SD321

SD321 SHOUDING | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 9

Technical content

Features

=5 V ,T A = 25˚C. Typical values unless specified). n Gain-Bandwidth product 1MHz n Low supply current 430µA n Low input bias current 45nA n Wide supply voltage range +3V to +32V n Stable with high capacitive loads

Applications

n Industrial: controls, instruments n Desktops n Communications infrastructure Connection Diagram SOT23-5 Top View Application Circuit DC Summing Amplifier IN’s ≥ 0V DC and V O ≥ V DC Where: V ,( V )≥ (V ) to keep V O DC

Ordering Information

1www.shouding.net 12.Sep.01

(Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Differential Input Voltage Supply Voltage Input Current (V IN −0.3V) (Note 6) 50mA Supply Voltage (V ) 32V Input Voltage −0.3V to +32V Output Short Circuit to GND, V ≤ 15V and T A = 25˚C (Note 2) Continuous Storage Temperature Range −65˚C to 150˚C Junction Temperature (Note 3) 150˚C Mounting Temperature Lead Temp (Soldering, 10 sec) 260˚C Infrared (10 sec) 215˚C Thermal Resistance to Ambient (θ JA ) 265˚C/W ESD Tolerance (Note 10) 300V Operating Ratings (Note 1) Temperature Range −40˚C to 85˚C Supply Voltage 3V to 30V

Electrical Characteristics

Unless otherwise specified, all limits guaranteed for at T A = 25˚C; V = 5V, V 0V, V O = 1.4V.Boldfacelimits apply at temperature extremes. Symbol Parameter Conditions Min (Note 5) Typ (Note 4) Max (Note 5) Units V OS Input Offset Voltage (Note 7) 2 7 mV I OS Input Offset Current 5 50 150 nA I B Input Bias Current (Note 8) 45 250 500 nA V CM Input Common-Mode Voltage Range V = 30V (Note 9) For CMRR = 50dB - 1.5 V V A V Large Signal Voltage Gain (V = 15V, R L =2 kΩ V O = 1.4V to 11.4V)

100 V/mV

PSRR Power Supply Rejection Ratio R S ≤ 10kΩ , V ≤ 5V to 30V 65 100 dB CMRR Common Mode Rejection Ratio R S ≤ 10kΩ 65 85 dB V O Output Swing V OH V = 30V, R L =2 kΩ 26 VV = 30V, R L = 10kΩ 27 28 V OL V = 5V, R L = 10kΩ 52 0 mV I S Supply Current, No Load V = 5V 0.430 0.7 1.15 1.2 mA V = 30V 0.660 1.5 2.85 I SOURCE Output Current Sourcing V ID = +1V, V = 15V, V O =2 V mA I SINK Output Current Sinking V ID = −1V V = 15V, V O =2 V 8 mA V ID = −1V V = 15V, V O = 0.2V 12 100 µA I O Output Short Circuit to Ground (Note 2) V = 15V 40 85 mA SR Slew Rate V = 15V, R L =2 kΩ , V IN = 0.5 to 3V C L = 100pF, Unity Gain

0.4 V/µs

GBW Gain Bandwidth Product V = 30V, f = 100kHz, V IN = 10mV, R L =2 kΩ , C L = 100pF

1 MHz

φm Phase Margin 60 deg SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

Unless otherwise specified, all limits guaranteed for at T A = 25˚C; V = 5V, V 0V, V O = 1.4V.Boldfacelimits apply at temperature extremes. (Continued) Symbol Parameter Conditions Min (Note 5) Typ (Note 4) Max (Note 5) Units THD Total Harmonic Distortion f = 1kHz, A V = 20dB R L =2 kΩ ,V O =2 V PP C L = 100pF, V = 30V 0.015 % e n Equivalent Input Noise Voltage f = 1kHz, R S = 100Ω V = 30V 40 nV/ Note 1:Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics. Note 2:Short circuits from the output V can cause excessive heating and eventual destruction. When considering short circuits to ground the maximum output current is approximately 40mA independent of the magnitude of V . At values of supply voltage in excess of +15V, continuous short circuits can exceed the power dissipation ratings and cause eventual destruction. Note 3:The maximum power dissipation is a function of T J(MAX) , θ JA , and T A . The maximum allowable power dissipation at any ambient temperature is P D =( T J(MAX) A )/θ JA . All numbers apply for packages soldered directly onto a PC board. Note 4:Typical values represent the most likely parametric norm. Note 5:All limits are guaranteed by testing or statistical analysis. Note 6:This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action on the IC chip. This transistor action can cause the output voltages of the op amps to go to the V voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.36V (at 25˚C). Note 7:V O ≅ 1.4V, R S =0 Ω with V from 5V to 30V; and over the full input common-mode range (0V to V - 1.5V) at 25˚C. Note 8:The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the outputs o no loading change exists on the input lines. Note 9:The input common-mode voltage of either input signal voltage should not be allowed to go negative by more than 0.3V (at 25˚C). The upper end of the common-mode voltage range is V - 1.5V at 25˚C, but either or both inputs can go to +32V without damage, independent of the magnitude of V Note 10:Human Body Model, 1.5kΩ in series with 100pF. Simplified Schematic 20007603 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

Typical Performance Characteristics Unless otherwise specified, V S = +5V, single supply, T A = 25˚C. Small Signal Pulse Response Large Signal Pulse Response 20007604 20007605 Supply Current vs. Supply Voltage Sinking Current vs. Output Voltage 20007612 20007613 Source Current vs. Output Voltage Open Loop Frequency Response 20007617 20007614 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

The bias network of the SD321 establishes a supply current The SD321 op amp can operate with a single or dual power Application Hints supply voltage, has true-differential inputs, and remain in the linear mode with an input common-mode voltage of 0 V DC This amplifier operates over a wide range of power supply voltages, with little change in performance characteristics. At 25˚C amplifier operation is possible down to a minimum supply voltage of 3V. Large differential input voltages can be easily accommo- dated and, as input differential voltage protection diodes are not needed, no large input currents result from large differ- ential input voltages. The differential input voltage may be larger than V without damaging the device. Protection should be provided to prevent the input voltages from going negative more than −0.3 V DC (at 25˚C). An input clamp diode with a resistor to the IC input terminal can be used. To reduce the power supply drain, the amplifier has a class A output stage for small signal levels which converts to class B in a large signal mode. This allows the amplifiers to both source and sink large output currents. Therefore both NPN and PNP external current boost transistors can be used to extend the power capability of the basic amplifiers. The output voltage needs to raise approximately 1 diode drop above ground to bias the on-chip vertical PNP transistor for output current sinking applications. For AC applications, where the load is capacitively coupled to the output of the amplifier, a resistor should be used, from the output of the amplifier to ground to increase the class A bias current and to reduce distortion. Capacitive loads which are applied directly to the output of the amplifier reduce the loop stability margin. Values of 50pF can be accommodated using the worst-case non-inverting unity gain connection. Large closed loop gains or resistive isolation should be used if large load capacitance must be driven by the amplifier. which is independent of the magnitude of the power supply voltage over the range of from 3 V DC to 30 V DC Output short circuits either to ground or to the positive power supply should be of short time duration. Units can be de- stroyed, not as a result of the short circuit current causing metal fusing, but rather due to the large increase in IC chip dissipation which will cause eventual failure due to exces- sive junction temperatures. The larger value of output source current which is available at 25˚C provides a larger output current capability at elevated temperatures than a standard IC op amp. The circuits presented in the section on typical applications emphasize operation on only a single power supply voltage. If complementary power supplies are available, all of the standard op amp circuits can be used. In general, introduc- ing a pseudo-ground (a bias voltage reference of V /2) will allow operation above and below this value in single power supply systems. Many application circuits are shown which take advantage of the wide input common-mode voltage range which includes ground. In most cases, input biasing is not required and input voltages which range to ground can easily be accommodated. Typical Applications Non-Inverting DC Gain (0V Input = 0V Output) 20007606 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

(Continued) Amplitude Modulator Circuit DC Summing Amplifier IN’s ≥ 0V DC and V O ≥ V DC 20007602 20007607 Where: V ,( V )≥ (V ) to keep V O DC Power Amplifier LED Driver 20007608 V =0V DC for V IN =0V DC V =1 0 20007609 Fixed Current Sources Lamp Driver 20007610 20007611 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

SOT23-5 Tape and Reel Specification TAPE DIMENSIONS 20007615 8mm 0.130 (3.3) 0.124 (3.15) 0.130 (3.3) 0.126 (3.2) 0.138 0.002 (3.5 0.05) 0.055 0.004 (1.4 0.11) 0.157 (4) 0.315 0.012 0.3) Tape Size DIM A DIM Ao DIM B DIM Bo DIM F DIM Ko DIM P1 DIM W SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

SOT23-5 Tape and Reel Specification (Continued) REEL DIMENSIONS 20007616 8mm 7.00 330.00 0.059 1.50 0.512 13.00 0.795 20.20 2.165 55.00 8.40 + 1.50/−0.00 0.567 14.40 W1 + 0.078/−0.039 W1 + 2.00/−1.00 Tape Size A B C D N W1 W2 W3 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01

inches (millimeters) unless otherwise noted 5-Pin SOT23 SD321Low Power Single Op Amp www.shouding.net 12.Sep.01