SMM400PD21

SMM400PS03-C XPPOWER | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

400 Watts

• Industrial, IT & Medical Approvals
• Low Profile for 1U Applications
• Optional Current Share & AC Fail
• Output Voltages from 3.3 V to 54 V
• Enclosed with Internal Fan & U-Channel Versions
• Class B Conducted Emissions
• Optional Molex Connectors SMM Series Input Input Voltage • 90-264 VAC (120-370 VDC) Input Frequency • 47-63 Hz Input Current • 6.35 A at 90 VAC, full load Inrush Current • 35 A peak max (cold start at 240 VAC & full load) Power Factor • Meets EN61000-3-2 Earth Leakage Current • <300 µA max at 264 VAC/60 Hz UVLO • Shut down when 75 VAC <Vin <85 VAC & turns on when Vin >86 VAC Input Protection • Internal 8 A fuse in line and neutral Output Output Voltage • 3.3 to 54 VDC - see tables Output Voltage Trim • ±5% on V1, adjustable by user Initial Set Accuracy • Within 1% of stated output voltage Minimum Load • Single output: 1%, Dual output (V1): 10% Start Up Delay • 2 s max at 120 VAC Hold Up Time • 20 ms min at 80% full load Line Regulation • 0.5% Load Regulation • ±1% (single outputs), ±3% V1, ±7% V2 (dual outputs) Over/Undershoot • Not to exceed 5% of nominal voltage Transient Response • 5% max deviation, recovery to within 1% in 500 µs for a 50% load change Ripple & Noise • <1% of nominal output voltage Overvoltage Protection • >130% Vnom, recycle input to reset Overtemperature • Shuts down at +85 °C, measured internally Protection with auto recovery Overload Protection • 110-140% Short Circuit Protection • Constant current, auto recovery Remote Sense • Compensates for up to 0.5 V drop (not available with current share) Remote On/Off • On = TTL Logic High or Open Off = TTL Logic Low or Short Current Share • Option ‘-I’ available on single output models only - see note 4 Fan Drive • 12 V at 500 mA xppower.com General Efficiency • 3.3 & 5.0 V single output: 70% min, All other single output: 80% min, Dual outputs: 75% min at 230 VAC, full load Isolation • 4000 VAC Input to Output, 1500 VAC Input to Ground, 250 VDC Output to Ground Switching Frequency • 25 kHz for PWM stage, 60 kHz for PFC stage Power Density • 6.25 W/In 3 based on unit without cover/fan Signals • Current Share, Power Good, Current Monitor & optional AC Fail (see note 5 - available on single output models only) MTBF • 140 kHrs at +25 °C per MIL-HDBK-217F Environmental Operating Temperature • -0 °C to +70 °C, derate linearly from +50 °C to+ 70 °C at 2.5%/°C Cooling • Minimum 23 CFM airflow required for maximum power output. ‘-C’ version has built-in fan, others require 23 CFM air flow to meet fan-cooled ratings Operating Humidity • 5-90% RH, non-condensing Storage Temperature • -20 °C to +85 °C Vibration • 5-50 Hz, acceleration 2 g, 3 minute sweep, 60 mins in 3 axes Shock • 15 g 11 ms 1/2 sine wave, 3 times in 6 axes Bump • 15 g 6 ms 1/2 sine 4000 bumps in 3 axes EMC & Safety Emissions • EN55011/22 Level B conducted & radiated Harmonic Currents • EN61000-3-2 ESD Immunity • EN61000-4-2, level 3 Perf Criteria A Radiated Immunity • EN61000-4-3, 3 V/m Perf Criteria A EFT/Burst • EN61000-4-4, level 2 Perf Criteria A Surge • EN61000-4-5, level 3 Perf Criteria A Conducted Immunity • EN61000-4-6, 3 V, Perf Criteria A Dips & Interruptions • EN61000-4-11 70% UT for 10 ms, 40% UT for 100 ms, <5% UT for 5000 ms Perf Crit A, B, B (Perf Crit A, A, B with 85% load) Safety Approvals • UL60601-1, EN60601-1, EN60950-1:2001, UL60950, CSA C22.2 No. 60950-1-03, CSA C22.2 No. 601.1-M90

Voltage(1) Total Output Power Maximum Output Current Model Number(2,3,4,5)V1 V2 3.3 V 198 W 60.00 A SMM400PS03-C† 5.0 V 300 W 60.00 A SMM400PS05-C† 12.0 V 400 W 33.34 A SMM400PS12-C† 15.0 V 400 W 26.60 A SMM400PS15-C† 18.0 V 400 W 22.20 A SMM400PS18-C 24.0 V 400 W 16.70 A SMM400PS24-C† 27.0 V 400 W 14.80 A SMM400PS27-C 36.0 V 400 W 11.10 A SMM400PS36-C 48.0 V 400 W 8.30 A SMM400PS48-C† 54.0 V 400 W 7.40 A SMM400PS54-C 3.3 V/12.0 V 300 W 40.00 A 25.00 A SMM400PD21-C 3.3 V/24.0 V 300 W 40.00 A 12.50 A SMM400PD22-C 5.0 V/12.0 V 300 W 40.00 A 25.00 A SMM400PD23-C 5.0 V/24.0 V 300 W 40.00 A 12.50 A SMM400PD24-C 12.0 V/24.0 V 400 W 25.00 A 12.50 A SMM400PD25-C Notes 1. Other output voltages available. Contact sales. 2. Standard input is screw terminal. For optional IEC320 input and on/off switch, add suffix ‘-D’ to model number. 3. Standard output is screw terminal. For optional Molex output connector, add suffix ‘-G’ to model number. 4. For current share option, add suffix ‘-I’ to model number (remote sense not available). This option also adds internal block diodes. 5. For AC fail option, add suffix ‘-L’to model number (single output only). UVLO function is disabled. Output is low when input is <80 VAC, high (5 V) if input is >86 VAC. 6. When ordering place option suffixes in alphabetical order, e.g. SMM400PS24-CDI. B C B C C B C B B C C B B B CC LLNN 9.01 (228.6) AC Inlet STANDARD ‘-D’ OPTION 0.80 (20.3) 0.80 (20.3) 1.25 (31.8) 1.25 (31.8) 0.50 (12.7) 1.50 (38.1) 1.50 (38.1) 1.60 (40.6) 1.60 (40.6) TERMINAL BLOCK M3 SCREW 3PINS 8.25mm CENTER 5.00 (127.0) 0.88 (22.2) 7.01 (177.8) 7.01 (177.8) 4.00 (101.6) 3.25 (82.6) VO - TERMINAL BLOCK M3.5 SCREW 6PINS 9.5mm CENTER VO + VO + VO - RS+ RS- REM ON/OFF PG RS+ RS- REM ON/OFF PG ACF* RTN RTN CSH CMN FAN FAN RTN Single Dual RTN TERMINAL BLOCK M3.5 SCREW 6PINS 9.5mm CENTER ‘-G’ OPTION ‘-G’ OPTION Mating Connectors Signal Connector (Single): JST XHP-9 Signal Connector (Dual): JST XHP-5 Fan Connector: JST XHP-2 Crimp Terminals: SXH-002-P0.6 ‘-G’ Optional Output: Molex No. 09-91-1600 Crimps: Molex Series 6838 All dimensions in inches (mm). Weight: 2.20 lbs (1.0 kg). † Available from Farnell. See pages 204-206.

Range(1) Total Output Power Maximum Output Current Model Number(2,3,4,5,6)Output 1 Output 2 Convection Fan-Cooled Convection Fan-Cooled Convection Fan-Cooled 3.3 V 148.5 W 198 W 45.00 A 60.00 A SMM400PS03 5.0 V 225.0 W 300 W 45.00 A 60.00 A SMM400PS05 12.0 V 250.0 W 400 W 20.80 A 33.34 A SMM400PS12 15.0 V 250.0 W 400 W 16.60 A 26.60 A SMM400PS15 18.0 V 250.0 W 400 W 13.90 A 22.20 A SMM400PS18 24.0 V 250.0 W 400 W 10.40 A 16.70 A SMM400PS24 27.0 V 250.0 W 400 W 9.20 A 14.80 A SMM400PS27 36.0 V 250.0 W 400 W 6.90 A 11.10 A SMM400PS36 48.0 V 250.0 W 400 W 5.20 A 8.30 A SMM400PS48 54.0 V 250.0 W 400 W 4.60 A 7.40 A SMM400PS54 Mechanical Details SMM Models and Ratings Notes 1. Other output voltages available. Contact sales. 2. For optional solid cover, add suffix ‘-A’ to the model number (external dimensions remain the same). 3. Standard input is screw terminal. For optional Molex input connector, add suffix ‘-F’ to model number. 4. Standard output is screw terminal. For optional Molex output connector, add suffix ‘-G’ to model number. 5. For current share option, add suffix ‘-I’ to model number (remote sense not available). This option also adds internal block diodes. 6. For AC fail option, add suffix ‘-L ’ to model number (single output only). UVLO function is disabled. Output is low when input is <80 VAC, high (5 V) if input is >86 VAC. 7. When ordering place option suffixes in alphabetical order, e.g. SMM400PS24-GI. VO - B B C:MOUNTING HOLE 8 PLACE B B B B C CC C C C1.25 (31.8) 0.80 (20.3) 7.00 (177.8) 1.60 (40.6) 0.5 (12.7) 8.00 (203.2) 3.25 (82.6) LL NN GG 4.00 (101.6) 5.00 ±0.012 (127.0 ±0.3) TERMINAL BLOCK M3.5 SCREW 6PINS 9.5mm CENTER B B C C1.25 (31.8) 0.80 (20.3) 0.50 (12.7) 7.00 (177.8) 0.50 (12.7) VO + VO + VO - RS+ RS- REM ON/OFF PG RS+ RS- REM ON/OFF PG ACF* RTN RTN CSH CMN FAN FAN RTN Single Du al RTN TERMINAL BLOCK M3.5 SCREW 6PINS 9.5mm CENTER ‘-G’ OPTION ‘-F’ OPTION ‘-G’ OPTION Mating Connectors Signal Connector (Single): JST XHP-9 Signal Connector (Dual): JST XHP-5 Fan Connector: JST XHP-2 Crimp Terminals: SXH-002-P0.6 ‘-F’ optional input: Molex No. 09-91-0700 ‘-G’ optional output: Molex No. 09-91-1600 Crimps: Molex Series 6838 All dimensions in inches (mm). Weight: 2.20 lbs (1.0 kg). Mounting holes B: 6-32 Mounting holes C: M4

CN3 Pin 4, control connector PG +5 V 1 K CN3 Pin 2 Output Output Comm Return CN3 Pin 7 Current Share Output Sense Sense LOADTwisted Pair Supply 2 LOAD Output Return CN3 Pin 7 Current Share POWER NOT GOOD POWER GOOD AC FAIL AC GOOD ON/OFF CN3 Pin 3, control connector PSU Return CN3 Pin 6, control connector (single output) CN3 Pin 5, control connector (dual output) Return CN3 Pin 6, control connector PSU CMN CN3 Pin 8, control connector CN3 Pin 6, control connector (single output) CN3 Pin 5, control connector (dual output) Return C CN3 Pin 5, control connector AC Fail +12 V 5 V 1 K CN3 Pin 6, control connector Return Application Notes SMM Remote Sense Optional AC Fail Note: 1. CL is 47 µF electrolytic capacitor. 2. CD is 0.1 µF ceramic capacitor. Remote On/Off Current Monitor Note: 1. Applying <0.3 V or short between pins 5(6) and 3 turns the output OFF . 2. Applying >4.5 V or open circuit between pins 5(6) and 3 turns output ON. Note: 1. 0.5 V to 3.0 V represents 0% to 100% full load. Parallel Connection with Current Share Option Single Output Only Single Output Only Single Output Only Power Good Sink current = 5 mA Source current = 1 mA Sink current = 250 mA Source current = 7 mANote: Current share option includes internal blocking diodes.