SBLF1030CT GE | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
SCHOTTKY ISOLATED PLASTIC RECTIFIER Reverse Voltage - 30 and 40 Volts Forward Current - 10.0 Amperes
FEATURES
¨ Isolated plastic package has Underwriters Laboratory Flammability Classifications 94V-0 ¨ Metal silicon junction, majority carrier conduction ¨ Low power loss,high efficiency ¨ High current capability, low forward voltage drop ¨ High surge capacity ¨ For use in low voltage, high frequency inverters, free wheeling, and polarity protection applications ¨ Guardring for overvoltage protection ¨ High temperature soldering guaranteed: 250¡C/10 seconds, 0.25" (6.35mm) from case MECHANICAL DATA Case: JEDEC ITO-220AB fully overmolded plastic body Terminals: Lead solderable per MIL-STD-750, Method 2026 Polarity: As marked Mounting Position: Any Mounting Torque: 5 in. - lbs max. Weight: 0.08 ounce, 2.24 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25¡C ambient temperature unless otherwise specified. SYMBOLS SBLF1030CT SBLF1040CT UNITS Maximum repetitive peak reverse voltage V RRM 30 40 Volts Maximum RMS voltage V RMS 21 28 Volts Maximum DC blocking voltage V DC 30 40 Volts Maximum average forward rectified current at TC=95¡C I(AV) 10.0 Amps Peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 175.0 Amps Maximum instantaneous forward voltage per leg at 5.0A (NOTE 1) VF 0.55 Volts Maximum instantaneous reverse current at T C=25¡C 0.5 rated DC blocking voltage (NOTE 1) TC=100¡C IR 50.0 mA Typical thermal resistance (NOTE 2) RQJC 5.0 ¡C/W Operating and storage temperature range T J, TSTG -40 to +125 ¡C RMS Isolation voltage from terminals to heatsink 4500 (NOTE 3) with RH ² 30% V ISOL 3500 (NOTE 4) Volts 1500 (NOTE 5) NOTES: (1) Pulse test: 300ms pulse width, 1% duty cycle (2) Thermal resistance from junction to case per leg (3) Clip mounting (on case), where lead does not overlap heatsink with 0.110Ó offset. (4) Clip mounting (on case), where leads do overlap heatsink. (5) Screw mounting with 4-40 screw, where washer diameter is £ 4.9 mm (0.19Ó). ITO-220AB Dimensions in inches and (millimeters) 0.060 (1.52) 0.405 (10.27) 0.383 (9.72) 0.676 (17.2) 0.171 (4.35) 0.600 (15.5) 0.580 (14.5) 0.560 (14.22) 0.530 (13.46) 0.037 (0.94) 0.027 (0.69) 0.140 (3.56) 0.130 (3.30) 0.350 (8.89) 0.330 (8.38) 0.188 (4.77) 0.172 (4.36) 0.110 (2.80) 0.100 (2.54) 0.131 (3.39) 0.122 (3.08) 0.110 (2.80) 0.100 (2.54) 0.022 (0.55) 0.014 (0.36) 0.105 (2.67) 0.095 (2.41) 0.205 (5.20) 0.195 (4.95) PIN 1 PIN 3 PIN 2 1 3 PIN DIA.DIA. NEW PRODUCT NEW PRODUCT NEW PRODUCT 2/17/99
0.01 0.1 0.1 1.0 10 100 100 1,000 4,000 0 50 100 1500 2.5 7.5 12.5 0.01 0.1 1 10.0 100 0.1 1.0 10.0 100 0 20 40 60 80 100 0.001 0.01 0.1 FIG. 1 - FORWARD CURRENT DERATING CURVE CASE TEMPERATURE, ¡C AVERAGE FORWARD CURRENT, AMPERES FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT NUMBER OF CYCLES AT 60 HZ PEAK FORWARD SURGE CURRENT, AMPERES FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER LEG FIG. 4 - TYPICAL REVERSE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT, AMPERES INSTANTANEOUS REVERSE CURRENT, MILLIAMPERES INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF REVERSE VOLTAGE, VOLTS t, PULSE DURATION, sec. TJ=75¡C TJ=25¡C TJ=25¡C TJ=125¡C TJ = 25¡C f=1.0 MHz Vsig=50mVp-p PULSE WIDTH = 300ms 1% DUTY CYCLE RESISTIVE OR INDUCTIVE LOAD TJ=125¡C FIG. 6 - TYPICAL TRANSIENT THERMAL IMPEDANCE PER LEG TRANSICENTTHERMAL IMPEDANCE, °C/W TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1.0 RATINGS AND CHARACTERISTIC CURVES SBLF1030CT AND SBLF1040CT