RP40-121.5SG_06 RECOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 5
Technical content
Features
Selection Guide 12V, 24V and 48V Input Types Part Number Input Output Output Input (4) Efficiency(5) Capacitive(6) Range Voltage Current Current Load max. VDC VDC mA mA % µF RP40-121.5SG 9-18 1.5 8000 1351 78 45000 RP40-121.8SG 9-18 1.8 8000 1579 80 37700 RP40-122.5SG 9-18 2.5 8000 2137 82 27000 RP40-123.3SG 9-18 3.3 8000 2750 84 21000 RP40-1205SG 9-18 5 8000 4065 86 13600 RP40-1212SG 9-18 12 3333 4065 86 2360 RP40-1215SG 9-18 15 2666 4015 87 1510 RP40-241.5SG 18-36 1.5 8000 649 81 45000 RP40-241.8SG 18-36 1.8 8000 759 83 37700 RP40-242.5SG 18-36 2.5 8000 1029 85 27000 RP40-243.3SG 18-36 3.3 8000 1325 87 21000 RP40-2405SG 18-36 5 8000 1961 89 13600 RP40-2412SG 18-36 12 3333 2048 88 2360 RP40-2415SG 18-36 15 2666 1985 89 1510 RP40-481.5SG 36-75 1.5 8000 321 82 45000 RP40-481.8SG 36-75 1.8 8000 375 84 37700 RP40-482.5SG 36-75 2.5 8000 508 86 27000 RP40-483.3SG 36-75 3.3 8000 655 88 21000 RP40-4805SG 36-75 5 8000 969 90 13600 RP40-4812SG 36-75 12 3333 1000 89 2360 RP40-4815SG 36-75 15 2666 992 89 1510 RP40-1212DG 9-18 ±12 ±1800 4444 85 ±1200 RP40-1215DG 9-18 ±15 ±1400 4321 85 ±750 RP40-2412DG 18-36 ±12 ±1800 2169 87 ±1200 RP40-2415DG 18-36 ±15 ±1400 2108 87 ±750 RP40-4812DG 36-75 ±12 ±1800 1084 87 ±1200 RP40-4815DG 36-75 ±15 ±1400 1054 87 ±750 for Triple Output continued on next page The RP40-xxxxG Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards.
Description
July-2006 275www.recom-international.com
Selection Guide 12V, 24V and 48V Input Types POWERLINE DC/DC-Converter RP40-S_D_TG Series Part Number Input Output Output Input (4) Efficiency(5) Capacitive(6) Range Voltage Current Current Load max. VDC VDC mA mA % µF RP40-123.305DG 9-18 3.3 / 5 4A / 4A (total 8A) (15) 3416 85 11000 / 6800 RP40-243.305DG 18-36 3.3 / 5 4A / 4A (total 8A) (15) 1689 86 11000 / 6800 RP40-483.305DG 36-75 3.3 / 5 4A / 4A (total 8A) (15) 823 88 11000 / 6800 RP40-123.312TG 9-18 3.3 / ±12 6000 / ±400 3063 84 13000 / ±330 RP40-123.315TG 9-18 3.3 / ±15 6000 / ±300 3000 84 13000 / ±110 RP40-120512TG 9-18 5 / ±12 6000 / ±400 4024 86 6800 / ±330 RP40-120515TG 9-18 5 / ±15 6000 / ±300 3963 86 6800 / ±110 RP40-243.312TG 18-36 3.3 / ±12 6000 / ±400 1512 85 13000 / ±330 RP40-243.315TG 18-36 3.3 / ±15 6000 / ±300 1481 85 13000 / ±110 RP40-240512TG 18-36 5 / ±12 6000 / ±400 1989 87 6800 / ±330 RP40-240515TG 18-36 5 / ±15 6000 / ±300 1958 87 6800 / ±110 RP40-483.312TG 36-75 3.3 / ±12 6000 / ±400 747 86 13000 / ±330 RP40-483.315TG 36-75 3.3 / ±15 6000 / ±300 732 86 13000 / ±110 RP40-480512TG 36-75 5 / ±12 6000 / ±400 982 88 6800 / ±330 RP40-480515TG 36-75 5 / ±15 6000 / ±300 967 88 6800 / ±110 Derating-Graph (Ambient Temperature) /MT49/MT50/MT53 /MT55/MT53 /MT53/MT48 /MT50/MT53 /MT48 /MT49/MT48/MT48 /MT65/MT109/MT98/MT105/MT101/MT110/MT116/MT32/MT84/MT101/MT109/MT112/MT101/MT114/MT97/MT116/MT117/MT114/MT101/MT32/MT82/MT97/MT110/MT103/MT101/MT32/MT40/MT176/MT67/MT41 /MT45/MT50/MT53/MT45/MT49/MT48 /MT48/MT53/MT48/MT54/MT48 /MT56/MT48 /MT57/MT48 /MT49/MT48/MT48 /MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT80/MT111/MT119/MT101/MT114/MT32/MT40/MT37/MT41 /MT78/MT97/MT116/MT117/MT114/MT97/MT108/MT32/MT67/MT111/MT110/MT118/MT101/MT99/MT116/MT105/MT111/MT110 /MT45/MT52/MT48 /MT55/MT48 RP40-4805SG Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at info@recom-development.at July-2006 www.recom-international.com276
DC/DC-Converter RP40-S_D_TG Series /MT57/MT50 /MT56/MT51 /MT56/MT50 /MT73/MT110/MT112/MT117/MT116/MT32/MT86/MT111/MT108/MT116/MT97/MT103/MT101/MT32/MT40/MT86/MT41 /MT51/MT54 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT40/MT37/MT41 /MT56/MT52 /MT56/MT53 /MT56/MT54 /MT56/MT55 /MT56/MT56 /MT56/MT57 /MT57/MT49 /MT57/MT48 /MT52/MT50 /MT53/MT52 /MT54/MT54/MT52/MT56 /MT55/MT50/MT54/MT48 /MT55/MT53 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT86/MT83/MT32/MT73/MT110/MT112/MT117/MT116/MT32/MT86/MT111/MT108/MT116/MT97/MT103/MT101 /MT56/MT48 /MT55/MT53 /MT54/MT53 /MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT76/MT111/MT97/MT100/MT32/MT40/MT65/MT41 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT40/MT37/MT41 /MT56/MT50 /MT56/MT52 /MT56/MT54 /MT56/MT56 /MT57/MT48 /MT57/MT50 /MT57/MT52 /MT55/MT48 /MT49/MT53 /MT56/MT51/MT52 /MT54/MT55/MT50 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT86/MT83/MT32/MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT76/MT111/MT97/MT100 RP40-4805SG RP40-4805SG Typical Characteristics Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 9-18VDC 24V nominal input 18-36VDC 48V nominal input 36-75VDC Under Voltage Lockout 12V input DC-DC ON 9VDC DC-DC OFF 8VDC 24V input DC-DC ON 17.8VDC DC-DC OFF 16VDC 48V input DC-DC ON 36VDC DC-DC OFF 34VDC Input Filter (see Note 13) L-C Type Input Voltage Variation dv/dt (Complies with ETS300 132 part 4.4) 5V/ms max Input Surge Voltage (100 ms max.) 12V Input 36VDC 24V Input 50VDC 48V Input 100VDC Input Reflected Ripple (nominal Vin and full load see Note 3) 40mAp-p Start Up Time (nominal Vin and constant resistor load) 25ms typ. Remote ON/OFF (see Note 7) DC-DC ON Open or 3.5V < Vr < 12V ( Positive logic ) DC-DC OFF Short or 0V < Vr < 1.2V Remote OFF input current Nominal input 2.5mA Output Power 40W max. Output Voltage Accuracy (full Load and nominal Vin) Single & Dual ±1% Triple Main ±1% Auxiliary ±5% Voltage Adjustability ±10% Minimum Load Single and Dual Positive 0% Dual and Triple 10% of full load Line Regulation (low line, high line at full load) Single & Dual ±0.5% Triple Main ±1% Triple Auxiliary ±5% continued on next page July-2006 277www.recom-international.com
Specifications (typical at nominal input and 25°C unless otherwise noted) POWERLINE DC/DC-Converter RP40-S_D_TG Series Load Regulation (10% to 100% full load see Note 9 and 10) Single ±0.5% Dual ±1% Triple Main ±2% Auxiliary ±5% Cross Regulation (Note 11) Triple Main ±1% Dual / Triple Auxiliary ±5% Ripple and Noise (20MHz bandwith) Single 1.5, 1.8, 2.5, 3.3, 5V 50mVp-p (Measured with a 1004pF/50V MLCC) Single 12, 15V 75mVp-p Dual 12V 120mVp-p Dual 15V 150mVp-p RP40-xx3.305DG 100mVp-p (see Note 12) RP40-xxxxxxTG 50 / 75mVp-p Temperature Coefficient ±0.02%/°C max. Transient Response (25% load step change) 300µs Zener diode clamp (only single) 5V 6.2V 12V 15V 15V 18V Over Load Protection (% of full load at nominal Vin) 150% max. Short Circuit Protection Hiccup, automatic recovery Efficiency see „Selection Guide“ table Isolation Voltage 1600VDC min. Isolation Resistance 1 GΩ min. Isolation Capacitance 1000pF max. Operating Frequency (see Note 14) 300kHz typ. Approved to Safety Standards Single,Triple UL 1950, EN60950 Dual EN60950 Operating Temperature Range -40°C to +85°C(with derating) Maximum Case Temperature 100°C Storage Temperature Range -55°C to +105°C Thermal Impedance (see Note 8) Natural convection 9.2°C/Watt Heat Sink with 20LFM 8.5°C/Watt Heat Sink with 500LFM 2.8°C/Watt Thermal Shock MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel plated copper Base Material Non-conductive black plastic FR4 Potting Material Epoxy (UL94-V0) Conducted Emissions (see Note 16) EN55022 Level A Radiated Emissions EN55022 Level A ESD EN61000-4-2 Perf. Criteria 2 Radiated Immunity EN61000-4-3 Perf. Criteria 2 Fast Transient EN61000-4-4 Perf. Criteria 2 Surge EN61000-4-5 Perf. Criteria 2 Conducted Immunity EN61000-4-6 Perf. Criteria 2 Weight 60g Dimensions 50.8 x 50.8 x 10.2mm MTBF (see Note 2) 1398 x 103 hours July-2006 www.recom-international.com278
/MT53 /MT52 /MT50/MT56/MT46/MT50/MT48 /MT53/MT48/MT46/MT56/MT48 /MT50 /MT51 /MT52/MT53/MT46/MT55/MT48 /MT49/MT50/MT46/MT55/MT48 /MT49/MT53/MT46/MT50/MT48 /MT66/MT111/MT116/MT116/MT111/MT109/MT32/MT86/MT105/MT101/MT119 /MT49/MT48/MT46/MT50/MT48 /MT100/MT105/MT97/MT46 /MT49/MT46/MT48 /MT49 /MT50/MT46/MT53 /MT49/MT53/MT46/MT51/MT48 /MT50/MT48/MT46/MT51/MT48 /MT53/MT46/MT49/MT48 /MT54 /MT55 /MT56 /MT57 /MT55/MT46/MT54 /MT53/MT46/MT49/MT48 /MT53/MT46/MT54 /MT48/MT46/MT55/MT48 /MT53/MT48/MT46/MT56/MT48 RP40-S_D_TG Series Notes : POWERLINE DC/DC-Converter Package Style and Pinning (mm) /MT51/MT114/MT100/MT32/MT97/MT110/MT103/MT108/MT101 /MT112/MT114/MT111/MT106/MT101/MT99/MT116/MT105/MT111/MT110 Pin Pitch Tolerance ±0.35 mm Pin Connections Pin # Single Dual Triple Dual Positive 1 +Vin +Vin +Vin +Vin 2 -Vin -Vin -Vin -Vin
3 CTRL CTRL CTRL CTRL
4 NC No Pin +Aux 3.3V 5 -Sense (Note1) +Vout Com 3.3V RTN(Com) 6 +Sense (Note1) Com -Aux NC 7 +Vout Com +Vout NC 8 -Vout -Vout -Vout(Com) 5V
9 Trim Trim NC 5V RTN(Com)
NC = No Connection /MT84/MT114/MT105/MT109/MT32/MT85/MT112 /MT82/MT85 /MT84/MT114/MT105/MT109/MT32/MT68/MT111/MT119/MT110 /MT82/MT68 /MT56/MT40/MT56/MT41 /MT57/MT40/MT57/MT41 /MT57/MT40/MT57/MT41 /MT55/MT40/MT53/MT41 External Output Trimming Output can be externally trimmed by using the method shown below. ( ) for dual output trim 1. Maximum output deviation is 10% inclusive of remote sense and trim. If remote sense is not being used, the +Vsense should be connected to its corresponding +OUTPUT and likewise the sense should be connected to its corresponding -OUTPUT 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12µH. 12µH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input. 8. Heat sink is optional and P/N: 7G-0026A. 9. The triple output required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load cond ition will not damage these devices,however they may not meet all listed specification. 10. Load regulation for triple output: Main output(V1):10 to 100% with 10% to 100% balanced on auxiliaries. Auxiliary outputs(V2 and V3):10% to 100% balanced on all outputs. 11.Cross regulation for triple output: Main output 100% load, auxiliary 100%,other auxiliary25% to 100%. Auxiliary outputs(V2 and V3):main output 100% load, auxiliary 100%, other auxiliary 25% to 100% or main output 25%,auxiliary 25%,other auxiliary 25% to 100%. 12.The models of RP40-XX3.305DG are specified with a 1uF ceramic output capacitors. 13.An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V/24V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90m Ω. 14.Operating frequency for dual output: master (5Vo) 300KHz slave (3.3Vo) 500KHz. 15.Any condition of dual output (3.3V/5V) rated Iout current, not to exceed 8A of total output currents. The product safety app roval pending. 16.See application notes for EMI-filtering. July-2006 279www.recom-international.com