SMC500PS03-C XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

  • High Peak Load Rating
  • Single Outputs from 3.3 V to 54 V
  • Active PFC
  • Remote On/Off
  • Optional Current Share
  • SEMI F47 Compliant
  • Optional Constant Current Limit SMC/SMD Series Input Input Voltage • 90-264 VAC (120-370 VDC) Input Frequency • 47-63 Hz Input Current • 9 A at 90 VAC, 3.5 A at 230 VAC Inrush Current • 40 A at 230 VAC Power Factor • 0.99 typical Earth Leakage Current • <2.4 mA max at 264 VAC Input Protection • Fitted with a T10 A/250 V fuse Output Output Voltage • See tables Output Voltage Trim • ±5% minimum Initial Set Accuracy • ±1% Minimum Load • No minimum load required Start Up Delay • 1.5 s at 230 VAC, 2.5 s at 110 VAC Start Up Rise Time • 40 ms typical Hold Up Time • 18 ms max at 120 VAC Line Regulation • ±0.5%, low line to high line Load Regulation • ±1%, 1-100% of load (see note 4) Over/Undershoot • 5% max Transient Response • 5% max deviation, 500 µs recovery to within 1% for a 50% load change Ripple & Noise • See table Overvoltage Protection • 110-130% recycle input to reset Overtemperature • >85 ˚C ambient with auto recovery Protection (measured internally) Overload Protection • 110% to 135% with auto recovery Short Circuit Protection • Trip and restart (Hiccup mode) Remote Sense • Compensates for up to 0.5 V line dr op Remote On/Off • On = TTL Logic HIGH, or open circuit Off = TTL Logic LOW or short circuit Current Share • Optional single wire current share within 10% for up to 4 units xppower.com General Efficiency • 80% min at 230 VAC, 70% min for Vo ≤5V Isolation • 3000 VAC Input to Output,

1500 VAC Input to Ground,

250 VDC Output to Ground

Switching Frequency • 100 kHz PFC, 25 kHz PWM Power Density • 6.93 W/In 3 Signals • Green LED for Power On, Power Good TTL HIGH within 100-500 ms and LOW ≤1 ms before loss of regulation Current Monitor • 0.5 V to 3 V output voltage denoting 0-100% output current MTBF • 100 kHrs min per MIL-HDBK-217F Environmental Operating Temperature • 0 °C to +70 °C, derate from 100% load at +50 °C to 50% load at +70 °C Cooling • 30 CFM for SMD U-channel versions Operating Humidity • 5-90%, non-condensing Storage Temperature • -20 °C to +85 °C Operating Altitude • 3000 m Shock • 15 g (non-operation), 11 ms (half sine wave), 3 times for each axis Vibration • 10-55 Hz (non-operation) 2 g, sweep time 3 mins, 60 mins/axis EMC & Safety Emissions • FCC Part 15 & CISPR 22 Class B conducted Harmonic Currents • EN61000-3-2, EN61000-3-3 ESD Immunity • EN61000-4-2, level 3 Perf Criteria A Radiated Immunity • EN61000-4-3, 3 V/m Perf Criteria A EFT/Burst • EN61000-4-4, level 2 Perf Criteria A Surge • EN61000-4-5, level 3 Perf Criteria A Conducted Immunity • EN61000-4-6, 3V Perf Criteria A Safety Approvals • UL60950, CSA C22.2 No. 950, EN60950, CE Mark LVD, SEMI F47 Compliant (high line only) at 100% rated power output

Output Voltage(3,4) Output Current Ripple & Noise(2) Model NumberPreset Range Maximum Peak(1) 500 W 600 W 1. This peak can be taken for 500 µs only, average power should not exceed the maximum power. 2. Ripple & Noise is measured using 0.1 µF ceramic and 22 µF electrolytic capacitor, 20 MHz bandwidth. 3. Alternative output voltages available, consult sales. 4. Load regulation increases to 2% for 0-100% load change. 5. For output currents >50 A, please connect remote sense to meet regulation ratings. Notes Derating Curve 1. SMD units require 30 CFM forced air cooling. Notes 0 10 20 30 40 50 60 70 80 Ambient Temperature (˚C) Load (%) 100 Options

  • For U-channel version replace ‘SMC’ in the part number with ‘SMD’ and remove ‘-C’ e.g. SMD600PS12 (See Derating Curve Note 1.)
  • Constant current limit (95-100%) add suffix ‘-B’ (not available on 3.3 V or 5.0 V models)
  • Current share and internal oring diode add suffix ‘-I’ to model number.
  • Optional IEC320 inlet replace suffix ‘-C’ with ‘-D’. Not available for SMD models.
  • For multiple option codes please place optional codes in alphabetical order. e.g. SMC500PS12-BD. † Available from Farnell. See pages 204-206. ^ Available from Newark. See pages 207-208.

2.00 (50.8) 2.50 (63.5) 1.59 (40.4) BA 4.25 (108.0) Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center 5.00 (127.0) 6.00 (152.4) 2.09 (53.0) 1.59 (40.3) 9.17 (233.0) 0.88 (22.25) 2.50 (63.6) 1.75 (44.45) 1.25 (31.9) A B A A A A B B B B 0.59 (15.0) 1.62 (41.25) 0.32 (8.25) N L 2.50 (63.5) Terminal Block M3 Screw 3 Pins 8.25 mm center 2.50 (63.5) IEC320 or equivalent ‘-D’ Option A B B A 9.17 (233.0) 2.00 (50.8) 2.50 (63.5) 2.50 (63.5) FAN Pin 1 Pin 7 A Mounting Hole 8 Places 0.07 (1.9) 0.02 (0.6) 0.22 (5.6) 0.25 (6.4) UNC6-32 (Zn-plated) B Mounting Hole 8 Places 0.07 (1.9) 0.02 (0.6) 0.22 (5.6) 0.25 (6.4) (Zn (yellow) -plated) CN3 SMC/SMD Series Mechanical Details VO-VO+ 2.00 (50.8) 2.50 (63.5) 1.00 (25.4) BA 4.33 (110.0) Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center Terminal Blocks M3.5 Screw 8 Pins 9.5 mm center 5.00 (127.0) 6.00 (152.4) 1.50 (38.1) 1.00 (25.4) 8.00 (203.20) 0.92 (23.25) 0.92 (23.25) 2.50 (63.5) 1.75 (44.45) 1.29 (32.78) 1.29 (32.78) A B A B A A B B NL B A FAN Pin 1 Pin 7 2.50 (63.5) 0.37 (9.5) 2.50 (63.5) 0.37 (9.5) A B B A 2.00 (50.8) 2.50 (63.5)Recommended Air Flow CN3 All dimensions are in inches (mm) Weight: 3.30 lbs (1.5 kg) approx. SMD U-Channel 1. Logic connector CN3 mates with JST XHP-7 or equivalent and JST SXH-002T -P0.6 crimp terminals. 2. Fan connector mates with JST XHP-2 or equivalent and JST SXH-002T-P0.6 crimp terminals. Output is 12 VDC/160 mA 3. Current share only available on ‘-I’ models, remote sense not available on ‘-I’ models. Current share not available with constant current models. 4. Maximum mounting screw penetration: 0.15 (4.00) from case outer surfaces. Notes CN3 (Signals) Pin Function

1 Current monitor

2(3) Current share

3 Return

4 Power good

5 Remote On/Off

6(3) -Remote sense 7(3) +Remote sense SMC with integral fan CN3 (Signals) Pin Function 2(3) Current share 6(3) -Remote sense 7(3) +Remote sense All dimensions are in inches (mm) Weight: 3.09 lbs (1.4 kg) approx.

Application Notes SMC/SMD Series Remote Sense Remote On/Off Power Good Parallel Connection with Current Share Option CL CD CD Supply S CN3 Pin 7 CN3 Pin 4, control connector DC OK +5 V 1 K CN3 Pin 3, control connector Return CN3 Pin 6 Output O Output Sense Sense LOAD Twisted Pair POWER NOT GOOD POWER GOOD PS CN1 Pin 1, control connector Fan Fail +5 V 1 K CN1 Pin 2, control connector Return FAN FAILED FAN OK CL C Supply 1 C Output Comm Return CN3 Pin 2 Current Share O Supply 2 LOAD Output Return CN3 Pin 2 Current Share POWER NOT GOOD POWER GOOD CN3 Pin 5, control connector ON/OFFPSU CN3 Pin 3, control connector Return OFF ON FAN FAILED FAN OK CL CD CD Supply Supply 1 CN3 Pin 7 CN3 Pin 4, control connector DC OK +5 V 1 K CN3 Pin 3, control connector Return CN3 Pin 6 Output O CN3 Pin 2 Curre Output Sense Sense LOAD Twisted Pair Supply 2 L CN3 Pin 2 Curre POWER NOT GOOD POWER GOOD PSU C CN1 Pin 1, control connector Fan Fail +5 V 1 K CN1 Pin 2, control connector Return FAN FAILED FAN OK CL C Supply 1 C Output Comm Return CN3 Pin 2 Current Share O Supply 2 LOAD Output Return CN3 Pin 2 Current Share P Note: 1. CL is 47 µF electrolytic capacitor. 2. CD is 0.1 µF ceramic capacitor. Note: 1. Applying <0.3 V or short between pins 5 and 3 turns the output OFF . 2. Applying >4.5 V or open circuit between pins 5 and 3 turns output ON.