components CBATT and D1 if they are installed.
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation Pin # Pin Name Pin Function Active Level Input Pin Points 1V BATT Backup-Battery Input NA 2V OUT Output Supply Voltage NA 3V CC Input Supply Voltage NA
4 GND Ground for all Signals NA
5 BATT ON Battery On Output HIGH
6 LOWLINE Lowline Output LOW
7 OSC IN Oscillator Input NA V
OUT & GND
8 OSC SEL Oscillator Select NA V OUT & GND
9 PFI Power-Fail Input HIGH R1 & R2
10 PFO Power-Fail Output LOW
11 WDI Watchdog Input Transitions V OUT & GND
12 CE OUT Chip-Enable Output LOW
13 CE IN Chip-Enable Input LOW V OUT & GND
14 WDO Watchdog Output LOW
15 RESET RESET Output LOW
16 RESET RESET Output HIGH
SP691A/693A Pin Assignments Power Supply Connections Pin 3 – VCC – connect to external +5 VDC supply. Pin 1 – VBA TT – connect to external V+ supply of 2.8 to 4.0 VDC, or install capacitor CBATT and charging diode D1 (see List of Materials). Pin 4 – GND – connect to negative or ground of +5VDC supply and ground of V+ supply for V BATT Note: Ensure VCC , VBATT and GND connections are made before operating device.
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation Component Part Number Manufacturer Ref. Des. Qty. µP Supervisor IC SP691ACN Sipex U3 1 Pin Receptacle-Female 300-1150-1472-7040 Mil-Max Mfg. 26 Ceramic Capacitor 0.1µF Generic C1, 2 2 Al. Spacers - 0.5" 8414 Keystone Elec. 4 6-32 Hex Nut Generic 4 Optional:
16 Pin DIP Socket 216-3340-00-0602 3M-Textool U1 1
16 Pin SOIC Socket 216-7383-55-1902 3M-Textool U2 1
Maxcap 1F 5.5V LC055105A Cesiwid Inc. CBATT 1 Signal Diode Generic D1 1 Pin Receptacle-Male 3137-3002-10-0080 Mill-Max Mfg. 26 SP691A/693A Evaluation Board List of Materials
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation SP691A/693A Evaluation Board Schematic
SP691AEB/03 SP691A/693A Evaluation Board Manual © Copyright 2000 Sipex Corporation Model Package
ORDERING INFORMATION
SIGNAL PROCESSING EXCELLENCE Sipex Corporation reserves the right to make changes to any products described herein. Sipex does not assume any liability arising out of the application or use of any product or circuit described hereing; neither does it convey any license under its patent rights nor the rights of others. Sipex Corporation Headquarters and Sales Office
22 Linnell Circle
Billerica, MA 01821 TEL: (978) 667-8700 FAX: (978) 670-9001 e-mail: sales@sipex.com Sales Office
233 South Hillview Drive
Milpitas, CA 95035 TEL: (408) 934-7500 FAX: (408) 935-7600