RP08-1212DA

RP08-A RECOM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 7

Technical content

Features

• 2:1 Wide Input Voltage Range
• 1.6kVDC Isolation
• UL Certified
• Efficiency up to 87%
• Low Profile, 10.2mm Height
• Over Current Protection

8 Watt

Single & Dual Output RP08-A Selection Guide Part Number Input Output Output Input(1) Efficiency (1) Max. Capacitive Voltage Range Voltage Current Current typ. Load(2) [VDC] [VDC] [mA] [mA] [%] [µF] RP08-123.3SA(3) 9-18 3.3 2000 688 80 3300 RP08-1205SA(3) 9-18 5 1500 753 83 1600 RP08-1212SA(3) 9-18 12 666 757 88 350 RP08-1215SA(3) 9-18 15 533 766 87 240 RP08-243.3SA(3) 18-36 3.3 2000 344 80 3300 RP08-2405SA(3) 18-36 5 1500 377 83 1600 RP08-2412SA(3) 18-36 12 666 387 86 350 RP08-2415SA(3) 18-36 15 533 392 85 240 RP08-483.3SA(3) 36-75 3.3 2000 172 80 3300 RP08-4805SA(3) 36-75 5 1500 188 83 1600 RP08-4812SA(3) 36-75 12 666 194 86 350 RP08-4815SA(3) 36-75 15 533 194 86 240 RP08-1205DA(3) 9-18 ±5 ±800 803 83 ±1000 RP08-1212DA(3) 9-18 ±12 ±333 766 87 ±160 RP08-1215DA(3) 9-18 ±15 ±267 785 85 ±100 RP08-2405DA(3) 18-36 ±5 ±800 407 82 ±1000 RP08-2412DA(3) 18-36 ±12 ±333 387 86 ±160 RP08-2415DA(3) 18-36 ±15 ±267 393 85 ±100 RP08-4805DA(3) 36-75 ±5 ±800 196 85 ±1000 RP08-4812DA(3) 36-75 ±12 ±333 191 87 ±160 RP08-4815DA(3) 36-75 ±15 ±267 192 87 ±100 UL60950-1 Certified Input Voltage Output Voltage Single or Dual Notes: Note3: no suffix for standard package (DIP24), add suffix „SMD“ for SMD package Package(3) Model Numbering Ordering Examples RP08-4805SA/SMD = 48V Input, 5V Output, Single, SMD Package RP08-1205DA = 12V Input, 5V Output, Dual, DIP24 Package Notes: Note1: Maximum value at nominal input voltage and full load. Note2: Test by minimum Vin and constant resistor load.

Parameter Condition Min. Typ. Max. Input Voltage Range nom. Vin = 12V nom. Vin = 24V nom. Vin = 48V 9VDVC 18VDC 36VDC 12VDC 24VDC 48VDC 18VDC 36VDC 75VDC Under Voltage Lockout (UVLO) none Input Filter Pi-Type Input Reflected Ripple Current nominal Vin and full load 20mAp-p Input Surge Voltage Vin = 12V, 100ms max. Vin = 24V, 100ms max. Vin = 48V, 100ms max. 36VDC 50VDC 100VDC Start-up time Power up Remote ON/OFF 700ms 5ms Operating Frequency Range 270kHz 300kHz 330kHz Minimum Load(4) full load 10% Ripple and Noise 20MHz Bandwidth 50mVp-p Remote ON/OFF(5) Positive Logic DC-DC ON DC-DC OFF Open or 3.0V < Vr < 12V Short or 0V < Vr < 1.2V Input current of Remote pin (CTRL) DC-DC OFF 2.5mA DC-DC ON -0.5mA +0.5mA continued on next page PD-2 REV.: 1/2016 www.recom-power.com DC/DC Converter Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted RP08-A Series Efficiency vs. Output Current Efficiency vs. Input Voltage Notes: Note4: The RP08 series requires a minimum of 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage these devices, however they may not meet all listed specification. Note5: The ON/OFF control pin voltage is referenced to -Vin pin. 9Vin 12Vin 18Vin Efficiency [%] Output Current [%] 20 30 40 50 60 70 80 90 100 Efficiency [%] Input Voltage [VDC] 11 12 14 16 1810 13 15 17 RP08-1205SA

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted REGULATIONS Parameter Condition Value Output Voltage Accuracy ±1.0% max. Line Voltage Regulation low line to high line ±0.2% max. Load Voltage Regulation Single (0% to 100% load) DIP24 SMD ±0.5% ±1% Dual (0% to 100% load) DIP24, SMD ±1% Cross Regulation asymmetrical 25%<>100% load ±5% Transient Response recovery time 25% load step change 200μs typ. RP08-A Series Efficiency vs. Output Current Efficiency vs. Output Current Efficiency vs. Input Voltage Efficiency vs. Input Voltage PD-3REV.: 1/2016www.recom-power.com Efficiency [%] Input Voltage [VDC] 22 24 28 32 3620 26 30 34 Efficiency [%] Input Voltage [VDC] 44 48 56 66 7540 52 60 72 RP08-4805SA RP08-2405SA 18Vin 24Vin 36Vin Efficiency [%] Output Current [%] 20 40 60 80 100 30 50 70 90 36Vin 48Vin 75Vin Efficiency [%] Output Current [%] 20 40 60 80 100 30 50 70 90

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted RP08-A Series ENVIRONMENTAL Parameter Condition Value Operating Temperature Range without derating with derating -40°C to +80°C -40°C to +100°C Maximum Case Temperature +100°C Temperature Coefficient ±0.02%/°C max. Thermal Impedance Natural convection (20LFM) 20°C/Watt typ. Operating Humidity non-condensing 5% - 95% RH Shock MIL-STD-810F Vibration MIL-STD-810F MTBF MIL-HDBK-217F BELLCORE TR-NWT-000332(7) 3543 x 103 hours 3165 x 10³ hours Notes: Note7: BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment). Note8: Derating graphs are valid only for the shown part numbers. If you need detailed derating-information about a part-number not shown here please contact our technical support service at techsupportAT@recom-power.com. -40 60 80 10040200-20 100 Ambient Temperature [°C] Output Power [%] Derating Graph(8) RP08-1212SA PROTECTIONS Parameter Condition Value Short Circuit Protection (SCP) continuous, automatic recovery Over Load Protection (OLP) % of Iout rated 150% typ. Isolation Voltage DIP24 I/P to O/P I/P (O/P) to case 1.6kVDC/1 minute 1.6kVDC/1 minute SMD I/P to O/P I/P (O/P) to case 1.6kVDC/1 minute 1.0kVDC/1 minute Isolation Resistance 500VDC 1GΩ min. Isolation Capacitance 300pF max. Notes: Note6: This power module is not internally fused. An input line fuse must always be used. PD-4 REV.: 1/2016 www.recom-power.com

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted RP08-A Series SAFETY AND CERTIFICATIONS Certificate Type Report / File Number Standard UL General Safety E196683 UL60950-1 1st Ed.: 2003 C22.2 No. 60950 1st. Ed.: 2003 EMC Compliance Condition Standard / Criterion EMI Standard(9) with external filter EN55022, Class A or B ESD Radiated Immunity Fast Transient(10) Surge Conducted Immunity Air ±8kV and Contact ±6kV

10 V/m

±2kV ±1kV 10 Vr.m.s EN61000-4-2, Criteria A EN61000-4-3, Criteria A EN61000-4-4, Criteria A EN61000-4-5, Criteria A EN61000-4-6, Criteria A Input Input DC DC Fuse +VIN +VOUT -VOUT -VIN LOAD DC DC Fuse +VIN +VOUT COM -VOUT -VIN LOADLOAD Input Input DC DC Fuse C2C1 +VIN +VOUT -VOUT -VIN LOAD +VOUT COM -VOUT LOADLOAD DC DC Fuse C2C1 +VIN +VOUT -VOUT -VIN Input Input DC DC Fuse C2C1 +VIN +VOUT -VOUT -VIN LOAD +VOUT COM -VOUT LOADLOAD DC DC Fuse C2C1 +VIN +VOUT -VOUT -VIN Input Input DC DC Fuse +VIN +VOUT -VOUT -VIN LOAD DC DC Fuse +VIN +VOUT COM -VOUT -VIN LOADLOAD EMI Filtering Class A EMI Filtering Class B MODEL C1 C2/C3 RP08-12xxS_D RP08-12xxS_D/SMD 4.7μF/25V

1210 MLCC

1206 MLCC

RP08-24xxS_D RP08-24xxS_D/SMD N/A 1000pF/2kV RP08-48xxS_D RP08-48xxS_D/SMD N/A 1000pF/2kV RP08-12xxS_D RP08-12xxS_D/SMD 4.7μF/25V

1210 MLCC N/A 1000pF/2kV

CMC :325μH ref: WE 744290321 ref.: CMC-06 RP08-24xxS_D RP08-24xxS_D/SMD 6.8μF/50V

1812 MLCC N/A 1000pF/2kV

CMC: 325μH ref: WE 744290321 ref.: CMC-06 RP08-48xxS_D RP08-48xxS_D/SMD 2.2μF/100V

1812 MLCC

2.2μF/100V CMC: 325μH ref: WE 744290321 ref.: CMC-06 Notes: Note9: The standard modues meet EMI Class A or Class B with external components, see filter suggestions below. Note10: An external input filter capacitor is required if the module has to meet EN61000-4-4, EN61000-4-5. The suggested capacitor: Nippon chemi-con KY series 200μF/100V. PD-5REV.: 1/2016www.recom-power.com

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted RP08-A Series PD-6 REV.: 1/2016 www.recom-power.com DIMENSIONS and PHYSICAL CHARACTERISTICS Parameter Type Value Material Case Base Potting Nickel coated copper Non-conductive black plastic Epoxy (UL94-V0) SMD 31.8 x 20.3 x 10.2mm 32.0 x 20.5 x 11.2mm SMD 16g 18g SMD Dimension Drawing (mm) Pin Connections Pin # Single Dual

1 Ctrl Ctrl

9 NC Com

11 NC -Vout

Pin Pitch Tolerance ±0.25mm Pin Dimension Tolerance ±0.1mm XX.X ± 0.5mm XX.XX ± 0.25mm NC = No Connection 11.0 25.4 11.220.3 0.50 1.60 2.40 32.0 27.94 20.3 25.40 10.162.54 2.541.0 x 0.50 1 4 5 9 10 11 1232 24 21 20 Bottom View Top View 16 15 14 132223 Pin area DIP Dimension Drawing (mm) Pin Connections Pin # Single Dual Pin Pitch Tolerance ±0.25mm Pin Dimension Tolerance ±0.1mm XX.X ± 0.5mm XX.XX ± 0.25mm NC = No Connection 20.3 3.80 10.2 31.8 Ø0.5 20.32 2.0 2 3 Bottom View 9 11 23 22 16 14 5.08 15.24 2.54

Specifications measured at Ta = 25°C, nominal input voltage, full load otherwise noted RP08-A Series PD-7REV.: 1/2016www.recom-power.com PACKAGING INFORMATION Parameter Type Value Packaging Quantity 7pcs. Storage Temperature Range -55°C to +125°C Storage Humidity 5% - 95% RH The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications.