S524A40X11 SAMSUNG | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 16

Technical content

Serial EEPROM for Low Power Data Sheet 1 - 1 OVERVIEW The S524A40X11/40X21/40X41/60X81/60X51 serial EEPROM has a 1,024/2,048/4,096/8,192/16,384 - bit capacity, supporting the standard I 2 C™ - bus serial interface. It is fabricated using Samsung’s most advanced CMOS technology. It has been developed for lo w power and low voltage applications (1.8 V to 5.5 V). One of its major feature is a hardware - based write protection circuit for the entire memory area. Hardware - based write protection is controlled by the state of the write - protect (WP) pin. Using one - page write mode, you can load up to 16 bytes of data into the EEPROM in a single write operation. Another significant feature of the S524A40X11/40X21/40X41/60X81/60X51 is its support for fast mode and standard mode.

FEATURES

  • Two - wire seri al interface
  • Automatic word address increment EEPROM
  • 1K/2K/4K/8K/16K - bit (128/256/512/1,024/2,048 - byte) storage area
  • 16 - byte page buffer
  • Typical 3 ms write cycle time with auto - erase function
  • Hardware - based write protection for the entire EEPROM (using the WP pin)
  • EEPROM programming voltage generated on chip
  • 1,000,000 erase/write cycles
  • 100 years data retention Operating Characteristics
  • Operating voltage — 1.8 V to 5.5 V
  • Operating current — Maximum write current: < 3 mA at 5.5 V — Maximum read current: < 200 µA at 5.5 V — Maximum stand - by current: < 1 µA at 5.5 V
  • Operating temperature range — – 25°C to + 70°C (commercial) — – 40°C to + 85°C (industrial)
  • Operating clock frequencies — 100 kHz at standard mode — 400 kHz at fast mode
  • Electrostatic discharge (ESD) — 5,000 V (HBM) — 500 V (MM) Packages
  • 8 - pin DIP, SOP, and TSSOP

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 2 Start/Stop Logic Slave Address Comparator Word Address Pointer Row decoder EEPROM Cell Array 128 x 8 bits 256 x 8 bits 512 x 8 bits 1024 x 8 bits 2048 x 8 bits HV Generation Timing Control Control Logic Column Decoder Data Register D OUT and ACK SCL WP SDA Figure 1 - 1. S524A40X11/40X21/40X41/60X81/60X51 Block Diagram

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 3 S524A40X11/40X21/ 40X41/60X81/60X51 V CC WP SCL SDA A0 A1 A2 V SS NOTE: The S524A40X11/40X21/40X41/60X81/60X51 is available in 8-pin DIP, SOP, and TSSOP package. Figure 1 - 2. Pin Assignme nt Diagram Table 1 - 1. S524A40X11/40X21/40X41/60X81/60X51 Pin Descriptions Name Type Description Circuit Type A0, A1, A2 Input Input pins for device address selection. To configure a device address, these pins should be connected to the V CC or V SS of the device. These pins are internally pulled down to V SS . V SS – Ground pin. – SDA I/O Bi - directional data pin for the I 2 C - bus serial data interface. Schmitt trigger input and open - drain output. An external pull - up resistor must be connected to V CC. Typical values for this pull - up resistor are 4.7 k Ω (100 kHz) and 1 k Ω (400 kHz). SCL Input Schmitt trigger input pin for serial clock input. 2 WP Input Input pin for hardware write protection control. If you tie this pin to V CC, the write function is disabled to protect previously written data in the entire memory; if you tie it to V SS , t he write function is enabled. This pin is internally pulled down to V SS . V CC – Single power supply. – NOTE : See the following page for diagrams of pin circuit types 1, 2, and 3.

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 5 FUNCTION DESCRIPTION I2 C - BUS INTERFACE The S524A40X11/40X21/40X41/60X81/60X51 supports the I 2 C - bus serial interface data transmission protocol. The two - wire bus consists of a serial data line (SDA) and a serial clock line (SCL). The SDA and the SCL lines must be connected to V CC by a pull - up resistor that is located som ewhere on the bus. Any device that puts data onto the bus is defined as the “transmitter” and any device that gets data from the bus is the “receiver.” The bus is controlled by a master device which generates the serial clock and start/stop conditions, controlling bus access. Using the A0, A1 , and A2 input pins, up to eight S524A40X11/40X21 (four S524A40X41, two for S524A60X81, one for S524A60X51) devices can be connected to the same I 2 C - bus as slaves (see Figure 1 - 6). Both the master and slaves can operate as transmitter or receiver, but the master device determines which bus operating mode would be active. SDA Bus Master (Transmitter/ Receiver) MCU S524A40X21 Tx/Rx A0 A1 A2 Slave 1 To V CC or V SS S524A40X21 Tx/Rx A0 A1 A2 Slave 2 To V CC or V SS S524A40X21 Tx/Rx A0 A1 A2 Slave 3 To V CC or V SS S524A40X21 Tx/Rx A0 A1 A2 Slave 8 To V CC or V SS R V CC R V CC SCL NOTES: 1. The A0 does not affect the device address of the S524A40X41. 2. The A0, A1 do not affect the device address of the S524A60X81. 3. The A0, A1, and A2 do not affect the device address of the S524A60X51. Figure 1 - 6. Typical Configuration (16 Kbits of Memory on the I 2 C - Bus)

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 6 I2 C - BUS PROTOCOLS Here are several rules for I 2 C - bus transfers: — A new data transfer can be initiated only when the bus is currently not busy. — MSB is always transferred first in transmitting data. — During a data transfer, the data line (SDA) must remain stable whenever the clock line (SCL) is High. The I2 C - bus interface supports the following communication protocols:

  • Bus not busy : The SDA and the SCL lines remain High level when the bus is not active.
  • Start condition : Start condition is initiated by a High - to - Low transition of the SDA line while SCL remains High level. All bus commands must be preceded by a start condition.
  • Stop condition : A stop condition is initiated by a Low - to - High transition of the SDA line while SCL remains High level. All bus operations must be completed by a stop condition (see Figure 1 - 7). SCL SDA Start Condition Data or ACK Valid Data Change ~~~~ Stop Condition Figure 1 - 7. Data Transmission Sequence
  • Data valid : Following a start condition, the data becomes valid if the data line remains stable for the duration of the High period of SCL. New data must be put onto the bus while SCL is Low. Bus timing is one clock pulse per data bit. The number of data bytes to be transferred is determined by the master device. The total number of bytes that can be transferred in one operation is theoretically unlimited.
  • ACK (Acknow ledge) : An ACK signal indicates that a data transfer is completed successfully. The transmitter (the master or the slave) releases the bus after transmitting eight bits. During the 9th clock, which the master generates, the receiver pulls the SDA line low to acknowledge that it successfully received the eight bits of data (see Figure 1 - 8). But the slave does not send an ACK if an internal write cycle is still in progress. In data read operations, the slave releases the SDA line after transmitting 8 bits o f data and then monitors the line for an ACK signal during the 9th clock period. If an ACK is detected, the slave will continue to transmit data. If an ACK is not detected, the slave terminates data transmission and waits for a stop condition to be issued by the master before returning to its stand - by mode.

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 7 Master SCL Line Data from Transmitter ACK ACK from Receiver Bit 9Bit 1 Figure 1 - 8. Acknowledge Response From Receiver

  • Slave Address : After the master initiates a Start condition, it must output the address of the device to be accessed. The m ost significant four bits of the slave address are called the “device identifier”. The identifier for the S524A40X11/40X21/40X41/60X81/60X51 is “1010B”. The next three bits comprise the address of a specific device. The device address is defined by the state of the A0, A1 and A2 pins. Using this addressing scheme, you can cascade up to eight S524A40X11/40X21 or four S524A40X41 or two S524A60X81 or one S524A60X51 on the bus (see Table 1 - 2 below). The b1 for S524A40X41 or the b1, b2 for S524A60X81 or the b1, b2, b3 for S524A60X51 are used by the master to select which of the blocks of internal memory (1 block = 256 words) are to be accessed. The bits are in effect the most significant bits of the word address.
  • Read/Write : The final (eighth) bit of the slave address defines the type of operation to be performed. If the R /W bit is “1”, a read operation is executed. If it is “0”, a write operation is executed. Table 1 - 2. Slave Device A ddressing Device Device Identifier Device Address R/ W Bit b7 b6 b5 b4 b3 b2 b1 b0 S524A40X11/40X2 1 0 1 0 A2 A1 A0 R/ W S524A40X41 1 0 1 0 A2 A1 B0 R/ W S524A60X81 1 0 1 0 A2 B1 B0 R/ W S524A60X51 1 0 1 0 B2 B1 B0 R/ W NOTE: The B2, B1, B0 correspond to the MSB of the memory array address word.

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 8 BYTE WRITE OPERATION In a complete byte write operation, the master transmits the slave address, word address, and one data byte to the S524A40X11/40X21/40X41/60X81/60X51 slave device (see Figure 1 - 9). Slave AddressStart Word Address Data Stop A C K A C K A C K Figure 1 - 9. Byte Write Operation Following the Start condition, the master sends the device identifier (4 bits), the device address (3 bits), and an R /W bit set to “0” onto the bus. Then the addressed S524A40X11/40X21/40X41/60X81/60X51 generates an ACK and waits for the next byte. The next byte to be transmitted by the master is the word address. This 8 - bit address is written into the word address pointer of the S524A40X11/40X21/40X41/60X81/60X51. When the S524A40X11/40X21/40X41/60X8 1/60X51 receives the word address, it responds by issuing an ACK and then waits for the next 8 - bit data. When it receives the data byte, the S524A40X11/40X21/40X41/60X81/60X51 again responds with an ACK. The master terminates the transfer by generating a Stop condition, at which time the S524A40X11/40X21/40X41/60X81/60X51 begins the internal write cycle. While the internal write cycle is in progress, all S524A40X11/40X21/40X41/60X81/60X51 inputs are disabled and the S524A40X11/40X21/40X41/60X81/60X51 does n ot respond to additional requests from the master.

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 9 PAGE WRITE OPERATION The S524A40X11/40X21/40X41/60X81/60X51 can also perform 16 - byte page write operation. A page write operation is initiated in the same way as a byte write operation. However, instead of finishing the write operation after the first data byte is transferred, the master can transmit up to 15 additional bytes. The S524A40X11/40X21/40X41/60X81/60X51 responds with an ACK each time it receives a complete byte of data (see Figure 1 - 10). Slave Address Word Address (n)Start A C K A C K Data (n) A C K A C K Data ( ≤ n + 15) Stop A C K Figure 1 - 10. Page Write Operation The S524A40X11/40X21/40X41/60X81/60X51 automatically increments the word address pointer each time it receives a complete data byte. When one byte has been received, the internal word address pointer increments to the next address and the next data byte can be received. If the master transmits more than 16 bytes before it generates a stop condition to end the page write operation, the S524A40X11/40X21/40X41/60X81/60X51 word address pointer value “r olls over” and the previously received data is overwritten. If the master transmits less than 16 bytes and generates a stop condition, the S524A40X11/40X21/40X41/60X81/60X51 writes the received data to the corresponding EEPROM address. During a page write operation, all inputs are disabled and there is no response to additional requests from the master until the internal write cycle is completed.

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 10 POLLING FOR AN ACK S IGNAL When the master issues a stop condition to initiate a write cycle, the S524A40X11/40 X21/40X41/60X81/60X51 starts an internal write cycle. The master can then immediately begin polling for an ACK from the slave device. To poll for an ACK signal in a write operation, the master issues a start condition followed by the slave address. As long as the S524A40X11/40X21/40X41/60X81/60X51 remains busy with the write operation, no ACK is returned. When the S524A40X11/40X21/40X41/60X81/60X51 completes the write operation, it returns an ACK and the master can then proceed with the next read or write operation (see Figure 1 - 11). Send Write Command Send Stop Condition to Initiate Write Cycle Send Start Condition Send Slave Address with R/ W bit = "0" Start Next Operation ACK = "0" ? Yes No Figure 1 - 11. Master Polling for an ACK Signal from a Slave Device

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 12 RANDOM ADDRESS BYTE READ OPERATION Using random read operations, the master can access any memory location at any time. Before it issues the slave address with the R /W bit set to “1”, the master must first perform a “dummy” write operation. This operation is performed in the following steps: 1. The master first issues a Sta rt condition, the slave address, and the word address to be read. (This step sets the internal word address pointer of the S524A40X11/40X21/40X41/60X81/60X51 to the desired address.) 2. When the master receives an ACK for the word address, it immediately re - issues a start condition followed by another slave address, with the R /W bit set to “1”. 3. The S524A40X11/40X21/40X41/60X81/60X51 then sends an ACK and the 8 - bit data stored at the desired address. 4. At this point, the master does not acknowledge th e transmission, but generates a stop condition instead. 5. In response, the S524A40X11/40X21/40X41/60X81/60X51 stops transmitting data and reverts to its stand - by mode (see Figure 1 - 13). Slave Address Word AddressStart A C K A C K Slave Address A C K N O A C K StopStart Data (n) Figure 1 - 13. Random Address Byte Read Operation

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 13 SEQUENTIAL READ OPER ATION Sequential read operations can be performed in two ways: as a series of current address reads or as random address reads. The first data is sent in the same way as the previous read mode used on the bus. The next time, h owever, the master responds with an ACK, indicating that it requires additional data. The S524A40X11/40X21/40X41/60X81/60X51 continues to output data for each ACK it receives. To stop the sequential read operation, the master does not respond with an ACK, but instead issues a Stop condition. Using this method, data is output sequentially with the data from address “n” followed by the data from “n+1”. The word address pointer for read operations increments all word addresses, allowing the entire EEPROM to be read sequentially in a single operation. After the entire EEPROM is read, the word address pointer “rolls over” and the S524A40X11/40X21/40X41/60X81/60X51 continues to transmit data for each ACK it receives from the master (see Figure 1 - 14). Slave Address Data (n)Start A C K A C K N O A C K Data (n + x) A C K Figure 1 - 14. Sequential Read Operation

S524A40X1 1/40X21/40X41/60X81/ 60X51 SERIAL EEPROM DATA SHEET 1 - 14 ELECTRICAL DATA Table 1 - 3. Absolute Maximum Ratings (T A = 25 °C) Parameter Symbol Conditions Rating Unit Supply voltage V CC – – 0.3 to + 7.0 V Input voltage V IN – – 0.3 to + 7.0 V Output volta ge V O – – 0.3 to + 7.0 V Operating temperature T A – – 40 to + 85 °C Storage temperature T STG – – 65 to + 150 °C Electrostatic discharge V ESD HBM 5000 V MM 500 Table 1 - 4. D.C. Electrical Characteristics Parameter Symbol Conditions Min Typ Max Unit Input low voltage V IL SCL, SDA, A0, A1, A2 – – 0.3 V CC V Input high voltage V IH 0.7 V CC – – V Input leakage current ILI V IN = 0 to V CC – – 10 µA Output leakage current ILO V O = 0 to V CC – – 10 µA Output low voltage V OL IOL = 3 mA, V CC = 2.5 V – – 0.4 V Supply current Write ICC1 V CC = 5.5 V, 400 kHz – – 3 mA ICC2 V CC = 1.8 V, 100 kHz – – 1 Read ICC3 V CC = 5.5 V, 400 kHz – – 0.2 ICC4 V CC = 1.8 V, 100 kHz – – 60 µA Stand - by current ICC5 V CC = SDA = SCL = 5.5 V, all other inputs = 0 V – – 1 µA ICC6 V CC = SDA = SCL = 1.8 V, all other inputs = 0 V – – 1

DATA SHEET S524A40X 11/40X21/40X41/60X81 /60X51 SERIAL EEPRO M 1 - 15 Table 1 - 4. D.C. Electrical Characteristics (Continued) Parameter Symbol Conditions Min Typ Max Unit Input capacitance C IN 25 °C, 1MHz, V CC = 5 V, V IN = 0 V, A0, A1, A2, SCL and WP pin – – 10 pF Input/output capacitance C I/O 25 °C, 1MHz, V CC = 5 V, V I/O = 0 V, SDA pin – – 10 Table 1 - 5. A.C. Electrical Characteristics Parameter Symbol Conditions V CC = 1.8 to 5.5 V (Standard Mode) V CC = 2.5 to 5.5 V (Fast Mode) Unit Min Max Min Max External clock frequency F CLK – 0 100 0 400 kHz Clock high time tHIGH – 4 – 0.6 – µs Clock low time tLOW – 4.7 – 1.3 – Rising time tR SDA, SCL – 1 – 0.3 Falling time tF SDA, SCL – 0.3 – 0.3 Start condition hold time tHD:STA – 4 – 0.6 – Start condition setup time tSU:STA – 4.7 – 0.6 – Data input hold time tHD:DAT – 0 – 0 – Data input setup time tSU:DAT – 0.25 – 0.1 – Stop condition setup time tSU:STO – 4 – 0.6 – Bus free time tBUF Before new transmission 4.7 – 1.3 – Data output valid from clock low (note) Noise spike width tSP – – 100 – 50 ns Write cycle time tWR – – 5 – 5 ms NOTE : When acting as a transmitter, the S524A40X11/40X21/40X41/60X81/60X51 must provide an internal minimum delay time to bridge the undefined period (minimum 300 ns) of the falling edge of SCL. This is required to avoid unintended generation of a start or stop condition.