SDX005IND4 SENSORTECHNICS | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

SDX...IND4 Series Compensated pressure sensors in DIP package 1/4June 2008 / 551 www.sensortechnics.com

FEATURES

  • Low cost DIP
  • Temperature compensated
  • Calibrated zero and span
  • Small size
  • Low noise
  • High impedance for low power applications

APPLICATIONS

  • Medical equipment
  • Computer peripherals
  • Pneumatic controls
  • H V A C EQUIVALENT CIRCUIT Scale: 1 cm ½ inch ELECTRICAL CONNECTION Top view Note: The polarity identicated is for pressure applied to P2 (backward gage). GENERAL DESCRIPTION The SDX...IND4 sensors will provide a very cost effective solution for pressure applications that require small size plus performance. These calibrated and temperature compen- sated sensors give an accurate and stable output over a 0 to 50°C tem- perature range. This series is inten- ded for use with non-corrosive, non- ionic working fluids such as air, dry gases and the like. The SDX...IND4 devices are speci- fically designed to measure low pressures. They feature a 0 to 5 or 0 to 10 "H 2O full scale range. The output of the bridge is ratiometric to the supply voltage and operation from any D.C. supply voltage up to +20 V is acceptable. The SDX...IND4 devices feature an integrated circuit sensor element and laser trimmed thick film ceramic housed in a compact solvent resistant case. The package is a double wide (i.e., 0.600" lead spacing) dual-inline- package. This is the same familiar package used by IC manufacturers except that is has a pressure port(s). The PC board area used by each DIP is approximately 0.26 square inches. This extremely small size enables the use of multiple sensors in limited available space. The DIP provides excellent corrosion resistance and isolation to external package stress. The DIP mounts on a PC board like a standard IC with through-hole pins. The pins anchor the pressure sensor to the PC board and provide a more secure and stable unit than other types of packages. +out V -out P1GND out - 1out + +Vs

SDX...IND4 Series Compensated pressure sensors in DIP package 2/4June 2008 / 551 www.sensortechnics.com PERFORMANCE CHARACTERISTICS 1 Specification notes: 10. Reference conditions (unless otherwise noted): supply voltage, V S = 12VDC ; TA = 25°C; common mode line pressure = 0 psig; pressure applied to port 2. Span is the algebraic difference between the output voltage at full scale pressure and the output at zero pressure. Span is ratiometric to the supply voltage. Hysteresis is the maximum output difference at any point within the operating pressure range for increasing and decreasing pressure. Maximum error band of the offset voltage and the error band of the span, relative to the 25°C regarding. Difference in output at any pressure with the operating pressure range and temperature within 0°C to +50°C after: a) 100 temperature cycles, 0°C to +50°C. b) 1.0 million pressure cycles, 0 psi to full scale span. Input impedance is the impedance between V S and ground. Output impedance is the impedance between the + and - outputs. This is the common mode voltage of the output arms for V S = 12 VDC . Response time for a 0 psi to full scale span pressure step change, 10 % to 90 % rise time. Long term stability over a one year period. PRESSURE SENSOR CHARACTERISTICS (all devices) Maximum ratings Supply voltage VS +20 VDC Lead temperature (soldering 4 sec.)250°C Environmental specifications Temperature ranges Compensated 0°C to 50°C Operating -40°C to +85°C Storage -55°C to +125°C Humidity limits (non condensing) 0 to 99% RH scitsiretcarahC. niM. pyT. xaMt inU tesffoerusserporeZ0 .1-00 .1± Vm napselacslluF 2 4DNI500XDS5 .910 .025 .02 4DNI010XDS5 .420 .525 .52 )C°05otC°0(stceffe.pmeT 4 tesffO- --2 .0±6 .0± napS- --4 .0±0 .2± OSF%siseretsyhdnaytiraenildenibmoC 3 ---2 .0±0 .1± ytilibataepeR 5 ---5 .0±- -- napsdnatesffofoytilibatsmretgnoL 01 ---1 .0±- --V m emitesnopseR 9 ---0 01- --s µ ecnadepmitupnI 6 ---0 .4- -- kΩecnadepmituptuO 7 ---0 .4- -- egatlovedomnommoC 8 5.10 .30 .5V CD STANDARD PRESSURE RANGES Part number SDX005IND4 SDX010IND4 Operating pressure 0...5 "H2O 0...10 "H2O Proof pressure 200 "H2O 200 "H2O Burst pressure 10 psi 10 psi Common mode pressure 50 psig 50 psig

SDX...IND4 Series Compensated pressure sensors in DIP package 3/4June 2008 / 551 www.sensortechnics.com PHYSICAL DIMENSIONS D4-housing mass: 2 g dimensions in inches (mm) GENERAL DISCUSSION The SDX...IND4 series devices give a voltage output which is directly proportional to applied pressure. The gage devices will give an increasing positive going output when increasing pressure is applied to the pressure port. The devices are ratiometric to the supply voltage and changes in the supply voltage will cause proportional changes in the offset voltage and full scale span. 0.300 (7.62) 0.600 (15.24) typ. 0.470 (11.94) 0.550 (13.97) 0.430 (10.92) typ. Ø 0.090 (2.29) typ. 0.100 (2.54) typ. 0.020 (0.51) typ. compensation circuit 0.010 (0.25) typ. 0.120 (3.05) typ. 0.335 (8.50) typ. 0.110 (2.79) typ. 0.135 (3.43) 0.250 (6.35)

SDX...IND4 Series Compensated pressure sensors in DIP package 4/4June 2008 / 551 www.sensortechnics.com Sensortechnics and Sensym reserve the right to make changes to any products herein. Sensortechnics and Sensym do not assume any liability arising out of the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others. PNEUMATIC INTERFACE The DIP also provides convenient mounting and pressure ports for ease of use with standard 1/16" ID, 1/8" OD, 1/32" wall, flexible plastic tubing for pressure connection. The small tubing has several advantages over larger tubing commonly used with pressure sensors: 1) The tubing can be formed in a much smaller radius with-out kinking. 2) The tubing is easier to handle. 3) The tubing is available in a variety of colors such as clear, white, yellow, blue, green, etc. to enable color coding of pneumatic circuits with multiple pressure sensors in the same way that wiring harnesses are color coded in electrical circuits. This greatly simplifies troubleshooting. 4) Less stress is placed on the pressure sensor package resulting in less potential for offset shifts. 5) Less physical space is required for the small tubing. 6) The lower volume of air in the small tubing results in faster pressure sensor response. USER CALIBRATION The SDX...IND4 devices are fully calibrated for offset and span and should therefore require little user adjustment in most applications. For more precise span and offset adjustments, contact the factory. MEDIA COMPATIBILITY SDX...IND4 devices are compatible with most non-corrosive gases. For questions concerning media compatibility, contact the factory.

APPLICATION INFORMATION

Application information found in the section "Application Notes" and on the SCX series data sheet in the "Sensortechnics pressure sensors, transducers and transmitters handbook".

ORDERING INFORMATION

H"5-0 2O4 DNI500XDS H"01-0 2O4 DNI010XDS