RP30-121.5SE RECOM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Selection Guide 12V, 24V and 48V Input Types Part Number Input Output Output Input (4) Efficiency(5) Capacitive(6) Range Voltage Current Current Load max. VDC VDC mA mA % µF RP30-121.5SE 9-18 1.5 6000 1014 78 85800 RP30-121.8SE 9-18 1.8 6000 1169 81 65000 RP30-122.5SE 9-18 2.5 6000 1582 83 33000 RP30-123.3SE 9-18 3.3 6000 2037 85 19500 RP30-1205SE 9-18 5 6000 3012 87 10200 RP30-1212SE 9-18 12 2500 2976 88 3240 RP30-1215SE 9-18 15 2000 2976 88 1100 RP30-241.5SE 18-36 1.5 6000 493 80 85800 RP30-241.8SE 18-36 1.8 6000 580 82 65000 RP30-242.5SE 18-36 2.5 6000 780 84 33000 RP30-243.3SE 18-36 3.3 6000 1010 86 19500 RP30-2405SE 18-36 5 6000 1490 88 10200 RP30-2412SE 18-36 12 2500 1470 89 3300 RP30-2415SE 18-36 15 2000 1470 89 1100 RP30-481.5SE 36-75 1.5 6000 244 81 85800 RP30-481.8SE 36-75 1.8 6000 290 83 65000 RP30-482.5SE 36-75 2.5 6000 390 85 33000 RP30-483.3SE 36-75 3.3 6000 500 87 19500 RP30-4805SE 36-75 5 6000 740 89 10200 RP30-4812SE 36-75 12 2500 730 90 3300 RP30-4815SE 36-75 15 2000 730 90 1100 RP30-1212DE 9-18 ±12 ±1250 3012 87 ±1020 RP30-1215DE 9-18 ±15 ±1000 3012 87 ±675 RP30-2412DE 18-36 ±12 ±1250 1488 88 ±1020 RP30-2415DE 18-36 ±15 ±1000 1488 88 ±675 RP30-4812DE 36-75 ±12 ±1250 744 88 ±1020 RP30-4815DE 36-75 ±15 ±1000 744 88 ±675 The E-Series of DC/DC Converters are fully certified to EN 60950: 2000. This makes them ideal for all Telecom and safety applications where approved isolation is required. They also meet UL 1950 and CSA 950 standards.
Description
www.recom-international.com 241April-2005 Derating-Graph (Ambient Temperature) POWERLINE DC/DC-Converter RP30-S_DE Series /MT49/MT50/MT53 /MT55/MT53 /MT53/MT48 /MT50/MT53 /MT48 /MT49/MT48/MT48 /MT65/MT109/MT98/MT105/MT101/MT110/MT116/MT32/MT84/MT101/MT109/MT112/MT101/MT114/MT97/MT116/MT117/MT114/MT101/MT32/MT82/MT97/MT110/MT103/MT101/MT32/MT40/MT176/MT67/MT41 /MT45/MT50/MT53/MT45/MT49/MT48 /MT48 /MT53/MT48 /MT54/MT48 /MT56/MT48 /MT57/MT48 /MT49/MT48/MT48 /MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT80/MT111/MT119/MT101/MT114/MT32/MT40/MT37/MT41 /MT78/MT97/MT116/MT117/MT114/MT97/MT108/MT32/MT67/MT111/MT110/MT118/MT101/MT99/MT116/MT105/MT111/MT110 /MT45/MT52/MT48 /MT55/MT48 /MT54/MT50/MT176/MT67 /MT49/MT50/MT53 /MT55/MT53 /MT53/MT48 /MT50/MT53 /MT48 /MT49/MT48/MT48 /MT65/MT109/MT98/MT105/MT101/MT110/MT116/MT32/MT84/MT101/MT109/MT112/MT101/MT114/MT97/MT116/MT117/MT114/MT101/MT32/MT82/MT97/MT110/MT103/MT101/MT32/MT40/MT176/MT67/MT41 /MT45/MT50/MT53/MT45/MT49/MT48 /MT48 /MT53/MT48/MT54/MT48/MT55/MT48 /MT56/MT48 /MT57/MT48 /MT49/MT48/MT48 /MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT80/MT111/MT119/MT101/MT114/MT32/MT40/MT37/MT41 /MT78/MT97/MT116/MT117/MT114/MT97/MT108/MT32/MT67/MT111/MT110/MT118/MT101/MT99/MT116/MT105/MT111/MT110 /MT45/MT52/MT48 /MT55/MT49/MT176/MT67 RP30-4805SE RP30-4805SEW With Heat Sink /MT57/MT51 /MT56/MT53 /MT56/MT52 /MT56/MT50 /MT73/MT110/MT116/MT112/MT117/MT116/MT32/MT86/MT111/MT108/MT116/MT97/MT103/MT101/MT32/MT40/MT86/MT41 /MT51/MT54 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT40/MT37/MT41 /MT56/MT54 /MT56/MT55 /MT56/MT56 /MT56/MT57 /MT57/MT48 /MT57/MT49 /MT57/MT50 /MT56/MT51 /MT52/MT48 /MT54/MT48 /MT54/MT53/MT52/MT53 /MT53/MT48/MT53/MT53 /MT55/MT48 /MT55/MT53 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT86/MT83/MT32/MT73/MT110/MT112/MT117/MT116/MT32/MT86/MT111/MT108/MT116/MT97/MT103/MT101 /MT57/MT50 /MT56/MT48 /MT55/MT56 /MT55/MT52 /MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT76/MT111/MT97/MT100/MT32/MT40/MT65/MT41 /MT49 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT40/MT37/MT41 /MT56/MT52 /MT56/MT53 /MT56/MT54 /MT56/MT55 /MT56/MT56 /MT56/MT57 /MT57/MT48 /MT55/MT54 /MT50/MT53 /MT54/MT51/MT52 /MT69/MT102/MT102/MT105/MT99/MT105/MT101/MT110/MT99/MT121/MT32/MT86/MT83/MT32/MT79/MT117/MT116/MT112/MT117/MT116/MT32/MT76/MT111/MT97/MT100 RP30-4805SE RP30-4805SE Typical Characteristics Specifications (typical at nominal input and 25°C unless otherwise noted) Input Voltage Range 12V nominal input 9-18VDC 24V nominal input 18-36VDC 48V nominal input 36-75VDC Under Voltage Lockout 12V input DC-DC ON 9VDC DC-DC OFF 8VDC 24V input DC-DC ON 17.8VDC DC-DC OFF 16VDC 48V input DC-DC ON 36VDC DC-DC OFF 33VDC Input Filter (see note 1) L-C Type Input Voltage Variation dv/dt (Complies with ETS300 132 part 4.4) 5V/ms max Input Surge Voltage (100 ms max.) 12V Input 36VDC 24V Input 50VDC 48V Input 100VDC Input Reflected Ripple (nominal Vin and full load) 30mAp-p Start Up Time (nominal Vin and constant resistor load) 25ms typ. Remote ON/OFF (see note 7) DC-DC ON Open or 3.5V < Vr < 12V DC-DC OFF Short or 0V < Vr < 1.2V Remote OFF input current Nominal input 2.5mA continued on next page Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical customer service at inf o@recom-development.at
242 www.recom-international.comApril-2005 Specifications (typical at nominal input and 25°C unless otherwise noted) POWERLINE DC/DC-Converter RP30-S_DE Series Output Power 30W max. Output Voltage Accuracy (full Load and nominal Vin) ±1% Voltage Adjustability ±10% Minimum Load Single & Dual 0% Line Regulation (LL-HL at full load) Single ±0.2% Dual ±0.5% Load Regulation (25% to 100% FL) Single ±0.5% Dual ±1% Cross Regulation (Note 9) ±5% Ripple and Noise (20MHz bandwith) Single 1.5, 1.8, 2.5, 3.3, 5V 50mVp-p (Measured with a 1004pF/50V MLCC) Single 12, 15V 75mVp-p Dual 5, 12, 15V 100mVp-p Temperature Coefficient ±0.02%/°C, max. Transient Response (25% load step change) 300µS Zener diode clamp (only single) 5V 6.2V 12V 15V 15V 18V Over Load Protection (% of full load at nominal Vin) 150% typ Short Circuit Protection Hiccup, automatic recovery Efficiency see „Selection Guide“ table Isolation Voltage 1.600VDC min. Isolation Resistance 109 Ω min. Isolation Capacitance 1000pF max. Operating Frequency 300kHz typ. Approved to Safety Standards UL 1950, EN60950 Operating Temperature Range -40°C to +85°C(with derating) Maximum Case Temperature +100°C Storage Temperature Range -55°C to +105°C Over Temperature Protection 115°C typ. Thermal Impedance Natural convection 10°C/Watt Natural convection with Heat Sink 8.24°C/Watt Thermal Shock MIL-STD-810D Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z Relative Humidity 5% to 95% RH Case Material Nickel-Coated copper Base Material Non-conductive black plastic Potting Material Epoxy (UL94-V0) Conducted Emissions EN55022 Class A Radiated Emissions EN55022 Class A ESD EN61000-4-2 Perf. Criteria 2 Radiated Immunity EN61000-4-3 Perf. Criteria 2 Fast Transient EN61000-4-4 Perf. Criteria 2 Surge EN61000-4-5 Perf. Criteria 2 Conducted Immunity EN61000-4-6 Perf. Criteria 2 continued on next page
www.recom-international.com 243April-2005 Specifications (typical at nominal input and 25°C unless otherwise noted) POWERLINE DC/DC-Converter RP30-S_DE Series Weight 48g Dimensions 50.8 x 40.6 x 10.2mm MTBF (see note 2) 1.535 x 106 Hours 1. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current fo r 48V/24V models. RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90m Ω. 2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). 3. Simulated source impedance of 12uH. 12uH inductor in series with +Vin. 4. Maximum value at nominal input voltage and full load of standard type. 5. Typical value at nominal input voltage and full load. 6. Test by minimum Vin and constant resistor load. 7. The ON/OFF control pin voltage is referenced to negative input 8. Heat sink is optional and P/N: 7G-0011A. 9. See application notes for EMI-filtering. Notes : Package Style and Pinning (mm) /MT53 /MT53/MT48/MT46/MT56/MT48 /MT53/MT46/MT49/MT48 /MT49/MT53/MT46/MT50/MT48 /MT49/MT55/MT46/MT56/MT48 /MT52/MT48/MT46/MT54/MT48 /MT50 /MT52 /MT52/MT53/MT46/MT55/MT48 /MT49/MT50/MT46/MT55/MT48/MT49/MT48/MT46/MT50/MT48 /MT49/MT55/MT46/MT56/MT48 /MT49/MT48/MT46/MT50/MT48 /MT56 /MT55 /MT54 /MT49 /MT53/MT46/MT54 /MT49/MT48/MT46/MT50/MT48 /MT100/MT105/MT97/MT46 /MT49/MT46/MT48 /MT66/MT111/MT116/MT116/MT111/MT109/MT32/MT86/MT105/MT101/MT119 /MT51/MT114/MT100/MT32/MT97/MT110/MT103/MT108/MT101 /MT112/MT114/MT111/MT106/MT101/MT99/MT116/MT105/MT111/MT110 Pin Pitch Tolerance ±0.35 mm Pin Connections Pin # Single Dual 1 +Vin +Vin 2 -Vin -Vin
4 CTRL CTRL
5 No Pin +Vout
8 Trim Trim
/MT84/MT114/MT105/MT109/MT32/MT85/MT112 /MT82/MT85 /MT84/MT114/MT105/MT109/MT32/MT68/MT111/MT119/MT110 /MT82/MT68 /MT55/MT40/MT55/MT41 /MT56/MT40/MT56/MT41 /MT56/MT40/MT56/MT41 /MT54/MT40/MT53/MT41 External Output Trimming Output can be externally trimmed by using the method shown below. ( ) for dual output trim