SC50462 SILAN | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 11

Technical content

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 1 of 12 INFRARED REMOTE CONTROL TRANSMITTER OF 50462 CODE FORMAT

DESCRIPTION

The SC50462 is a remote control transmitter utilizing CMOS technology specially designed for use on infrared applications. It has 64 functions and a total of 76 commands can be transmitted. Housed in 24 pins DIP package, SC50462 has 2 address bits.

FEATURES

  • High performance CMOS technology * Low power consumption * Least external components. * Up to 76 instructions * Double key operation is possible.

APPLICATIONS

  • Television remote control transmitter * Video cassette recorder(VCR) remote control transmitter

ORDERING INFORMATION

SC50462 SDIP­24­300­2.54 SC50462S SOP­24­375­1.27 BLOCK DIAGRAM Key encoder

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 2 of 12 ABSOLUTE MAXIMUM RATINGS(Ta mb=25°C) Characteristic Symbol Ratings Unit Supply Voltage VCC ­0.3 ~ 5.5 V Input Voltage VIN Vss­0.3V ~ VCC+0.3V V Output Voltage VOUT V ss ~ VCC V Power Dissipation PD 300 mW Operating Temperature Topr ­10 ~ +70 °C Storage Temperature Tstg ­40 ~ +125 °C ELECTRICAL CHARACTERISTICS(Ta mb=25°C,VCC=3.0V,Vss=0,Unless otherwise specified) Parameter Symbol Test Conditions Min Typ Max Unit Operating Supply Voltage VCC Ta mb=20 ~ 70°C 1.8 3 5 V Operating Supply Current ICC1 fosc=455kHz 0.3 mA Stand­by Current ICC2 1 µ A High level Output Current(OUT ) IOH VOH=2V 5 mA Low level Output Current(OUT ) IOL VOL=1V ­3 mA High level Output Current(CNTR ) IOH VOH=2V 1 mA Low level Output Current(CNTR ) IOL VOL=1V ­3 mA PIN CONFIGURATION 12 13 Vss OSCI OSCO CNTR I8 S1 OUT Vcc SC50462

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 3 of 12 PIN DESCRIPTION Pin No. Pin Name Description 1,24 VSS, VCC Power Supply: VCC=3.0V,VSS=0V 2,3 OSCI,OSCO Oscillator Input/Output Pin, 455 or 480kHz Crystal is connected between these pins. 4 CNTR Transmitting Indicator. An LED and resistor are connected from this pin to Vcc. 5~12 I1~I8 Key Scan Signal Input pins. 13~20 S1~S8 Key Scan Signal Output pins. 21,22 C4 C5, Custom Code

23 OUT Modulation Pin

SC50462 is a sending signal IC on infrared remote control. Consisting of timing generating circuit, scan signal generating circuit, key input encoder, instruction decoder, custom code circuit, code encoder, and output buffer. It has 8*8 key matrix input and custom code with 16 bit PCM which shows 76 instructions.76Instruction are devided in 64 one shot signal and 12 2­shot signal. When Input Signal(I1~I8) and/or in combination with the Scan Signals(S1~S8) are activated, SC50462 checks the ID and the Custom Code Bits­­ 4C and 5C ­­setting before finally sending out the remote control signal. 1. CNTR OUTPUT The CNTR Pin is the LED transmission Indicator. This means that Whenever a valid transmission is sent, the LED lights up. The CNTR output becomes “ L” in the 7th pulse­rising and “ H” in the 17th pulse­rising. Note: Oscillator Frequency=480 or 455kHz 2. OSCILLATING CIRCUIT An oscillator circuit may be constructed by using a 480kHz or 455kHz Crystal Resonator and two capacitors. Please refer to the following diagram. The carrier frequency transmitted is 40kHz or 37.9kHz.Unless any legal key input is activated, the oscillation is automatically stopped. Thus ,power consumption is considerably reduced.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 4 of 12 3. KEY INPUT A total of 64 keys may be connected by Input Pins(I1~I8) and Output Pins(S1~S8) to form an 8x8 Key Matrix. Double key operation is possible for only one of the keys— SW25~SW28 in combination with any one of the keys – SW11~SW13. Any other key combination are regards as illegal and will not generate any activity. Thus, only the following key combinations may be used for the doubled key operation: I8 I7 I6 I5 I4 I3 I2 I1 SW11 SW12 SW13 SW25 SW26 SW27 SW28 SW25 and SW 11 SW25 and SW 12 SW25 and SW 13 SW26 and SW11 SW26 and SW12 SW26 and SW13 SW27 and SW 11 SW27 and SW 12 SW27 and SW 13 SW28 and SW11 SW28 and SW12 SW28 and SW13 Note: SC50462 permits two keys function but only “ ” key are allowed. When you push one key of SW11/12/13, you can push with another key of SW25/26/27/28. Otherwise, other conditions are illegal. 4. TRANSMISSION CODE The transmission Code consists of 16 bits, namely: 8 bits custom code(C0~C7 ) and 8 bits data code (D0~D7). Please refer to the table below: C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 Custom Code Data Code One frame of the Transmission Code If a Single Shot Key is depressed, data Codes— D6 and d7 will be given the value of (0,0).Please refer to the table1.If a valid double key operation is perform ed, the data codes will receive the values described in Table 2. Table 1: Key Matrix/Code Data Scan Output D0 D1 D2 Octal display S1 0 0 0 0 S2 1 0 0 1 S3 0 1 0 2 S4 1 1 0 3 S5 0 0 1 4 S6 1 0 1 5 S7 0 1 1 6 S8 1 1 1 7

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 5 of 12 Data Key Input D3 D4 D5 Octal display I1 0 0 0 0 I2 1 0 0 1 I3 0 1 0 2 I4 1 1 0 3 I5 0 0 1 4 I6 1 0 1 5 I7 0 1 1 6 I8 1 1 1 7 Table 2: Double Key Signal/Code Data Code Octal Display Scan Output D0 D1 D2 D3 D4 D5 D6 D7 D0~D2 D3~D5 D6~D7 S5/I2 (SW25) 0 0 1 1 0 0 1 0 4 1 1 S6/I2 (SW26) 1 0 1 1 0 0 1 0 5 1 1 S7/I2 (SW27) 0 1 1 1 0 0 1 0 6 1 1 S1/I1 (SW1 S8/I2 (SW28) 1 1 1 1 0 0 1 0 7 1 1 S5/I2 (SW25) 0 0 1 1 0 0 0 1 4 1 2 S6/I2 (SW26) 1 0 1 1 0 0 0 1 5 1 2 S7/I2 (SW27) 0 1 1 1 0 0 0 1 6 1 2 S2/I1 (SW1 S8/I2 (SW28) 1 1 1 1 0 0 0 1 7 1 2 S5/I2 (SW25) 0 0 1 1 0 0 1 1 4 1 3 S6/I2 (SW26) 1 0 1 1 0 0 1 1 5 1 3 S7/I2 (SW27) 0 1 1 1 0 0 1 1 6 1 3 S3/I1 (SW1 S8/I2 (SW28) 1 1 1 1 0 0 1 1 7 1 3 5. CUSTOM CODE SC50462 has a total of 8 bits custom code (C0~C7). Custom Code Bits – C4 and C5 can be externally selected using the 4C and 5C Terminals. The 4C and 5C pins are inversed; therefore, if the 4C and 5C terminals are pulled HIGH, then the Custom Code Bits— C4 and C5 would have the Value(0,0). Likewise, when pulled LOW, then C4 and C5 bits will be (1,1),The other Customs Code Bits,namely:C0~C3 and C6,C7 are fixed at (1,1,1,0) and (1,0 ): The waveform of bits are given below: 0.25/0.26ms 1.00/1.05ms 2.00/2.10ms Bit "0" Bit "1" Note: Oscillator Frequency=480 or 455kHz

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 6 of 12 6. KEY ON TIMING When any key is pressed, the output pin­­ OUT continuously generates the waveform described below until the key is released. KEY ON OUT 1st Frame 2nd Frame n­th Frame 44ms/46.4ms Note: Oscillator Frequency=480 or 455kHz 7. CARRIER WAVEFORM The following is the carrier waveform diagram. A bit modulates 10 carrier waveforms. pulses

1 Bit

a= 8.3µ s/8.76µ s Note: Oscillator Frequency=480 or 455kHz

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 7 of 12 TYPICAL APPLICATION CIRCUIT

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 8 of 12 CHIP TOPOGRAPHY 22 21 20 19 18 17 987654 size: 1.96 x 2.07mm2 PAD COORDINATES (Unit: µ m) No. Symbol X Y No. Symbol X Y 1 P1 ­904.75 ­122.00 13 P13 906.00 54.50 2 P2 ­904.75 ­258.25 14 P14 906.00 154.00 3 P3 ­904.75 ­709.00 15 P15 906.00 362.50 4 P4 ­450.25 ­851.25 16 P16 906.00 571.00 5 P5 ­200.25 ­851.25 17 P17 739.00 854.75 6 P6 80.75 ­851.25 18 P18 530.50 854.75 7 P7 220.75 ­851.25 19 P19 322.00 854.75 8 P8 501.75 ­851.25 20 P20 113.50 854.75 9 P9 641.75 ­851.25 21 P21 ­564.75 854.75 10 P10 906.00 ­615.50 22 P22 ­773.25 854.75 11 P11 906.00 ­475.50 23 P23 ­904.75 248.00 12 P12 906.00 ­194.50 24 P24 ­857.00 12.00 Note: The original point of the coordinate is the die center.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 9 of 12 PCB WIRE LAYOUT SCHEMATIC Transmitting tube output ground line The transmitting tube ground line and IC ground line should layout separated or overstriking ground line. The above IC only use to hint, not to specified. Note: * In wire layout, the power filter capacitor should near to IC. * In wire layout, should avoid power line and ground line too long. * Recommended infrared transmit unit and IC ground line should layout separated, or overstriking lines. * The e mitter of triode connect 1¡ resistor at least.

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 10 of 12 PACKAGE OUTLINE SDIP­24­300­2.54 UNIT: mm 7.62 0.25±0.05 4.36MAX3.00MIN 6.40±0.25 SOP­24­375­1.27 UNIT: mm 15.34±0.25 13.97 1.27 0.40 3.10MAX 0.25±0.05

HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:2.2 2005.12.15 Http: www.silan.com.cn Page 11 of 12 HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken:

  • Persons at a work bench should be earthed via a wrist strap.
  • Equipment cases should be earthed.
  • All tools used during assembly, including soldering tools and solder baths, must be earthed.
  • MOS devices should be packed for dispatch in antistatic/conductive containers.