SML150PS12 XPPOWER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
- Small Size - 4” x 6” Footprint
- Single Outputs 12-54 VDC
- High Power Density
- 150 W Convection-cooled
- 300 W Fan-cooled
- Temperature-controlled Fan
- PFD & Fan Fail Signals SML Series Input Input Voltage • 90-132 / 180-264 VAC autoranging Input Frequency • 47-63 Hz Input Current • 6.30/3.15 A at 115/230 VAC Inrush Current • 70 A max at 230 VAC, cold start Power Factor • Complies with EN61000-3-2 Class A Earth Leakage Current • 3.5 mA max at 230 VAC Input Protection • Internal 6.3 A / 250 VAC fuse Output Output Voltage • See tables Output Voltage Trim • ±5% Minimum Load • See tables Initial Set Accuracy • ±1% Start Up Delay • 1 s max Start Up Rise Time • 20 ms min at 120 VAC Hold Up Time • 20 ms min at 120 VAC & 80% load Total Regulation • ±1% Over/Undershoot • 5% max at turn on/off Transient Response • 5% max. deviation, recovery to within 1% in 500 µs for a 50% load change Ripple & Noise • 1% pk-pk, 20 MHz BW, see note 1 Overvoltage Protection • <130% Vnom, recycle input to reset Overtemperature • Unit shuts down with auto recovery, Protection measured internally Overload Protection • 110-140%, trip & restart (Hiccup mode) with auto recovery Fan Output • 12 VDC at 500 mA, temperature-controlled (available on 150 W model only) Aux Output • 12 VDC at 500 mA (12.0-14.5 VDC) xppower.com General Efficiency • 75% minimum, 230 VAC 100% load Isolation • 3000 VAC Input to Output
1500 VAC Input to Ground
250 VDC Output to Ground
Switching Frequency • 30 kHz typical Power Density • Up to 6.25 W/In 3 PFD • Open collector signal is LOW when DC is OK Signals • Green LED to indicate power on MTBF • 100 kHrs per MIL-HDBK-217F at +30 ° C Environmental Operating Temperature • -20 °C to +70 °C, derate from +50 °C at 2.5%/°C Cooling • 150 W convection-cooled,
300 W with internal fan
Operating Humidity • 5-90% RH, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000 m Vibration • 5-50 Hz, 7.35 ms 2 on X,Y & Z axis EMC & Safety Emissions • EN55022, level B conducted FCC Part 15 Subject J Class B Voltage Flicker • EN61000-3-3 amendments 1 & 2 ESD Immunity • EN61000-4-2, level 2 Contact, Level 3 Radiated Immunity • EN61000-4-3, level 3 V/m Perf Criteria A EFT/Burst • EN61000-4-4, level 2 Perf Criteria A Surge • EN61000-4-5, level 3 Perf Criteria A Conducted Immunity • EN61000-4-6, level 3 V Perf Criteria A Safety Approvals • EN60950-1, UL60950-1, CSA22.2 No 60950-1
6.00 (152.4) 1.00 (25.4) 4.00 (101.6) 1.00 (25.4) 1.00 (25.4) 2.00 (50.8) A A AA AA CN1 CN2 4.00 (101.6)1.00 (25.4) 3.00 (76.2) 4.00 (101.6) 0.50 (12.7) L N G 4.00 (101.6) 0.08 (2.0) 2.00 (50.8) 1.00 (25.4) 4.00 (101.6) 1.00 (25.4) 1.00 (25.4) 2.00 (50.8) A A A 0.24 (6.3) 0.20 (5.2) 0M4 Mechanical Details SML Models and Ratings Output Power Output Voltage Output Current Ripple & Noise(1) Model NumberMin Max(2) 150 W 12.0 V 1.25 A 12.50 A 1% SML150PS12 13.5 V 1.11 A 11.10 A 1% SML150PS13 15.0 V 1.00 A 10.00 A 1% SML150PS15 18.0 V 0.85 A 8.33 A 1% SML150PS18 24.0 V 0.63 A 6.70 A 1% SML150PS24 27.0 V 0.55 A 5.55 A 1% SML150PS27 30.0 V 0.50 A 5.00 A 1% SML150PS30 36.0 V 0.42 A 4.17 A 1% SML150PS36 48.0 V 0.32 A 3.13 A 1% SML150PS48 54.0 V 0.28 A 2.78 A 1% SML150PS54 300 W 12.0 V 1.25 A 25.00 A 1% SML300PS12 13.5 V 1.11 A 22.20 A 1% SML300PS13 15.0 V 1.00 A 22.00 A 1% SML300PS15 18.0 V 0.85 A 16.66 A 1% SML300PS18 24.0 V 0.63 A 12.55 A 1% SML300PS24 27.0 V 0.55 A 11.00 A 1% SML300PS27 30.0 V 0.50 A 10.00 A 1% SML300PS30 36.0 V 0.42 A 8.33 A 1% SML300PS36 48.0 V 0.32 A 6.25 A 1% SML300PS48 54.0 V 0.28 A 5.55 A 1% SML300PS54 Notes 1. Measured at 20 MHz bandwidth with 0.1 µF ceramic capacitor in parallel with 22 µF electrolytic capacitor. 2. Peak power of 600 W can be taken for 500 µs. Notes 1. Fan drive connector CN1 mates with Molex 22-01-1022 or equivalent with Series 2759 or 5159 crimps. 2. Signal connector CN2 mates with JST XHP-6 or equivalent with JST SXH-002T-P0.6 crimps. 3. Auxiliary 12 V 500 mA supply is regulated between 12 V to 14.5 V. 4. External LED can be connected between ‘PFD LED Drive +’ and ‘PFD’, max current is 5 mA. 5. External LED can be connected between ‘Fan LED Drive +’ and ‘Fan Fail’, max current is 5 mA. 6. Input/Output connector is Howder, part H3-95-7P . 7. Optional cable harness available. Order part number SML LOOM KIT. 8. Maximum mounting screw penetration 0.15 (4.00) from case outer surfaces. All dimensions are in inches (mm). Weight approx 1.75 lb (800 g). 4.00 (101.6) 0.08 (2.0) 2.00 (50.8) A (8 places) 0.24 (6.3) 0.20 (5.2) 0.10 (2.7) 1.00 (25.4)M4 x 0.7 Pin CN1 Fan CN2 Signals 1 Return +12 V, 0.5 Auxiliary 2 +12 V Return