SDM XPPOWER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

300 Watts

  • Me dicalApprovals
  • 3.2” x 5” Footprint
  • Fits1U Ap plications
  • High Efficiency
  • Up to 600 W Peak Power
  • Single& DualOutputs
  • 3 YearWa rranty SDM Series Input InputVoltage • 90-264 VAC InputFrequency • 47-63 Hz InputCurrent • 5.0 A at 90 VAC, 2 A at 230 VAC InrushCurrent • Max 70 A at 230 VAC, 35 A at 115 VAC, cold start 25 °C Power Factor • >0.9 EarthLeakage Current • <250 µA at 264 VAC, 60 Hz InputProtection • T5 A / 350 V internal in line fuse Output Output Voltage • See table Output VoltageTrim • ±5% on V1 (V2 of dual output models will track by same % of adjustment) InitialSet Accuracy • ±1% Minimum Load • 10% on both outputs of dual output models StartUp Delay • 1.1 s max at 120 VAC StartUp Rise Time • 100 ms typical Hold Up Time • 16 ms min at 80% of full load, 120 VAC LineRegulation • ±0.5% Load Regulation • ±1% 1-100% load for single outputs ±3% V1, ±7% V2 for dual output models Over/Undershoot • 5% max TransientResponse • 5% max deviation, recovery to within 1% in 2.5 ms for a 50% load change Ripple& Noise • 1% pk-pk (see note 1) OvervoltageProtection • 110-130% Vnom on output V1, recycle input to reset Overtemperature • Measured internally with auto recovery Protection OverloadProtection • 110-140% ShortCircuitProtection • Trip & restart (hiccup mode), auto recovery Remote On/Off • Requires a low signal to inhibit output Fan Supply • 12 VDC, 300 mA, not available on ‘-F’, ‘-E’ or ‘-K’ versions with built-in fan xppo w er.com Ge neral Efficiency • Single output models: typically 86% Dual output models: typically 82% Isolation • 4000 VAC Input to Output

1500 VAC Input to Ground

250 VDC Output to Ground

SwitchingFrequency • 40-70 kHz PFC variable, 55 kHz - 75 kHz PWM fixed Power Density • 12.5 W/in 3 Signals • Power Good goes Hi 100-500 ms after output is in regulation and goes Low at least 0.6 ms before loss of regulation MTBF • 116 kHrs to MIL-HDBK-217F at 25 °C, GB Environm ental OperatingTemperature • -10 °C to +70 °C, derate at 2.5%/ °C from +50 °C to +70 °C StorageTemperature • -20 °C to +85 °C OperatingHumidity • 5-90%, non-condensing StorageHumidity • 5-95%, non-condensing Cooling • ‘-F’, ‘-E’ & ‘-K’ versions have built-in fan, others require 15 CFM to meet forced air ratings OperatingAltitude • 3000 m Shock • 30 g, 11ms half sine, 6 axes Vibration • 2 g, 10-200 Hz, 3 axes EMC & Safety Emissions • EN55011 Level B conducted & radiated Harmonic Currents • EN61000-3-2 class A EN61000-3-2 class C for loads ≥40% VoltageFlicker • EN61000-3-3 ESD Immunity • EN61000-4-2, level 3 Perf Criteria A RadiatedImmunity • EN61000-4-3, 3 V/m Perf Criteria A EFT/Burst • EN61000-4-4, level 2 Perf Criteria A Surge • EN61000-4-5, installation class 3, Perf Criteria A Conducted Immunity • EN61000-4-6, 3V Perf Criteria A Dips & Interruptions • EN61000-4-11, 30% 500 ms, 60% 100 ms, 100% 10 ms, 100% 5000 ms, Perf Criteria A, A, A, B at 230 VAC and

100 VAC with reduced load

SafetyApprovals • ANSI/AMMI ES60601-1, CSA C22.2 No. 60601-1, EN60601-1, All 3rd Edition

SDM 30 0 M odelsand Ratings Output Voltage Output Power Output Current Model Number (3,4,5,6) Nominal Peak (2) 12 V 300 W 25.00 A 50.00 A SDM300PS12-F 15 V 300 W 20.00 A 40.00 A SDM300PS15-F (6) 24 V 300 W 12.50 A 25.00 A SDM300PS24-F 36 V 300 W 8.33 A 16.67 A SDM300PS36-F (6) 48 V 300 W 6.25 A 12.50 A SDM300PS48-F V1: +5.00 V V2: +12.0 V 240 W 24.00 A 13.3 A 28.80 A

16.00 A SDM300PD0512-F

V1: +12.0 V V2: +24.0 V 240 W 13.33 A 6.67 A 16.00 A

8.00 A SDM300PD1224-F

  1. R ipple & noiseis measured using a 0.1 µF ceram iccapacitorinparallelwith 22µF electrolyticand 20 MH z bandwidth 2.Peak load can be takenfor 500 µs.A verage power notto exceed m ax power. 3.R eplace suffix‘-F’withsuffix ‘-E’forend fancoverw ithscrew terminaloption e.g.SD M300PS 24-E or suffix‘K-E’ forend fan coverwith IEC inletoptione.g. SD M3 00PS24K-E 4.Add suffix ‘D’foroptionaloutputterminalblockon single outputmodels exceptthe12 V output models w hichareonlyavailablewith output terminalblocks eg. SDM 300PS24D-F. (6) 5.Add suffix ‘G’foroptionalinputterminalblockseg.SDM3 00PS24DG-F, except forenclosed withend fan(option ‘-E’)which has input terminalblocks as standard. (6 ) 6 .A vailable forOE M quantities,contactSales. 1. All dimensions are in inches (mm 2. Tolerance: ±0.012 (±0.3) 3. Weight: Enclosed with top fan (option ‘-F’): 1.32 lbs (600 g) Enclosed with end fan (option ‘-E’ &’-K’): 1.43 lbs (650 g) 4. Mounting holes and mating half connectors common to all models. Enclosed withtop fan Me chanicalDetails CN1 1.60 (40.64) 3.20 (81.28) 0.20 (0.5) 2.23 (56.75) 5.00 (127.00) 0.75 (19.05) A A 4.50 (114.30) 0.25 (6.35) 0.25 (6.35) Voltage Adj. internally on daughter board DCOK RTN FF INH CN3 CN2 CN2 SINGLE DUAL See Connector Notes for mating parts Input Connector FG N L VO- VO+ RTN Voltage Adj. internally on daughter board DCOK RTN FF INH CN3 CN2 CN2 SINGLE DUAL See Connector Notes for mating parts Input Connector Terminal block 3 pins 0.25 (6.35) center HD-602-3P A A A A AA 6.50 (165.10) 0.33 (8.26) 0.33 (64.77) 4.50 (114.30) 3.20 (81.28) 1.60 (40.64) 0.25 (6.35) VO- VO+ RTN A Mounting hole 6 places M3 x 0.5 ax. screw penetration 0.15 (3.8) Enclosed withend fan(Option‘-E ’)

SDM3 00 Mode lsand Ratings Output Voltage Output Power Output Current Model Number (3,4,5) Forced Cooled ConvectionCooled Forced Cooled ConvectionCooled Peak (2) 12 V 300 W 150 W 25.00 A 12.50 A 50.00 A SDM300PS12 15 V 300 W 150 W 20.00 A 10.00 A 40.00 A SDM300PS15 (6) 24 V 300 W 150 W 12.50 A 6.25 A 25.00 A SDM300PS24 36 V 300 W 150 W 8.33 A 4.17 A 16.67 A SDM300PS36 (6) 48 V 300 W 150 W 6.25 A 3.12 A 12.50 A SDM300PS48 V1: +5.00 V V2: +12.0 V 240 W 120 W 24.00 A 13.3 A 12.00 A 6.67 A 28.80 A

16.00 A SDM300PD0512

V1: +12.0 V V2: +24.0 V 240 W 120 W 13.33 A 6.67 A 6.67 A 3.33 A 16.00 A

8.00 A SDM300PD1224

1.R ipple & noise isme asured using a 0.1 µF ceramic capacitorinparallelwith 22µF electrolytic and 20 M Hz bandw idth 2.Peak load can be taken for500 µs.A verage power not to exceed m ax power. 3. A dd suffix‘D’foroptionaloutputterminalblockon singleoutputm odels except the 12 V outputm odels w hich areonlyavailablewith 4.Add suffix ‘G’foroptionalinputterminalblocks eg.SDM3 00PS 24DG-F, except for enclosed withend fan(option ‘-E’)which has inputterminalblocks as standard. (6 ) 5.Add suffix ‘H’foroptionalmolex outputterminalon dualoutputmodels used in convection applications. (6 ) 6 .Available forO EM quantities,contactSales. U-Channel Mec hanicalD etails 3.20 (81.28) 0.75 (19.05) A AA A A A 0.55 (13.90) 2.70 (68.58) 0.32 (8.26) 2.55 (64.77) L N G 1.75 (44.52) 5.00 (127.00) 1.50 (38.10) 4.50 (114.30) 0.25 (6.35) 0.25 (6.35) CN1 Voltage Adj. internally on daughter board DUAL DCOK RTN FF INH CN3 FAN FAN DCOK RTN FF INH CN3 CN2 SINGLE See Connector Notes for mating parts Input Connector FG N L FF FF VO- VO+ CN2 RTN Notes 1. All dimensions are in inches (mm 2. Tolerance: ±0.012 (±0.3) 3. Weight: U-Channel: 1.1 lbs (500 g) 4. Mounting holes and mating half connectors common to all models. AC -D C

Remote On/Off (INH) Fan Fail(FF) Power Good (PG) Thermal Considerations- U Channel Terminal block 3 pins 0.25 (6.35) center HD-601-3P INPUT CONNECTORS Standard Option ‘G’ L N G NEUTRAL FG LINE CN1 Mating JST part no. VHR-5N or equivalent (5 pin, 3 used) Crimp contacts for JST VHR Series: SVH-21T-P1.1 - 22~18awg SVH-41T-P1.1 - 20~16awg CN2 CN2 OUTPUT CONNECTORS Standard VO- VO+ Single Output models Mating JST part no. VHR-6N or equivalent RTN V1 Dual Output models Terminal block M3 screws 0.33 (8.25) 3 pins Max torque 7 lbs-in (0.8 Nm) HD-816-3P SIGNALS & FAN CONNECTORS CN3 P .G FF RTN INH FAN1 FF Mating JST Part No XHP-3 with SXH-002T-P0.6 Pins Mating JST Part No XHP-4 Housing SXH-002T-P0.6 Pins CN3 Pin 3 Fan Fail CN3 Pin 2 Return CN3 Pin 4 On/Off PSU CN3 Pin 2 Return CN3 Pin 1 DC OK +5 V 1 K CN3 Pin 2 Return PSU 0.59 (15.0) Input Output 0.59 (15.0) Input Output C6 T1 C26 C21 C26 C21 POWER NOT GOOD POWER GOOD No te: 1. Applying <0.3 V or short between pins 4 and 2 turns the output OFF. 2. Applying >4.5 V or open circuit between pins 4 and 2 turns output ON. N ote: 1. Open collector signal: 28 V maximum voltage and 5 mA (maximum sink current) TransistorOn :Fan OK TransistorOff:Fan Fail No te: Sink current = 6 mA, Source current = 1 mA Power is good 100-500 ms after output is in regulation. Power not good at least 1 ms before loss of regulation. In order to ensure safe operation of the PSU in the end-use equipment, the temperature of the components listed in the table (right) must not be exceeded. See drawing above for component locations. The temperature should be monitored using K type thermocouples placed on the hottest part of the component (out of any direct airflow). Temperature Measurement Component Max Continuous Temp ºC C26 85 C6 105 C21 105 L6 130 T1 Coil 140 RTN Dual Output models Mating JST part no. VHR-8N or equivalent OPTIONAL OUTPUT CONNECTORS (1) CN2 CN2 Option ‘D’(Standard on 5-12 V models) Option ‘H’(only on dual output models in convection-cooled applications) Dinkle PCB terminals P-830 N 2 pins M5 screws Max torque 15.7 lbs-in (1.8 Nm) AC-DC 1. AvailableforO EM quantities,contactSales. SingleOutputModels Dual OutputModels (1)