SC23R01 SILAN | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 6
Technical content
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 1 of 7 8KBIT CONTACTLESS IC CARD
DESCRIPTION
SC23R01 is a smart card module utilizing CMOS EEPROM technology. It is a multiapplication functionality smart card with 1024 bytes EEPROM memory. Its embedded crypto and communication modules can protect the system from any kind of tampering and make it attractive in ticketing applications.
FEATURES
- 1024 X 8 bit EEPROM; * Operating frequency: 13.56MHz; baud rate: 106Kbit/s; * Contactless transmission of data and not need external power supply; * Operating distance: up to 10cm; * High security data transmission; * 16 independence sectors which support manifold applications; * For some key hierarchy system, each sector has two secret keys; * Customer definable access conditions for each memory block; * Arithmetic logic function; * High credible EEPROM controller, write endurance100000 cycles, data retention of 10 years; * Comply to the ISO/IEC14443 type A.
ORDERING INFORMATION
SC23R01T01002 Gold bump
APPLICATIONS
- used for ticketing syste m with IC card. BLOCK DIAGRAM
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 2 of 7 PIN CONFIGURATION RF2 RF1 XO A2 FUNCTION DESCRIPTION 1. RF interface and read/write device
1.1 Request ˄REQ STD/ALL˅
The communication protocol of SC23R01 is complied with the ISO14443A. When the card is positioned in the proximity of the read/write device (RWD), the RWD sends the REQ STD/ALL command to confirm whether the card is SC23R01.
1.2 Anticollision loop
When there are several cards in the operating rang of the RWD, the anticollision algorithm selects one card for further transaction. The unselected card return to the standby mode and wait for a new request command. In this course, it will return the serial number of the card.
1.3 Select card
Select the serial number of the selected card, the card returns the answer to select code (=08H). 1.4 3 Pass authentication After selecting the card, the RWD specifies the memory location which needs access, and uses the corresponding key for 3 pass authentication. After authenticating successfully, all memory operations are encrypted. (for selecting another sector, the key should be authenticated again) .
1.5 Memory operations
After authentication, the following operation may be performed: Read: read block. Write: write block. Decrement: decrease the content of a block and store the result in a data register. Incre ment: increase the content of a block and store the result in a data register. Transfer: write the content of data register to a value block. Restore: read the content of the value block to the data register. Halt: set the card in the halt mode. The operation flow chart:
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 3 of 7 2. Instruction Commands Code(hex) Request standby card 26 Request all the cards in the operating range 52 Anticollision 93 Select card 93 Authentication key A 60 Authentication key B 61 Read 30 Write A0 Increment C1 Decrement C0 Restore C2 Transfer B0 Halt 50 3. Data integrity In the contactless communication, the following measures ensure the data transmission: l anticollision l 16 bits CRC error correction for each frame
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 4 of 7 l parity bits for each byte l bit count checking l bit coding to distinguish between “ 1” , “ 0” or no information l channel monitoring(protocol sequence and bit stream analysis) 4. Security SC23R01 provides high security: three pass authentication is before read/write operation; each card has different serial number, ; transfer encrypted data and key protection. The secret key of the card is protected and cannot be read, which only the user knows and can amend it . The EEPROM is divided into 16 sectors, and each sector is with different key, user can set the key according to different sector (with multiapplications in one card). The RW D specifies the sector to be accessed only by verifying the key A or B. 5. Memory configuration and access condition The 8 k bits EEPROM is organized in 16 sectors with 4 blocks of 16 bytes each sector. Mem ory map: The block 3 of each sector contains the secret key A (6 bytes), access control condition (4 bytes) and secret key B(6 bytes), which is a specific block , other three blocks are data blocks; but the block 0 of the sector 0 used for store manufacture code and serial number, it is solidified and only readable. The data blocks can be configured two applications: read/write blocks and value blocks; the read/write block is used for store data, direct read and write; the value block is used for initialization, increment, decrement and value reading for direct control of the stored value. Block 3 configuration:
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 5 of 7 Access control of block 3 is as follows: Key A Key A Access Control Access Control Key B Key B Remark C1X3 C2X3 C3X3 Read Write Read Write Read Write 0 0 0 Never KEY A KEY A Never KEY A KEY A Key B m ay be read 0 1 0 Never Never KEY A Never KEY A Never Key B m ay be read 1 0 0 Never KEY B KEY A|B Never Never KEYB 1 1 0 Never Never KEY A|B Never Never Never 0 0 1 Never KEY A KEY A KEY A KEY A KEY A Key B m ay be read, transfer configuration 0 1 1 Never KEY B KEY A|B KEY B Never KEY B 1 0 1 Never Never KEY A|B KEY B Never Never 1 1 1 Never Never KEY A|B Never Never Never Note: KEYA|B indicates secret key A or key B; never denotes no condition implement. Data block storage control: C1XY C2XY C3XY Read Write Increment Decr, Transfer, Restore 0 0 0 KEY A|B1 KEY A|B1 KEY A|B1 KEY A|B1 0 1 0 KEY A|B1 Never Never Never 1 0 0 KEY A|B1 KEY B1 Never Never 1 1 0 KEY A|B1 KEY B1 KEY B1 KEY A|B1 0 0 1 KEY A|B1 Never Never KEY A|B1 0 1 1 KEY B1 KEY B1 Never Never 1 0 1 KEY B1 Never Never Never 1 1 1 Never Never Never Never Note: if key B can be read in the sector trailer, then it cannot be as key authentication(all grey line in above table). If the RWD tries to authenticate any blocks with key B using gray line, the card will refuse any operation for memory after authentication.
HANGZHOU SILAN MICROELECTRONICS CO.,LTD REV:1.1 2006.10.31 Http: www.silan.com.cn Page 6 of 7 PACKAGE OUTLINE XOA2 UNIT: mm MODULE HANDLING DESCRIPTION (ADVICE)
- The substrate material of the card is PVC of 6 layers (Inlay 2 layers).
- Antenna material: monocrystal Cu (enameled wire); antenna coil: 5 loops; linear diameter:Φ 0.13mm; inside diameter: 44x75mm; outside diameter: 45 x76mm; the module and antenna adopt bonding technology.
- The winding of the antenna coil makes the inductance to be 5.3~5.5µ +ѽҏ in order to match the antenna with the module and make sure it will m eet the requirement of resonance frequency and induction distance. HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken:
- Persons at a work bench should be earthed via a wrist strap.
- Equipment cases should be earthed.ҏ
- All tools used during assembly, including soldering tools and solder baths, must be earthed.
- MOS devices should be packed for dispatch in antistatic/conductive containers.