RC1206FR-0710RL

DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
PDF pages: 20

Technical content

AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Single-channel isolated gate driver IC with adjustable DESAT and so ft-o ff About this document Scope and purpose The gate driver evaluation board EVAL-1ED3491Mx12M with the 1ED3491MU12M or 1ED3491MC12M gate driver IC demonstrates the functionality, adjustment possibilities, and key features of the Infineon EiceDRIVER™ 1ED-X3 Analog gate driver ICs. The boards contain a short circuit protection which is described in more detail in the key feature section of this document. Details about the EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M or 1ED3491MC12M can be found at our product pages at https://www.infineon.com/gdisolated or the product search. The design of the EVAL-1ED3491Mx12M was performed with respect to the environmental conditions described in this document. The design was tested as described in this document, but not qualified regarding manufacturing, lifetime or over the full range of operating conditions. The boards provided by Infineon are not subject to full production test. Evaluation boards are not subject to the same procedures as regular products regarding Returned Material Analysis (RMA), Process Change Notification (PCN) and Product Discontinuation (PD). Evaluation boards are intended to be used under laboratory conditions and by trained specialists only. Intended audience

Engineers who want to learn how to use the Infineon EiceDRIVER ™
Experienced design engineers designing circuits with Infineon EiceDRIVER ™, IGBT and CoolSiC™ SiC MOSFET
Design engineers designing power electronic devices, like inverters Table of contents

1.7 Adjusting the negative gate voltage value for CoolSiC

AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Application Note Please read the Important Notice and Warnings at the end of this document v1.0 www.infineon.com/gdisolated 2020-05-27

Gate driver IC information

Features

600 V, 650 V, 900 V, and 1200 V IGBTs, SiC and Si MOSFETs
40 V absolute maximum output supply voltage
±3 A, ±6 A, and ±9 A typical sinking and sourcing peak output current
Separate source and sink outputs for hard switching and with active Miller clamp/clamp driver
Adjustment pins for parameter configuration from input side
Precise V CEsat detection (DESAT) with fault output and adjustable filter time and leading edge blanking time with resistor at ADJB pin
Adjustable IGBT soft turn-off after desaturation detection with resistor at ADJA pin
Operation at high ambient temperature up to 125 °C with over-temperature shut down at 160 °C (±10 °C)
Tight IC-to-IC propagation delay matching ( tPDD,max = 30 ns)
Undervoltage lockout protection with hysteresis for input and output side with active shut-down
High common-mode transient immunity CMTI = 200 kV/µs
Small space-saving DSO-16 fine-pitch package with large creepage distance (>8 mm)
Safety certification - UL 1577 recognized (planned) with VISO,test = 6840 V (rms) for 1 s, VISO = 5700 V (rms) for 60 s - IEC 60747-17/VDE 0884-11 approval (planned) with VIORM = 1.4 kV (peak, reinforced)
Evaluation board available EVAL-1ED3491MX12M Potential applications
Industrial motor drives - compact, standard, premium, servo drives
Solar inverters
UPS systems
Welding
Commercial and agricultural vehicles (CAV)
Commercial air-conditioning (CAC)
High-voltage isolated DC-DC converters
Isolated switch mode power supplies (SMPS) PG-DSO-16 AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Gate driver IC information Application Note 2 v1.0 2020-05-27

Product type Output current CLAMP type1) Isolation class Marking OPN 1ED3431MC12M 3 A (typ) CLAMP reinforced 3431MC12 coming soon 1ED3461MC12M 6 A (typ) CLAMPDRV reinforced 3461MC12 coming soon 1ED3491MC12M 9 A (typ) CLAMPDRV reinforced 3491MC12 coming soon 1ED3431MU12M 3 A (typ) CLAMP UL 1577 3431MU12 1ED3431MU12MXUMA1 1ED3461MU12M 6 A (typ) CLAMPDRV UL 1577 3461MU12 1ED3461MU12MXUMA1 1ED3491MU12M 9 A (typ) CLAMPDRV UL 1577 3491MU12 1ED3491MU12MXUMA1

1 Electrical description

The evaluation board EVAL-1ED3491Mx12M is intended for the product feature evaluation of the Infineon EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M or 1ED3491MC12M in an application circuit. The key elements of the board and the product are listed below:

Evaluation board in half-bridge configuration with two gate driver ICs to drive power switches such as IGBTs, Si MOSFETs, and CoolSiC™ SiC MOSFETs. The switch type can be freely chosen as seen in Figure 1
Galvanically isolated power supply for both secondary sides
Resistors marking for the adjustable functions of each gate driver IC Figure 1 EVAL-1ED3491Mx12M top view The board has a size of 85 x 55 x 15 mm3 without any power switch assembled. This board is best suited for so-called double-pulse testing and evaluation. For continuous operation, the thermal and load power should be taken into consideration. It is also recommended to add an additional high- voltage DC blocking capacitor at the high-voltage supply. The low-voltage interface can be controlled by a pulse generator, a microcontroller or any other digital circuits. The adjustable DESAT filters can be adjusted by replacing the resistor attached to the ADJB pin of each gate driver IC. Similarly, the soft-off current after DESAT detection can be adjusted by replacing the resistor attached to the ADJA pin of each gate driver IC. The evaluation board has a power supply for the primary and secondary sides implemented. This allows the user to evaluate the gate driver by only supplying a 15 V input voltage. Jumper J40 can be used to adjust the primary side operation voltage, between 5 V and 3.3 V. In case the user wants to use its own power supply,

1 Please refer to CLAMP output types for circuit connection to avoid damage to the gate driver IC

AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 3 v1.0 2020-05-27

jumper J70 can be used to disable the power supply for the primary and secondary sides. This will be discussed in more details in the following chapters. Different LEDs across the board are used to visually feedback the state of the board, showing the presence of the supply voltages and the state of the fault pins. This will be discussed in more details in the following chapters.

1.1 Absolute maximum ratings, operating conditions, and supply

The selected components on this evaluation board as well as the gate driver ICs have maximum ratings and operating conditions to avoid damaging the individual parts and the evaluation board overall. Table 1 Absolute maximum ratings Pin/parameter name Abs. max. rating Unit Note P15VP -0.3 … 20 V Input supply voltage of the power supply stage (referenced to SGND) VCC -0.3 … 6.5 V Primary side supply voltage (referenced to SGND).2) RDYC -0.3 … 6.5 V Input/output digital signal FL T# -0.3 … 6.5 V Input/output digital signal IN_HS -0.3 … 6.5 V Input digital signal IN_LS -0.3 … 6.5 V Input digital signal VCC2H,VCC2L -0.3 … 40 V Isolated secondary positive supply with reference to GND2H/GND2L2) VCC2H,VCC2L -0.3 … 40 V Overall secondary supply voltage with reference to VEE2H/VEE2L2) VEE2H,GEE2L -40 … 0.3 V Isolated secondary negative supply with reference to GND2H/GND2L2) P1000VP -0.2 … 900 V Input, high-voltage supply reference to GND power terminal, for voltages above 42 V, special safety measures should be taken Phase peak current 30 A Phase peak output current for double pulse tests. Maximum current is only limited by the thermal capabilities of the PCB tpulse 100 µs maximum ON pulse length for double-pulse tests fsw 100 kHz maximum switching frequency for continuous operation, power dissipation should be considered This evaluation board is optimized for both 5 V and 3.3 V VCC supply voltage. Depending on the used input signals, by using jumper J40 (5V EN) the end user can select 5 V or 3.3 V operation. This will affect the input threshold values, which are referenced to VCC. It is recommended to use the board with the built-in power supply circuit. This provides a +15 V/-7 V supply voltage on the secondary sides for both upper and lower side gate drivers. In case a separate, external power supply is to be used, the built in power supply can be disabled by using the jumper J70 (ISO DIS).

2 Not to be used when power supply circuit is enabled

AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 4 v1.0 2020-05-27

Table 2 Recommended operating conditions and supply voltages for 5 V operation Pin name Min. Typ. Max. Unit Note P15VP 15.0 15.5 16.0 V Power supply input voltage VCC 4.9 5.0 5.1 V Gate driver IC primary side input voltage2) FL T# -0.1 VCC VCC1+ 0.1 V Input/output digital signal RDYC -0.1 VCC VCC1+ 0.1 V Input/output digital signal IN_HS -0.1 VCC VCC1+ 0.1 V Input digital signal IN_LS -0.1 VCC VCC1+ 0.1 V Input digital signal VCC2H,VCC2L 12 22 30 V Overall isolated secondary power supply as referenced to VEE2H/VEE2L2) GND2H,GND2L 0 7 15 V Gate reference supply pin as referenced to VEE2H/ VEE2L2) P1000VP 25 800 V Input, high voltage supply, for voltages above 42 V, special safety measures should be taken

1.2 Initial settings

The evaluation board comes preconfigured from assembly. The present DESAT leading edge blanking time is 1150 ns and the DESAT filter time is 2375 ns corresponding to the resistors R13 and R23 with a value of: 13.7 kΩ. The preset soft-off current for DESAT events is set to a typical value of 131 mA corresponding to the resistors R14 and R24 with a value of: 1.91 kΩ.

1.3 Start-up

In this chapter the prerequisites and power up sequence are described. This will allow the evaluation of the Infineon EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M in a half-bridge configuration. Prerequisites

Assemble suitable power switches in the sockets T50 and T60 at the location Q1 and Q2. E.g. IKW40N120H3 IGBTs or IMW120R030M1H CoolSiC™ SiC MOSFETs
Assemble an external high-voltage decoupling capacitor (> 100 µF) across the high voltage power terminal, X90-1 (P1000VP) and X90-3 (GND)
Have a low-voltage power supply for supplying the power supply circuit, capable of supplying 15 V, 100 mA (P15VP, SGND)
Have a high-voltage power supply for supplying the power stage between X90-1 ( P1000VP) and X90-3 (GND)
Have an inductive load for double-pulse testing
Have a signal generator for half-bridge operation or double-pulse testing
E96 resistor kit with 0805 1% values to adjust the DESAT and soft-off settings on the EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M In order to adapt the board to other applications or evaluation scenarios, resistor and capacitor values might require to be changed in order to optimize the evaluation boards for the desired scenarios.

AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 5 v1.0 2020-05-27

Select the input voltage operation, between 5 V or 3.3 V. Either close J40 (5V EN) for 5 V operation, or leave it open for 3.3 V operation. 2. Make sure J70 (ISO DIS) is open in order to have the built-in isolated power supply enabled. 3. Connect the PWM signals to the digital interface at connector X1, for the upper switch (IN-HS,GND) and lower switch (IN-LS,GND) 4. Connect one end of the inductive load to X90-2 (PHASE) and the other end according to the double-pulse requirements to either X90-1 (P1000VP) or X90-3 (GND) for low side or high side testing 5. Supply P15VP at the connector X40-2 with +15.5 V and connect the supply return, SGND, to connector X40-2. 6. The green LED D41 (15V_ok) will turn on signaling the input supply is present 7. The green LED D46 (VCC1_ok) will turn on signaling the primary side of the gate drivers is present. 8. The green LEDs D42 (FL T#) and D44 (RDYC) will turn on signaling the secondary sides of both chips have been properly supplied, no fault condition is detected by the gate driver ICs and the driver ICs are ready for operation 9. Connect the high voltage supply to connector X90-3 (GND) and X90-1 (P1000VP) 10. The board is now ready for double-pulse evaluation

1.4 Fault detection

The gate driver IC comes with adjustable DESAT filter times and soft-off current. The functionality and complete explanation of the settings are detailed in the product datasheet. This application note only covers the minimum information needed for evaluation and it is highly recommended to review the datasheet before designing with the gate driver IC.

1.4.1 DESAT protection with filter time and leading edge blanking time

The gate driver IC comes with desaturation protection aimed at protecting the external switch from destruction during short-circuit events. The simplified sequence for the desaturation protection is as following: 1. The voltage at the DESAT pin reaches the DESAT threshold level 2. The gate driver IC switches the external switch off, using the soft-off method 3. The gate driver IC pulls FL T# low to indicate the fault and latches the signal 4. The red LED D43 (FL T#) turns on and the green LED D44 (FL T#) turns off 5. The short-circuit event is cleared. Because the FL T# signal is shared between the FL T_N open drain output/input pins of both gate drivers. A DESAT or fault even on one of the gate drivers will automatically disable both gate drivers operation. In order to clear the fault, the RDYC signal has to be pulled down for at least tCLRMIN as described in the datasheet. As RDYC is attached to both gate driver ICs RDYC pin, both gate driver ICs will be cleared. Filter and leading edge blanking time adjustment The EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M comes with an adjustable DESAT leading edge blanking time, tDESATleb, and DESAT filter time, tDESATfilter by means of a resistor connected between pin ADJB and the primary side ground pin, GND1. By choosing one of the 16 values for the resistor, as shown in the table below, allows the user to select a suitable DESAT filter time setting for their application without the use of external RC filters. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 6 v1.0 2020-05-27

Table 3 DESAT filter timing ADJB adjustment DESAT filter time set up stopped 0 1 2 3 4 5 6 7 Resistance at ADJB to GND1 1.05 kΩ or tied to GND1 typ. tDESATleb inhibit gate driver operatio n 650 ns 650 ns 650 ns 650 ns 650 ns 650 ns 650 ns 650 ns typ. tDESATfilter 1575 ns 1775 ns 1975 ns 2375 ns 2775 ns 3175 ns 3575 ns 3975 ns Table 3 DESAT filter timing ADJB adjustment DESAT filter time set up 8 9 10 11 12 13 14 15 default Resistance at ADJB to GND1 or tied to VCC1 typ. tDESATleb 1150 ns 1150 ns 1150 ns 1150 ns 1150 ns 1150 ns 1150 ns 1150 ns 400 ns typ. tDESATfilter 3975 ns 3575 ns 3175 ns 2775 ns 2375 ns 1975 ns 1775 ns 1575 ns 225 ns For the lower side gate driver IC, the resistor connected to ADJB is R24. For the higher side gate driver IC, the resistor connected to ADJB is R14.

1.4.2 So ft turn-o ff current adjustment

During normal operation the gate driver IC always uses hard switch-off. In case a fault, or a forced turn-off by pulling RDYC low, the gate driver IC will turn-off the connected power switch using the soft-off function. The gate of the connected power device is discharged via the OFF pin by an internal current sinking circuit. This discharge current can be adjusted to a value, lower than the hard-off current used during normal operation. During an overcurrent event, such as short-circuit, the current in the circuit is mainly limited by the switch channel as the switch goes into saturation. Turning off such high currents with a hard-off event results, most of the times, due to the parasitic inductances in the power loop, into over-voltage conditions across the switch. This over-voltage could degrade or even damage the switch. By employing soft turn-off current functionality, the high overcurrent event is slowly turned off, reducing the overshoot voltage. Since the soft turn-off events are a one off occurrence after failures, the gate driver IC is designed to internally handle the extra power dissipation. The soft-off current source can be selected by changing the value of the resistance between pin ADJA and GND1 of the gate driver IC. Connecting the ADJA pin to VCC1 will inhibit the start-up sequence and disable the gate driver operation. By choosing one of the 16 values for the resistor, as shown in the table below, allows the user to select a suitable soft-off current setting for their application without the use of other external components. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 7 v1.0 2020-05-27

Table 4 So ft-o ff adjustment with ADJA So ft-o ff set up default 0 1 2 3 4 5 6 7 Resistance from ADJA to GND1 < 1.05 kΩ or tied to GND1 typ. ICSOFF 1ED3431M 146 mA 15 mA 29 mA 44 mA 58 mA 73 mA 87 mA 102 mA 116 mA typ. ICSOFF 1ED3461M 291 mA 29 mA 58 mA 87 mA 116 mA 146 mA 175 mA 204 mA 233 mA typ. ICSOFF 1ED3491M 437 mA 44 mA 87 mA 131 mA 175 mA 218 mA 262 mA 306 mA 349 mA Table 4 So ft-o ff adjustment with ADJA So ft-o ff set up 8 9 10 11 12 13 14 15 stopped Resistance from ADJA to GND1 tied to VCC1 typ. ICSOFF 1ED3431M 131 mA 146 mA 160 mA 175 mA 189 mA 204 mA 218 mA 233 mA inhibit gate driver operationtyp. ICSOFF 1ED3461M 262 mA 291 mA 320 mA 349 mA 379 mA 408 mA 437 mA 466 mA typ. ICSOFF 1ED3491M 393 mA 437 mA 480 mA 524 mA 568 mA 612 mA 655 mA 699 mA For the lower side gate driver IC, the resistor connected to ADJA is R23. For the higher side gate driver IC, the resistor connected to ADJA is R13

1.5 Adjusting the DESAT and so ft-o ff settings

The datasheet contains a detailed description of the DESAT and soft-off turn-off functions, including typical values and it is recommended to consult it before proceeding further with the adjustments and investigation of the gate driver. As mentioned earlier the EiceDRIVER™ 1ED-X3 Analog 1ED3491MU12M comes with adjustable DESAT leading edge blanking time and filter time and adjustable soft-off fault currents. During the start-up procedure, the gate driver IC reads the external resistor values from the ADJA and ADJB pins. These values and their linked parameters are stored within the gate driver IC until the next supply voltage drop- out. This ensures that during operation, any source of noise, will not influence these settings. Depending on the application, topology, control method and switches used, the DESAT protection might need to be adjusted to offer reliable protection of the power switches. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 8 v1.0 2020-05-27

1.5.1 DESAT leading edge blanking time and filter time options

Figure 2 Leading edge blanking time filters Figure 2 shows the three selectable leading edge blanking settings in relationship to the output signal of the gate driver. The power switched used in this example was in saturation for all three measurements. The tDESATleb,d = 400 ns option is only selectable with a tDESATfilter,def = 225 ns. For the leading edge blanking filter tDESATleb,s = 650 ns and tDESATleb,l = 1150 ns, eight different DESAT filter times can be selected, from 1575 ns to 3975 ns. Figure 3 DESAT filter times Figure 3 shows the eight different DESAT filter settings in relation to the gate driver IC OUT signal. The gate driver IC in the example was configured with a tDESATleb,s = 650 ns but similar behavior would be observed for the tDESATleb,l = 1150 ns setting. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 9 v1.0 2020-05-27

This evaluation board was designed with an unpopulated footprint for a DESAT capacitor. In case the vast settings built into the gate driver IC are not covering intended application, a capacitor can be added to adjust the DESAT parameters even further.

1.5.2 So ft-o ff current setting

As mentioned earlier, in the event a fault is detected the gate driver IC will initiate a soft-off current turn-off of the power switch in order to avoid over voltage of the power transistor due to the overcurrent. These fault, generally are either detected by the gate driver IC, via the DESAT protection, or externally by the microcontroller and signaled by pulling RDYC pin low. As shown earlier the gate driver IC can be adjusted to 16 discrete values of the off current. Figure 4 So ft-o ff current with a load of RGOFF = 10 Ω and Cload = 22 nF Figure 4 shows the measurement of the ICSOFF for 15 different setups. The output of the gate driver was connected to a capacitive load Cload = 22 nF via a resistor RGOFF = 10 Ω. These different soft-off turn-off currents can allow for a controlled discharge of the power transistor gate, thus limiting the overcurrent induced voltage overshoot. The gate driver IC has a built in timeout function for the soft-off current. If the OUT voltage does not reach VVEE2 + 2 V in a present amount of time, the gate driver uses all available means to switch-off the output. This includes changing soft-off into hard switch-off and activating the CLAMPDRV output. This timing is defined in the product datasheet and can be clearly observed in the measurement marked with Setup 1. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 10 v1.0 2020-05-27

Figure 5 So ft-o ff current with a load of RGOFF = 10 Ω and Cload = 47 nF Figure 5 shows similar measurements of OUT and DESAT pins with a load RGOFF = 10 Ω and Cload = 47 nF. Setups 0 to 2 are not shows as the switch-off timeout was already reached in setup 3, limiting the turn-off time to the timeout value. Figure 6 Maintaining the same turn-o ff time for two switches with differ ent input capacitances Figure 6 compares the soft turn-off of two different capacitive loads, Cload1 = 22 nF and Cload2 = 47 nF, associated with two different power transistors gate capacitances. The soft turn-off is performed using the same gate resistor. By selecting different resistors at ADJA for the soft-off function, the threshold voltage of both switches can be reached in the same time. This allows to maintain similar behavior of the circuit, despite deploying different power switches. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 11 v1.0 2020-05-27

1.6 Connectors and pin assignment

The following table describes connectors and their pin assignments on the PCB. Table 5 Connectors and pin assignment Connector Pin Marking/function Note X1 1 VCC VCC1 power supply for both gate driver ICs primary side X1 2, 5, 8 SGND Signal ground for primary side, connected to GND1 of both driver ICs X1 3 IN-HS Logic PWM input high side gate driver, referenced to SGND X1 4 IN-LS Logic PWM input low side gate driver, referenced to SGND X1 6 FL T# Fault output, low active and soft- off input, low active, reference to SGND X1 7 RDYC Combined ready output, high active and fault clear input and soft-off input, low active, reference to SGND X40 1 SGND Signal ground for primary side, connected to GND1 of both driver ICs X40 2 P15VP +15 V input supply voltage built in power supply for primary and isolated power supply for secondary side X70 1 VCC2H High side positive gate driver supply X70 2 PHASE/GNDH High side gate driver supply reference X70 3 VEE2H High side negative gate driver supply X80 1 VCC2L Low side positive gate driver supply X80 2 GNDL Low side gate driver supply reference X80 3 VEE2L Low side negative gate driver supply X90 1 P1000VP Half-bridge high voltage positive input X90 2 PHASE Half-bridge mid-point, output connected to GNDH X90 3 GND Half-bridge high voltage negative input, connected to GNDL J40 1, 2 5V EN Jumper to enable 5 V primary operation J70 1, 2 ISO DIS Jumper to disable isolated power supply

1.7 Adjusting the negative gate voltage value for CoolSiC ™ SiC MOSFETs

By default, the board’s bipolar power supply is designed to output +15 V/-7.5 V. These voltages are suitable for driving IGBTs but might not be suitable for driving CoolSiC™ SiC MOSFETs. In order to support evaluation of the gate drivers with CoolSiC™ SiC MOSFETs, the evaluation board was designed with a transistor-zener diode regulator circuit which was left unpopulated. The schematic for the high side negative supply is shown in Figure 7. During the evaluation, the various negative gate voltage requirements of CoolSiC™ SiC MOSFETs have to be considered when selecting the components to populate this circuit. AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 12 v1.0 2020-05-27

Figure 7 High side supply for CoolSiC ™ SiC MOSFET adaption Resistors R70, R80 must be removed and diodes D73, D83, resistors R71, R81, and transistors T70, T80 should be populated in order to adjust the voltage on the VEE2L or VEE2H to the desired voltage. The value of the negative voltage VEE2L/VEE2H rail is given by the breakdown voltage of the Zener diode D73/ D83 plus the VBE voltage drop of the transistor, T70/T80. The current biasing resistors R71/R81 should be selected as such to ensure enough current is drawn from the transistor’s base, while at the same time ensuring that the Zener diodes are not overloaded. The table below shows a bill of materials required to enable -3 V VEE2 operation required for CoolSiC™ SiC MOSFETs switching. Table 6 Component change to enable -3 V VEE2 for CoolSiC™ SiC MOSFETs Designator Manufacturer Manufacturer part number Value D73, D83 Vishay BZX384B3V6-E3-08 3.6 V R71, R81 Vishay CRCW0603560RFK 560 Ω T70, T80 Diodes inc. BC857A - R70, R80 Remove Remove Remove

2 Schematics

The schematics of the evaluation board are separated into the following parts:

Gate driver ICs with surrounding circuit
Power supply for primary and secondary sides
Status interface LEDs
Interfaces with connectors AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description

Application Note 13 v1.0 2020-05-27

FLT#L RDYCL ADJBL ADJAL C50 100nF C54DNP C51 4.7uF R50 22RR51 10R VCC2L C60 100nF C64DNP D64 STTH112A

1 T62

1 T52

FLT#H RDYCH ADJBH ADJAH R52 DNP R62 DNP D54 STTH112A R54 SGND SGND VCC12 VEE2 9 ADJA3 ADJB4 RDYC5 FLT_N6 IN7 GND18 GND11 CLAMPDRV 10 OFF 11ON 12 DESAT 13 VEE2 16 GND2 15 VCC2 14 U10 1ED3491Mx12M VCC12 VEE2 9 ADJA3 ADJB4 RDYC5 FLT_N6 IN7 GND18 GND11 CLAMPDRV 10 OFF 11ON 12 DESAT 13 VEE2 16 GND2 15 VCC2 14 U20 1ED3491Mx12M GNDL C23 1uF C52 4.7uF C61 4.7uF C62 4.7uF X90 1731035 R23 13.7k R24 1.91k R25 2.2k R26 2.2k IN_HS IN_LS FLT# RDYC C10 DNP C11 DNP C12 DNP C20DNPC21DNPC22DNP SGND R10 DNP R11 DNP R12 DNP R20 DNP R21 DNP R22 DNP R13 13.7k VCC R14 1.91k R13 = 13.7KOhm, T_DESATleb = 1.15µs, T_DESATfilter = 2.375µs R14 = 1.91KOhm, I_CSOFF = 131 mA R23 = 13.7KOhm, T_DESATleb = 1.15µs, T_DESATfilter = 2.375µs R24 = 1.91KOhm, I_CSOFF = 131 mA D50DNP D51 DNP D60DNP D61 DNP C90 250nF D52 BAS3010B-03W D62 BAS3010B-03W INH NT_R10 NT_R11 NT_R12 NT_R20 NT_R21 NT_R22 VCC GATE DRIVERS High Voltage Connector PIC1001 PIC1002 COC10 PIC1101 PIC1102 COC11 PIC1201 PIC1202 COC12 PIC1301 PIC1302 COC13 PIC2001 PIC2002 COC20 PIC2101 PIC2102 COC21 PIC2201 PIC2202 COC22 PIC2301 PIC2302 COC23 PIC5001 PIC5002 COC50 PIC5101 PIC5102 COC51 PIC5201 PIC5202 COC52 PIC5301 PIC5302 COC53 PIC5401 PIC5402 COC54 PIC6001 PIC6002 COC60 PIC6101 PIC6102 COC61 PIC6201 PIC6202 COC62 PIC6301 PIC6302 COC63 PIC6401 PIC6402 COC64 PIC9001 PIC9002 COC90 PID5001 PID5002 COD50 PID5101 PID5102 COD51 PID5201 PID5202 COD52 PID5401 PID5402 COD54 PID6001 PID6002 COD60 PID6101 PID6102 COD61 PID6201 PID6202 COD62 PID6401 PID6402 COD64 PINT0R1001 PINT0R1002 CONT0R10 PINT0R1101 PINT0R1102 CONT0R11 PINT0R1201 PINT0R1202 CONT0R12 PINT0R2001 PINT0R2002 CONT0R20 PINT0R2101 PINT0R2102 CONT0R21 PINT0R2201 PINT0R2202 CONT0R22 PIR1001 PIR1002 COR10 PIR1101 PIR1102 COR11 PIR1201 PIR1202 COR12 PIR1301 PIR1302 COR13 PIR1401 PIR1402 COR14 PIR2001 PIR2002 COR20 PIR2101 PIR2102 COR21 PIR2201 PIR2202 COR22 PIR2301 PIR2302 COR23 PIR2401 PIR2402 COR24 PIR2501 PIR2502 COR25 PIR2601 PIR2602 COR26 PIR5001 PIR5002 COR50 PIR5101 PIR5102 COR51 PIR5201 PIR5202 COR52 PIR5401 PIR5402 COR54 PIR6001 PIR6002 COR60 PIR6101 PIR6102 COR61 PIR6201 PIR6202 COR62 PIR6401 PIR6402 COR64 PIT5001 PIT5002 PIT5003 COT50 PIT5201 PIT5202 PIT5203 COT52 PIT6001 PIT6002 PIT6003 COT60 PIT6201 PIT6202 PIT6203 COT62 PIU1001 PIU1002 PIU1003 PIU1004 PIU1005 PIU1006 PIU1007 PIU1008 PIU1009 PIU10010 PIU10011 PIU10012 PIU10013 PIU10014 PIU10015 PIU10016 COU10 PIU2001 PIU2002 PIU2003 PIU2004 PIU2005 PIU2006 PIU2007 PIU2008 PIU2009 PIU20010 PIU20011 PIU20012 PIU20013 PIU20014 PIU20015 PIU20016 COU20 PIX9001 PIX9002 PIX9003 COX90 PIR1401 PIU1003 PIR2401 PIU2003 PIR1301 PIU1004 PIR2301 PIU2004 PIR5201 PIT5201 PIU10010 PIR6201 PIT6201 PIU20010 PIC5402 PIR5401 PIU10013 PIC6402 PIR6401 PIU20013 PINT0R1101 PINT0R2101 PIR1101 PIR2101 PIR2602 PIC1102 PINT0R1102 PIR1102 PIU1006 PIC2102 PINT0R2102 PIR2102 PIU2006 PID5002 PID5102 PID5202 PIR5002 PIR5102 PIR5202 PIT5001 PIT5203 PID6002 PID6102 PID6202 PIR6002 PIR6102 PIR6202 PIT6001 PIT6203 PIC6101 PIC6202 PIC6302 PIC6401 PIC9002 PID6001 PIT6003 PIU20015 PIX9003 PINT0R1001 PIR1001 PINT0R2001 PIR2001 PIC1002 PINT0R1002 PIR1002 PIU1007 PIC2002 PINT0R2002 PIR2002 PIU2007 PID5402 PIR5402 PID6402 PIR6402 PIR5101 PIU10011 PIR6101 PIU20011 PIR5001 PIU10012 PIR6001 PIU20012 PIC9001 PID5401 PIT5002 PIX9001 PIC5101 PIC5202 PIC5302 PIC5401 PID5001 PID6401 PIT5003 PIT6002 PIU10015 PIX9002 PINT0R1201 PINT0R2201 PIR1201 PIR2201 PIR2502 PIC1202 PINT0R1202 PIR1202 PIU1005 PIC2202 PINT0R2202 PIR2202 PIU2005 PIC1001 PIC1101 PIC1201 PIC1301 PIC2001 PIC2101 PIC2201 PIC2301 PIR1302 PIR1402 PIR2302 PIR2402 PIU1001 PIU1008 PIU2001 PIU2008 PIC1302 PIC2302 PIR2501 PIR2601 PIU1002 PIU2002 PIC5002 PIC5102 PID5101 PID5201 PIU10014 PIC6002 PIC6102 PID6101 PID6201 PIU20014 PIC5001 PIC5201 PIC5301 PIT5202 PIU1009 PIU10016 PIC6001 PIC6201 PIC6301 PIT6202 PIU2009 PIU20016 Figure 8 Schematic of gate driver ICs and surrounding circuit AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 14 v1.0 2020-05-27

8.2k R41 33k D80 BAT165 D82 BAT165 C34 10uF D81 BAT165 C80 10uF C81 10uF C82 10uF D70 BAT165 D72 BAT165 D71 BAT165 C70 10uF C71 10uF C72 10uF C35 10uF C36 10uF PRI SEC SEC Tr30 750317493 VCC2L VEE2L GNDL VCC2H VEE2H PHASE D41 Green R40 2.2k VCC5 OSC2 CS1 VB 8 HO 7 VS 6 GND3 LO 4 U30 IR2085S R30 68k C31 470pF C30 100pF C33 100nF C32 100nF R32 15R R33 15R R35 0.47R R34 2.2k 1 2 D30 BAT165 5 6T30A SI3932DV-T1-GE3 2 4T30B SI3932DV-T1-GE3 DC_SW DC_GL DC_GH DC_CS DC_OSC SGND Jumper connected 5V Jumper open 3V3 P15VP P15VP P15VP_ok Supply conector +13V ... +20V J40 fsw = 100kHz J70 R31 33k R80 R70 Jumper connected power supply disabled Jumper open power supply enabled X80 X70 T80 DNP R81 DNP T70 DNP R71 DNP C40 100uF D40 BAS3010B-03W D83 DNP12 D73 DNP Isolated power supply with transformer 5V primary voltage regulator PIC3001 PIC3002 COC30 PIC3101 PIC3102 COC31 PIC3201 PIC3202 COC32 PIC3301 PIC3302 COC33 PIC3401 PIC3402 COC34 PIC3501 PIC3502 COC35 PIC3601 PIC3602 COC36 PIC4001 PIC4002 COC40 PIC4101 PIC4102 COC41 PIC4201 PIC4202 COC42 PIC4301 PIC4302 COC43 PIC4401 PIC4402 COC44 PIC7001 PIC7002 COC70 PIC7101 PIC7102 COC71 PIC7201 PIC7202 COC72 PIC8001 PIC8002 COC80 PIC8101 PIC8102 COC81 PIC8201 PIC8202 COC82 PID3001 PID3002 COD30 PID4001 PID4002 COD40 PID4101 PID4102 COD41 PID7001 PID7002 COD70 PID7101 PID7102 COD71 PID7201 PID7202 COD72 PID7301 PID7302 COD73 PID8001 PID8002 COD80 PID8101 PID8102 COD81 PID8201 PID8202 COD82 PID8301 PID8302 COD83 PIG4001 PIG4002 PIG4003 PIG4004 PIG4005 PIG4006 PIG4007 PIG4008 PIG4009 COG40 PIJ4001 PIJ4002 COJ40 PIJ7001 PIJ7002 COJ70 PIR3001 PIR3002 COR30 PIR3101 PIR3102 COR31 PIR3201 PIR3202 COR32 PIR3301 PIR3302 COR33 PIR3401 PIR3402 COR34 PIR3501 PIR3502 COR35 PIR4001 PIR4002 COR40 PIR4101 PIR4102 COR41 PIR4201 PIR4202 COR42 PIR4301 PIR4302 COR43 PIR7001 PIR7002 COR70 PIR7101 PIR7102 COR71 PIR8001 PIR8002 COR80 PIR8101 PIR8102 COR81 PIT3001 PIT3005 PIT3006 COT30A PIT3002 PIT3003 PIT3004 COT30B PIT7001 PIT7002 PIT7003 COT70 PIT8001 PIT8002 PIT8003 COT80 PITr3002 PITr3005 PITr3007 PITr3008 PITr3009 PITr30010 COTr30 PIU3001 PIU3002 PIU3003 PIU3004 PIU3005 PIU3006 PIU3007 PIU3008 COU30 PIX4001 PIX4002 COX40 PIX7001 PIX7002 PIX7003 COX70 PIX8001 PIX8002 PIX8003 COX80 PIC3102 PIJ7001 PIR3401 PIU3001 PIR3201 PIU3007 PIR3301 PIU3004 PIC3002 PIR3001 PIU3002 PIC3301 PIT3004 PIT3005 PITr3005 PIU3006 PIC8101 PIC8202 PID8202 PID8301 PITr3008 PIX8002 PIR3402 PIR3501 PIT3002 PIR3302 PIT3003 PIR3202 PIT3001 PIJ7002 PIR3101 PIJ4002 PIR4202 PIR4301 PIG4007 PIG4003 PIG4002 PIR4102 PIR4201 PID8302 PIR8102 PIT8001 PID7302 PIR7102 PIT7001 PID4102 PIR4002 PID4002 PIX4002 PIC8201 PID8002 PIR8001 PIR8101 PIT8002 PIC8002 PID8001 PITr3007 PIC8001 PID8102 PID8201 PIC7201 PID7002 PIR7001 PIR7101 PIT7002 PIC7002 PID7001 PITr3009 PIC7001 PID7102 PID7201 PIC4302 PIG4004 PIC3501 PIC3602 PITr3002 PIC3302 PID3001 PIU3008 PIC3202 PIC3402 PIC3502 PIC4001 PIC4102 PIC4202 PID3002 PID4001 PIG4005 PIG4008 PIR3002 PIR3102 PIR4001 PIT3006 PIU3005 PIC7101 PIC7202 PID7202 PID7301 PITr30010 PIX7002 PIC3001 PIC3101 PIC3201 PIC3401 PIC3601 PIC4002 PIC4101 PIC4201 PIC4301 PIC4401 PID4101 PIG4006 PIG4009 PIJ4001 PIR3502 PIR4302 PIU3003 PIX4001 PIC4402 PIG4001 PIR4101 PIC7102 PID7101 PIX7001 PIC8102 PID8101 PIX8001 PIR7002 PIT7003 PIX7003 PIR8002 PIT8003 PIX8003 Figure 9 Schematic of power supply and voltage regulators AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 15 v1.0 2020-05-27

FLT# D44 Green D43 Red R45 330R D42 Green VCC1_ok FLT#_ok D45 Red RDYC_ok R48 2.2k R47 2.2k 1 6 T40A BSD235C T40B BSD235C 1 6 T41A BSD235C T41B BSD235C Status LEDs SGND VCC PID4201 PID4202 COD42 PID4301 PID4302 COD43 PID4401 PID4402 COD44 PID4501 PID4502 COD45 PID4601 PID4602 COD46 PIR4401 PIR4402 COR44 PIR4501 PIR4502 COR45 PIR4601 PIR4602 COR46 PIR4701 PIR4702 COR47 PIR4801 PIR4802 COR48 PIT4001 PIT4002 PIT4006 COT40A PIT4003 PIT4004 PIT4005 COT40B PIT4101 PIT4102 PIT4106 COT41A PIT4103 PIT4104 PIT4105 COT41B PIR4802 PIR4801 PIT4002 PIT4005 PIR4701 PIT4102 PIT4105 PID4602 PIR4402 PID4502 PIR4602 PIT4106 PID4401 PIR4601 PIT4103 PID4302 PIR4502 PIT4006 PID4201 PIR4501 PIT4003 PIR4702 PID4301 PID4501 PID4601 PIT4001 PIT4101 PID4202 PID4402 PIR4401 PIT4004 PIT4104 Figure 10 Schematic of status LEDs IN_HS IN_LS FLT# RDYC SGND VCC SGND SGND ADJBL ADJAL ADJBH ADJAH DESATH ONH OFFH CLAMPH DESATL ONL OFFL CLAMPL INL FLT#L RDYCL INH FLT#H RDYCH SGND SGND 3V3 IH R AB AA SGND SGND 3V3 IL R AB AA SGND SGND Des On Off C Des On Off C VCC VCC Input Connector Test points PITP1001 COTP10 PITP1101 COTP11 PITP1201 COTP12 PITP1301 COTP13 PITP1401 COTP14 PITP1501 COTP15 PITP1601 COTP16 PITP1701 COTP17 PITP2001 COTP20 PITP2101 COTP21 PITP2201 COTP22 PITP2301 COTP23 PITP2401 COTP24 PITP2501 COTP25 PITP2601 COTP26 PITP2701 COTP27 PITP5001 COTP50 PITP5101 COTP51 PITP5201 COTP52 PITP5301 COTP53 PITP6001 COTP60 PITP6101 COTP61 PITP6201 COTP62 PITP6301 COTP63 PIX101 PIX102 PIX103 PIX104 PIX105 PIX106 PIX107 PIX108 COX1 PITP1501 PITP2501 PITP1401 PITP2401 PITP5301 PITP6301 PITP5001 PITP6001 PIX106 PITP1201 PITP2201 PIX103 PIX104 PITP1101 PITP2101 PITP5201 PITP6201 PITP5101 PITP6101 PIX107 PITP1301 PITP2301 PITP1601 PITP1701 PITP2601 PITP2701 PIX102 PIX105 PIX108 PITP1001 PITP2001 PIX101 Figure 11 Schematic of input connectors and test points

3 PCB layout

The layout from this basic schematic is intended as a starting point for developing more complex application circuits. The evaluation board has a four-layer PCB. For orientation, only the assembly diagram and the top and bottom layer are shown. PAC1001 PAC1002 COC10 PAC1101 PAC1102 COC11 PAC1201 PAC1202 COC12 PAC1301 PAC1302 COC13 PAC2001 PAC2002 COC20 PAC2101 PAC2102 COC21 PAC2201 PAC2202 COC22 PAC2301 PAC2302 COC23 PAC3001 PAC3002 COC30 PAC3101 PAC3102 COC31 PAC3201 PAC3202 COC32 PAC3301 PAC3302 COC33 PAC3401 PAC3402 COC34 PAC3502 PAC3501 COC35 PAC3602 PAC3601 COC36 PAC4001 PAC4002 COC40 PAC4101 PAC4102 COC41 PAC4201 PAC4202 COC42 PAC4301 PAC4302 COC43 PAC4401 PAC4402 COC44 PAC5001 PAC5002 COC50 PAC5102 PAC5101 COC51 PAC5202 PAC5201 COC52 PAC5301 PAC5302 COC53 PAC5401 PAC5402 COC54 PAC6001 PAC6002 COC60 PAC6102 PAC6101 COC61 PAC6202 PAC6201 COC62 PAC6301 PAC6302 COC63 PAC6401 PAC6402 COC64 PAC7002 PAC7001 COC70 PAC7102 PAC7101 COC71 PAC7202 PAC7201 COC72 PAC8002 PAC8001 COC80 PAC8102 PAC8101 COC81 PAC8202 PAC8201 COC82 PAC9002 PAC9001 COC90 PAD3002 PAD3001 COD30 PAD4001 PAD4002 COD40 PAD4101 PAD4102 COD41 PAD4201 PAD4202 COD42 PAD4301 PAD4302 COD43 PAD4401 PAD4402 COD44 PAD4501 PAD4502 COD45 PAD4601 PAD4602 COD46 PAD5001 PAD5002 COD50 PAD5101 PAD5102 COD51 PAD5202 PAD5201 COD52 PAD5402 PAD5401 COD54 PAD6001 PAD6002 COD60 PAD6101 PAD6102 COD61 PAD6202 PAD6201 COD62 PAD6402 PAD6401 COD64 PAD7002 PAD7001 COD70 PAD7102 PAD7101 COD71 PAD7202 PAD7201 COD72 PAD7301 PAD7302 COD73 PAD8002 PAD8001 COD80 PAD8102 PAD8101 COD81 PAD8202 PAD8201 COD82 PAD8301 PAD8302 COD83 PAE10MSC01 COE10MSC PAE20MSC01 COE20MSC PAE30MSC01 COE30MSC PAE40MSC01 COE40MSC PAG4001 PAG4002 PAG4003 PAG4004 PAG4005 PAG4006 PAG4007 PAG4008 PAG4009 COG40 PAJ4001 PAJ4002 COJ40 PAJ7002 PAJ7001 COJ70 PAMP10 COMP1 PAMP20 COMP2 PAMP30 COMP3 PAMP40 COMP4 PAR1002 PAR1001 COR10 PAR1102 PAR1101 COR11 PAR1202 PAR1201 COR12 PAR1301 PAR1302 COR13 PAR1401 PAR1402 COR14 PAR2002 PAR2001 COR20 PAR2102 PAR2101 COR21 PAR2202 PAR2201 COR22 PAR2301 PAR2302 COR23 PAR2401 PAR2402 COR24 PAR2501 PAR2502 COR25 PAR2601 PAR2602 COR26 PAR3001 PAR3002 COR30 PAR3101 PAR3102 COR31 PAR3201 PAR3202 COR32 PAR3301 PAR3302 COR33 PAR3401 PAR3402 COR34 PAR3501 PAR3502 COR35 PAR4001 PAR4002 COR40 PAR4101 PAR4102 COR41 PAR4201 PAR4202 COR42 PAR4301 PAR4302 COR43 PAR4401 PAR4402 COR44 PAR4501 PAR4502 COR45 PAR4601 PAR4602 COR46 PAR4702 PAR4701 COR47 PAR4802 PAR4801 COR48 PAR5002 PAR5001 COR50 PAR5102 PAR5101 COR51 PAR5201 PAR5202 COR52 PAR5402 PAR5401 COR54 PAR6001 PAR6002 COR60 PAR6101 PAR6102 COR61 PAR6201 PAR6202 COR62 PAR6402 PAR6401 COR64 PAR7001 PAR7002 COR70 PAR7101 PAR7102 COR71 PAR8001 PAR8002 COR80 PAR8101 PAR8102 COR81 PAT3001 PAT3002 PAT3003 PAT3004 PAT3005 PAT3006 COT30 PAT4006 PAT4005 PAT4004 PAT4003 PAT4002 PAT4001 COT40 PAT4106 PAT4105 PAT4104 PAT4103 PAT4102 PAT4101 COT41 PAT5002 PAT5003 PAT5001 COT50 PAT5203 PAT5201 PAT5202 COT52 PAT6002 PAT6003 PAT6001 COT60 PAT6203 PAT6201 PAT6202 COT62 PAT7003 PAT7001 PAT7002 COT70 PAT8003 PAT8001 PAT8002 COT80 PATP1001 COTP10 PATP1101 COTP11 PATP1201 COTP12 PATP1301 COTP13 PATP1401 COTP14 PATP1501 COTP15 PATP1601 COTP16 PATP1701 COTP17 PATP2001 COTP20 PATP2101 COTP21 PATP2201 COTP22 PATP2301 COTP23 PATP2401 COTP24 PATP2501 COTP25 PATP2601 COTP26 PATP2701 COTP27 PATP5001 COTP50 PATP5101 COTP51 PATP5201 COTP52 PATP5301 COTP53 PATP6001 COTP60 PATP6101 COTP61 PATP6201 COTP62 PATP6301 COTP63 PATr3001 PATr3002 PATr3003 PATr3004 PATr3005 PATr3006 PATr3007 PATr3008 PATr30011 PATr30012 COTr30 PAU1009 PAU10010 PAU10011 PAU10012 PAU10013 PAU10014 PAU10015 PAU10016 PAU1008 PAU1007 PAU1006 PAU1005 PAU1004 PAU1003 PAU1002 PAU1001 COU10 PAU20015 PAU20016 PAU2009 PAU20010 PAU20011 PAU20012 PAU20013 PAU20014 PAU2008 PAU2007 PAU2006 PAU2005 PAU2004 PAU2003 PAU2002 PAU2001 COU20 PAU3008 PAU3007 PAU3006 PAU3005 PAU3004 PAU3003 PAU3002 PAU3001 COU30 PAX102 PAX101 PAX103 PAX104 PAX105 PAX106 PAX107 PAX108 COX1 PAX4001 PAX4002 COX40 PAX7003 PAX7001 PAX7002 COX70 PAX8002 PAX8001 PAX8003 COX80 PAX9001 PAX9002 PAX9003 COX90 PAR1401 PATP1501 PAU1003 PAR2401 PATP2501 PAU2003 PAR1301 PATP1401 PAU1004 PAR2301 PATP2401 PAU2004 PAR5201 PAT5201 PATP5301 PAU10010 PAR6201 PAT6201 PATP6301 PAU20010 PAC3102 PAJ7001 PAR3401 PAU3001 PAR3201 PAU3007 PAR3301 PAU3004 PAC3002 PAR3001 PAU3002 PAC3301 PAT3004 PAT3005 PATr3005 PAU3006 PAC5402 PAR5401 PATP5001 PAU10013 PAC6402 PAR6401 PATP6001 PAU20013 PAR1101 PAR2101 PAR2602 PAR4802 PAX106 PAC1102 PAR1102 PATP1201 PAU1006 PAC2102 PAR2102 PATP2201 PAU2006 PAD5002 PAD5101 PAD5202 PAR5002 PAR5102 PAR5202 PAT5001 PAT5203 PAD6002 PAD6101 PAD6202 PAR6002 PAR6102 PAR6202 PAT6001 PAT6203 PAC6101 PAC6202 PAC6302 PAC6401 PAC8101 PAC8202 PAC9001 PAD6001 PAD8202 PAD8301 PAT6003 PATr3008 PAU20015 PAX8002 PAX9003 PAR1001 PAX103 PAR2001 PAX104 PAC1002 PAR1002 PATP1101 PAU1007 PAC2002 PAR2002 PATP2101 PAU2007 PAC3302 PAD3001 PAU3008 PAC3501 PAC3602 PATr3002 PAC4302 PAG4004 PAC7001 PAD7102 PAD7201 PAC7002 PAD7001 PATr30011 PAC7201 PAD7002 PAR7001 PAR7101 PAT7002 PAC8001 PAD8102 PAD8201 PAC8002 PAD8001 PATr3007 PAC8201 PAD8002 PAR8001 PAR8101 PAT8002 PAD4002 PAX4002 PAD4101 PAR4002 PAD4202 PAR4501 PAT4003 PAD4301 PAR4502 PAT4006 PAD4402 PAR4601 PAT4103 PAD4501 PAR4602 PAT4106 PAD4601 PAR4402 PAD5401 PAR5402 PAD6401 PAR6402 PAD7302 PAR7102 PAT7001 PAD8302 PAR8102 PAT8001 PAG4002 PAR4102 PAR4201 PAJ4002 PAR4202 PAR4301 PAJ7002 PAR3101 PAR3202 PAT3001 PAR3302 PAT3003 PAR3402 PAR3501 PAT3002 PAR4701 PAT4102 PAT4105 PAR4801 PAT4002 PAT4005 PAR5101 PATP5201 PAU10011 PAR6101 PATP6201 PAU20011 PAR5001 PATP5101 PAU10012 PAR6001 PATP6101 PAU20012 PAC1302 PAC2302 PAC4402 PAD4201 PAD4401 PAG4001 PAR2501 PAR2601 PAR4101 PAR4401 PAT4004 PAT4104 PATP1001 PATP2001 PAU1002 PAU2002 PAX101 PAC3202 PAC3402 PAC3502 PAC4001 PAC4102 PAC4202 PAD3002 PAD4001 PAG4005 PAG4008 PAR3002 PAR3102 PAR4001 PAT3006 PAU3005 PAC9002 PAD5402 PAT5002 PAX9001 PAC5101 PAC5202 PAC5302 PAC5401 PAC7101 PAC7202 PAD5001 PAD6402 PAD7202 PAD7301 PAT5003 PAT6002 PATr30012 PAU10015 PAX7002 PAX9002 PAR1201 PAR2201 PAR2502 PAR4702 PAX107 PAC1202 PAR1202 PATP1301 PAU1005 PAC2202 PAR2202 PATP2301 PAU2005 PAC1001 PAC1101 PAC1201 PAC1301 PAC2001 PAC2101 PAC2201 PAC2301 PAC3001 PAC3101 PAC3201 PAC3401 PAC3601 PAC4002 PAC4101 PAC4201 PAC4301 PAC4401 PAD4102 PAD4302 PAD4502 PAD4602 PAG4006 PAG4009 PAJ4001 PAR1302 PAR1402 PAR2302 PAR2402 PAR3502 PAR4302 PAT4001 PAT4101 PATP1601 PATP1701 PATP2601 PATP2701 PAU1001 PAU1008 PAU2001 PAU2008 PAU3003 PAX102 PAX105 PAX108 PAX4001 PAC5002 PAC5102 PAC7102 PAD5102 PAD5201 PAD7101 PAU10014 PAX7001 PAC6002 PAC6102 PAC8102 PAD6102 PAD6201 PAD8101 PAU20014 PAX8001 PAC5001 PAC5201 PAC5301 PAR7002 PAT5202 PAT7003 PAU1009 PAU10016 PAX7003 PAC6001 PAC6201 PAC6301 PAR8002 PAT6202 PAT8003 PAU2009 PAU20016 PAX8003 Figure 12 Assembly drawing top side AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 16 v1.0 2020-05-27

PAC3001 PAC3002 COC30 PAC3101 PAC3102 COC31 PAC3201 PAC3202 COC32 PAC3301 PAC3302 COC33 PAC3401 PAC3402 COC34 PAC3502 PAC3501 COC35 PAC3602 PAC3601 COC36 PAC4001 PAC4002 COC40 PAC4101 PAC4102 COC41 PAC4201 PAC4202 COC42 PAC4301 PAC4302 COC43 PAC4401 PAC4402 COC44 PAC5001 PAC5002 COC50 PAC5102 PAC5101 COC51 PAC5202 PAC5201 COC52 PAC5301 PAC5302 COC53 PAC5401 PAC5402 COC54 PAC6001 PAC6002 COC60 PAC6102 PAC6101 COC61 PAC6202 PAC6201 COC62 PAC6301 PAC6302 COC63 PAC6401 PAC6402 COC64 PAC7002 PAC7001 COC70 PAC7102 PAC7101 COC71 PAC7202 PAC7201 COC72 PAC8002 PAC8001 COC80 PAC8102 PAC8101 COC81 PAC8202 PAC8201 COC82 PAC9002 PAC9001 COC90 PAD3002 PAD3001 COD30 PAD4001 PAD4002 COD40 PAD4101 PAD4102 COD41 PAD4201 PAD4202 COD42 PAD4301 PAD4302 COD43 PAD4401 PAD4402 COD44 PAD4501 PAD4502 COD45 PAD4601 PAD4602 COD46 PAD5001 PAD5002 COD50 PAD5101 PAD5102 COD51 PAD5202 PAD5201 COD52 PAD5402 PAD5401 COD54 PAD6001 PAD6002 COD60 PAD6101 PAD6102 COD61 PAD6202 PAD6201 COD62 PAD6402 PAD6401 COD64 PAD7002 PAD7001 COD70 PAD7102 PAD7101 COD71 PAD7202 PAD7201 COD72 PAD7301 PAD7302 COD73 PAD8002 PAD8001 COD80 PAD8102 PAD8101 COD81 PAD8202 PAD8201 COD82 PAD8301 PAD8302 COD83 PAE10MSC01 COE10MSC PAE20MSC01 COE20MSC PAE30MSC01 COE30MSC PAE40MSC01 COE40MSC PAG4001 PAG4002 PAG4003 PAG4004 PAG4005 PAG4006 PAG4007 PAG4008 PAG4009 COG40 PAJ4001 PAJ4002 COJ40 PAJ7002 PAJ7001 COJ70 PAMP10 COMP1 PAMP20 COMP2 PAMP30 COMP3 PAMP40 COMP4 PAR1002 PAR1001 COR10 PAR1102 PAR1101 COR11 PAR1202 PAR1201 COR12 PAR1301 PAR1302 COR13 PAR1401 PAR1402 COR14 PAR2002 PAR2001 COR20 PAR2102 PAR2101 COR21 PAR2202 PAR2201 COR22 PAR2301 PAR2302 COR23 PAR2401 PAR2402 COR24 PAR2501 PAR2502 COR25 PAR2601 PAR2602 COR26 PAR3001 PAR3002 COR30 PAR3101 PAR3102 COR31 PAR3201 PAR3202 COR32 PAR3301 PAR3302 COR33 PAR3401 PAR3402 COR34 PAR3501 PAR3502 COR35 PAR4001 PAR4002 COR40 PAR4101 PAR4102 COR41 PAR4201 PAR4202 COR42 PAR4301 PAR4302 COR43 PAR4401 PAR4402 COR44 PAR4501 PAR4502 COR45 PAR4601 PAR4602 COR46 PAR4702 PAR4701 COR47 PAR4802 PAR4801 COR48 PAR5002 PAR5001 COR50 PAR5102 PAR5101 COR51 PAR5201 PAR5202 COR52 PAR5402 PAR5401 COR54 PAR6001 PAR6002 COR60 PAR6101 PAR6102 COR61 PAR6201 PAR6202 COR62 PAR6402 PAR6401 COR64 PAR7001 PAR7002 COR70 PAR7101 PAR7102 COR71 PAR8001 PAR8002 COR80 PAR8101 PAR8102 COR81 PAT3001 PAT3002 PAT3003 PAT3004 PAT3005 PAT3006 COT30 PAT4006 PAT4005 PAT4004 PAT4003 PAT4002 PAT4001 COT40 PAT4106 PAT4105 PAT4104 PAT4103 PAT4102 PAT4101 COT41 PAT5002 PAT5003 PAT5001 COT50 PAT5203 PAT5201 PAT5202 COT52 PAT6002 PAT6003 PAT6001 COT60 PAT6203 PAT6201 PAT6202 COT62 PAT7003 PAT7001 PAT7002 COT70 PAT8003 PAT8001 PAT8002 COT80 PATP1001 COTP10 PATP1101 COTP11 PATP1201 COTP12 PATP1301 COTP13 PATP1401 COTP14 PATP1501 COTP15 PATP1601 COTP16 PATP1701 COTP17 PATP2001 COTP20 PATP2101 COTP21 PATP2201 COTP22 PATP2301 COTP23 PATP2401 COTP24 PATP2501 COTP25 PATP2601 COTP26 PATP2701 COTP27 PATP5001 COTP50 PATP5101 COTP51 PATP5201 COTP52 PATP5301 COTP53 PATP6001 COTP60 PATP6101 COTP61 PATP6201 COTP62 PATP6301 COTP63 PATr3001 PATr3002 PATr3003 PATr3004 PATr3005 PATr3006 PATr3007 PATr3008 PATr30011 PATr30012 COTr30 PAU1009 PAU10010 PAU10011 PAU10012 PAU10013 PAU10014 PAU10015 PAU10016 PAU1008 PAU1007 PAU1006 PAU1005 PAU1004 PAU1003 PAU1002 PAU1001 COU10 PAU20015 PAU20016 PAU2009 PAU20010 PAU20011 PAU20012 PAU20013 PAU20014 PAU2008 PAU2007 PAU2006 PAU2005 PAU2004 PAU2003 PAU2002 PAU2001 COU20 PAU3008 PAU3007 PAU3006 PAU3005 PAU3004 PAU3003 PAU3002 PAU3001 COU30 PAX102 PAX101 PAX103 PAX104 PAX105 PAX106 PAX107 PAX108 COX1 PAX4001 PAX4002 COX40 PAX7003 PAX7001 PAX7002 COX70 PAX8002 PAX8001 PAX8003 COX80 PAX9001 PAX9002 PAX9003 COX90 PAR1401 PATP1501 PAU1003 PAR2401 PATP2501 PAU2003 PAR1301 PATP1401 PAU1004 PAR2301 PATP2401 PAU2004 PAR5201 PAT5201 PATP5301 PAU10010 PAR6201 PAT6201 PATP6301 PAU20010 PAC3102 PAJ7001 PAR3401 PAU3001 PAR3201 PAU3007 PAR3301 PAU3004 PAC3002 PAR3001 PAU3002 PAC3301 PAT3004 PAT3005 PATr3005 PAU3006 PAC5402 PAR5401 PATP5001 PAU10013 PAC6402 PAR6401 PATP6001 PAU20013 PAR1101 PAR2101 PAR2602 PAR4802 PAX106 PAC1102 PAR1102 PATP1201 PAU1006 PAC2102 PAR2102 PATP2201 PAU2006 PAD5002 PAD5101 PAD5202 PAR5002 PAR5102 PAR5202 PAT5001 PAT5203 PAD6002 PAD6101 PAD6202 PAR6002 PAR6102 PAR6202 PAT6001 PAT6203 PAC6101 PAC6202 PAC6302 PAC6401 PAC8101 PAC8202 PAC9001 PAD6001 PAD8202 PAD8301 PAT6003 PATr3008 PAU20015 PAX8002 PAX9003 PAR1001 PAX103 PAR2001 PAX104 PAC1002 PAR1002 PATP1101 PAU1007 PAC2002 PAR2002 PATP2101 PAU2007 PAC3302 PAD3001 PAU3008 PAC3501 PAC3602 PATr3002 PAC4302 PAG4004 PAC7001 PAD7102 PAD7201 PAC7002 PAD7001 PATr30011 PAC7201 PAD7002 PAR7001 PAR7101 PAT7002 PAC8001 PAD8102 PAD8201 PAC8002 PAD8001 PATr3007 PAC8201 PAD8002 PAR8001 PAR8101 PAT8002 PAD4002 PAX4002 PAD4101 PAR4002 PAD4202 PAR4501 PAT4003 PAD4301 PAR4502 PAT4006 PAD4402 PAR4601 PAT4103 PAD4501 PAR4602 PAT4106 PAD4601 PAR4402 PAD5401 PAR5402 PAD6401 PAR6402 PAD7302 PAR7102 PAT7001 PAD8302 PAR8102 PAT8001 PAG4002 PAR4102 PAR4201 PAJ4002 PAR4202 PAR4301 PAJ7002 PAR3101 PAR3202 PAT3001 PAR3302 PAT3003 PAR3402 PAR3501 PAT3002 PAR4701 PAT4102 PAT4105 PAR4801 PAT4002 PAT4005 PAR5101 PATP5201 PAU10011 PAR6101 PATP6201 PAU20011 PAR5001 PATP5101 PAU10012 PAR6001 PATP6101 PAU20012 PAC1302 PAC2302 PAC4402 PAD4201 PAD4401 PAG4001 PAR2501 PAR2601 PAR4101 PAR4401 PAT4004 PAT4104 PATP1001 PATP2001 PAU1002 PAU2002 PAX101 PAC3202 PAC3402 PAC3502 PAC4001 PAC4102 PAC4202 PAD3002 PAD4001 PAG4005 PAG4008 PAR3002 PAR3102 PAR4001 PAT3006 PAU3005 PAC9002 PAD5402 PAT5002 PAX9001 PAC5101 PAC5202 PAC5302 PAC5401 PAC7101 PAC7202 PAD5001 PAD6402 PAD7202 PAD7301 PAT5003 PAT6002 PATr30012 PAU10015 PAX7002 PAX9002 PAR1201 PAR2201 PAR2502 PAR4702 PAX107 PAC1202 PAR1202 PATP1301 PAU1005 PAC2202 PAR2202 PATP2301 PAU2005 PAC1001 PAC1101 PAC1201 PAC1301 PAC2001 PAC2101 PAC2201 PAC2301 PAC3001 PAC3101 PAC3201 PAC3401 PAC3601 PAC4002 PAC4101 PAC4201 PAC4301 PAC4401 PAD4102 PAD4302 PAD4502 PAD4602 PAG4006 PAG4009 PAJ4001 PAR1302 PAR1402 PAR2302 PAR2402 PAR3502 PAR4302 PAT4001 PAT4101 PATP1601 PATP1701 PATP2601 PATP2701 PAU1001 PAU1008 PAU2001 PAU2008 PAU3003 PAX102 PAX105 PAX108 PAX4001 PAC5002 PAC5102 PAC7102 PAD5102 PAD5201 PAD7101 PAU10014 PAX7001 PAC6002 PAC6102 PAC8102 PAD6102 PAD6201 PAD8101 PAU20014 PAX8001 PAC5001 PAC5201 PAC5301 PAR7002 PAT5202 PAT7003 PAU1009 PAU10016 PAX7003 PAC6001 PAC6201 PAC6301 PAR8002 PAT6202 PAT8003 PAU2009 PAU20016 PAX8003 Figure 13 PCB top layer PAC1001 PAC1002 COC10 PAC1101 PAC1102 COC11 PAC1201 PAC1202 COC12 PAC1301 PAC1302 COC13 PAC2001 PAC2002 COC20 PAC2101 PAC2102 COC21 PAC2201 PAC2202 COC22 PAC2301 PAC2302 COC23 PAC3001 PAC3002 COC30 PAC3101 PAC3102 COC31 PAC3201 PAC3202 COC32 PAC3301 PAC3302 COC33 PAC3401 PAC3402 COC34 PAC3502 PAC3501 COC35 PAC3602 PAC3601 COC36 PAC4001 PAC4002 COC40 PAC4101 PAC4102 COC41 PAC4201 PAC4202 COC42 PAC4301 PAC4302 COC43 PAC4401 PAC4402 COC44 PAC5001 PAC5002 COC50 PAC5102 PAC5101 COC51 PAC5202 PAC5201 COC52 PAC5301 PAC5302 COC53 PAC5401 PAC5402 COC54 PAC6001 PAC6002 COC60 PAC6102 PAC6101 COC61 PAC6202 PAC6201 COC62 PAC6301 PAC6302 COC63 PAC6401 PAC6402 COC64 PAC7002 PAC7001 COC70 PAC7102 PAC7101 COC71 PAC7202 PAC7201 COC72 PAC8002 PAC8001 COC80 PAC8102 PAC8101 COC81 PAC8202 PAC8201 COC82 PAC9002 PAC9001 COC90 PAD3002 PAD3001 COD30 PAD4001 PAD4002 COD40 PAD4101 PAD4102 COD41 PAD4201 PAD4202 COD42 PAD4301 PAD4302 COD43 PAD4401 PAD4402 COD44 PAD4501 PAD4502 COD45 PAD4601 PAD4602 COD46 PAD5001 PAD5002 COD50 PAD5101 PAD5102 COD51 PAD5202 PAD5201 COD52 PAD5402 PAD5401 COD54 PAD6001 PAD6002 COD60 PAD6101 PAD6102 COD61 PAD6202 PAD6201 COD62 PAD6402 PAD6401 COD64 PAD7002 PAD7001 COD70 PAD7102 PAD7101 COD71 PAD7202 PAD7201 COD72 PAD7301 PAD7302 COD73 PAD8002 PAD8001 COD80 PAD8102 PAD8101 COD81 PAD8202 PAD8201 COD82 PAD8301 PAD8302 COD83 PAE10MSC01 COE10MSC PAE20MSC01 COE20MSC PAE30MSC01 COE30MSC PAE40MSC01 COE40MSC PAG4001 PAG4002 PAG4003 PAG4004 PAG4005 PAG4006 PAG4007 PAG4008 PAG4009 COG40 PAJ4001 PAJ4002 COJ40 PAJ7002 PAJ7001 COJ70 PAMP10 COMP1 PAMP20 COMP2 PAMP30 COMP3 PAMP40 COMP4 PAR1002 PAR1001 COR10 PAR1102 PAR1101 COR11 PAR1202 PAR1201 COR12 PAR1301 PAR1302 COR13 PAR1401 PAR1402 COR14 PAR2002 PAR2001 COR20 PAR2102 PAR2101 COR21 PAR2202 PAR2201 COR22 PAR2301 PAR2302 COR23 PAR2401 PAR2402 COR24 PAR2501 PAR2502 COR25 PAR2601 PAR2602 COR26 PAR3001 PAR3002 COR30 PAR3101 PAR3102 COR31 PAR3201 PAR3202 COR32 PAR3301 PAR3302 COR33 PAR3401 PAR3402 COR34 PAR3501 PAR3502 COR35 PAR4001 PAR4002 COR40 PAR4101 PAR4102 COR41 PAR4201 PAR4202 COR42 PAR4301 PAR4302 COR43 PAR4401 PAR4402 COR44 PAR4501 PAR4502 COR45 PAR4601 PAR4602 COR46 PAR4702 PAR4701 COR47 PAR4802 PAR4801 COR48 PAR5002 PAR5001 COR50 PAR5102 PAR5101 COR51 PAR5201 PAR5202 COR52 PAR5402 PAR5401 COR54 PAR6001 PAR6002 COR60 PAR6101 PAR6102 COR61 PAR6201 PAR6202 COR62 PAR6402 PAR6401 COR64 PAR7001 PAR7002 COR70 PAR7101 PAR7102 COR71 PAR8001 PAR8002 COR80 PAR8101 PAR8102 COR81 PAT3001 PAT3002 PAT3003 PAT3004 PAT3005 PAT3006 COT30 PAT4006 PAT4005 PAT4004 PAT4003 PAT4002 PAT4001 COT40 PAT4106 PAT4105 PAT4104 PAT4103 PAT4102 PAT4101 COT41 PAT5002 PAT5003 PAT5001 COT50 PAT5203 PAT5201 PAT5202 COT52 PAT6002 PAT6003 PAT6001 COT60 PAT6203 PAT6201 PAT6202 COT62 PAT7003 PAT7001 PAT7002 COT70 PAT8003 PAT8001 PAT8002 COT80 PATP1001 COTP10 PATP1101 COTP11 PATP1201 COTP12 PATP1301 COTP13 PATP1401 COTP14 PATP1501 COTP15 PATP1601 COTP16 PATP1701 COTP17 PATP2001 COTP20 PATP2101 COTP21 PATP2201 COTP22 PATP2301 COTP23 PATP2401 COTP24 PATP2501 COTP25 PATP2601 COTP26 PATP2701 COTP27 PATP5001 COTP50 PATP5101 COTP51 PATP5201 COTP52 PATP5301 COTP53 PATP6001 COTP60 PATP6101 COTP61 PATP6201 COTP62 PATP6301 COTP63 PATr3001 PATr3002 PATr3003 PATr3004 PATr3005 PATr3006 PATr3007 PATr3008 PATr30011 PATr30012 COTr30 PAU1009 PAU10010 PAU10011 PAU10012 PAU10013 PAU10014 PAU10015 PAU10016 PAU1008 PAU1007 PAU1006 PAU1005 PAU1004 PAU1003 PAU1002 PAU1001 COU10 PAU20015 PAU20016 PAU2009 PAU20010 PAU20011 PAU20012 PAU20013 PAU20014 PAU2008 PAU2007 PAU2006 PAU2005 PAU2004 PAU2003 PAU2002 PAU2001 COU20 PAU3008 PAU3007 PAU3006 PAU3005 PAU3004 PAU3003 PAU3002 PAU3001 COU30 PAX102 PAX101 PAX103 PAX104 PAX105 PAX106 PAX107 PAX108 COX1 PAX4001 PAX4002 COX40 PAX7003 PAX7001 PAX7002 COX70 PAX8002 PAX8001 PAX8003 COX80 PAX9001 PAX9002 PAX9003 COX90 PAR1401 PATP1501 PAU1003 PAR2401 PATP2501 PAU2003 PAR1301 PATP1401 PAU1004 PAR2301 PATP2401 PAU2004 PAR5201 PAT5201 PATP5301 PAU10010 PAR6201 PAT6201 PATP6301 PAU20010 PAC3102 PAJ7001 PAR3401 PAU3001 PAR3201 PAU3007 PAR3301 PAU3004 PAC3002 PAR3001 PAU3002 PAC3301 PAT3004 PAT3005 PATr3005 PAU3006 PAC5402 PAR5401 PATP5001 PAU10013 PAC6402 PAR6401 PATP6001 PAU20013 PAR1101 PAR2101 PAR2602 PAR4802 PAX106 PAC1102 PAR1102 PATP1201 PAU1006 PAC2102 PAR2102 PATP2201 PAU2006 PAD5002 PAD5101 PAD5202 PAR5002 PAR5102 PAR5202 PAT5001 PAT5203 PAD6002 PAD6101 PAD6202 PAR6002 PAR6102 PAR6202 PAT6001 PAT6203 PAC6101 PAC6202 PAC6302 PAC6401 PAC8101 PAC8202 PAC9001 PAD6001 PAD8202 PAD8301 PAT6003 PATr3008 PAU20015 PAX8002 PAX9003 PAR1001 PAX103 PAR2001 PAX104 PAC1002 PAR1002 PATP1101 PAU1007 PAC2002 PAR2002 PATP2101 PAU2007 PAC3302 PAD3001 PAU3008 PAC3501 PAC3602 PATr3002 PAC4302 PAG4004 PAC7001 PAD7102 PAD7201 PAC7002 PAD7001 PATr30011 PAC7201 PAD7002 PAR7001 PAR7101 PAT7002 PAC8001 PAD8102 PAD8201 PAC8002 PAD8001 PATr3007 PAC8201 PAD8002 PAR8001 PAR8101 PAT8002 PAD4002 PAX4002 PAD4101 PAR4002 PAD4202 PAR4501 PAT4003 PAD4301 PAR4502 PAT4006 PAD4402 PAR4601 PAT4103 PAD4501 PAR4602 PAT4106 PAD4601 PAR4402 PAD5401 PAR5402 PAD6401 PAR6402 PAD7302 PAR7102 PAT7001 PAD8302 PAR8102 PAT8001 PAG4002 PAR4102 PAR4201 PAJ4002 PAR4202 PAR4301 PAJ7002 PAR3101 PAR3202 PAT3001 PAR3302 PAT3003 PAR3402 PAR3501 PAT3002 PAR4701 PAT4102 PAT4105 PAR4801 PAT4002 PAT4005 PAR5101 PATP5201 PAU10011 PAR6101 PATP6201 PAU20011 PAR5001 PATP5101 PAU10012 PAR6001 PATP6101 PAU20012 PAC1302 PAC2302 PAC4402 PAD4201 PAD4401 PAG4001 PAR2501 PAR2601 PAR4101 PAR4401 PAT4004 PAT4104 PATP1001 PATP2001 PAU1002 PAU2002 PAX101 PAC3202 PAC3402 PAC3502 PAC4001 PAC4102 PAC4202 PAD3002 PAD4001 PAG4005 PAG4008 PAR3002 PAR3102 PAR4001 PAT3006 PAU3005 PAC9002 PAD5402 PAT5002 PAX9001 PAC5101 PAC5202 PAC5302 PAC5401 PAC7101 PAC7202 PAD5001 PAD6402 PAD7202 PAD7301 PAT5003 PAT6002 PATr30012 PAU10015 PAX7002 PAX9002 PAR1201 PAR2201 PAR2502 PAR4702 PAX107 PAC1202 PAR1202 PATP1301 PAU1005 PAC2202 PAR2202 PATP2301 PAU2005 PAC1001 PAC1101 PAC1201 PAC1301 PAC2001 PAC2101 PAC2201 PAC2301 PAC3001 PAC3101 PAC3201 PAC3401 PAC3601 PAC4002 PAC4101 PAC4201 PAC4301 PAC4401 PAD4102 PAD4302 PAD4502 PAD4602 PAG4006 PAG4009 PAJ4001 PAR1302 PAR1402 PAR2302 PAR2402 PAR3502 PAR4302 PAT4001 PAT4101 PATP1601 PATP1701 PATP2601 PATP2701 PAU1001 PAU1008 PAU2001 PAU2008 PAU3003 PAX102 PAX105 PAX108 PAX4001 PAC5002 PAC5102 PAC7102 PAD5102 PAD5201 PAD7101 PAU10014 PAX7001 PAC6002 PAC6102 PAC8102 PAD6102 PAD6201 PAD8101 PAU20014 PAX8001 PAC5001 PAC5201 PAC5301 PAR7002 PAT5202 PAT7003 PAU1009 PAU10016 PAX7003 PAC6001 PAC6201 PAC6301 PAR8002 PAT6202 PAT8003 PAU2009 PAU20016 PAX8003 Figure 14 PCB bottom layer

4 Bill of material

The BOM lists all components used for the PCB. Designator Quantity Description Manufacturer PartNumber C13, C23 2 CAP , CERM, 1 µF, 10%, 25 V Taiyo Yuden GMK107AB7105KAHT C30 1 CAP , CERM, 100 pF Kemet C0603C101F5GAC C31 1 CAP , CERM, 470 pF Wurth Elektronik 885012006061 C32, C33, C43, C50, C60, C63

6 CAP , CERM, 100 nF, 20%, 100 V,

Wurth Elektronik 885012206120 C34, C35, C36, C41, C44, C70, C71, C72, C80, C81, C82

11 CAP , CERM, 10 µF, 10%, 25 V Wurth Elektronik 885012208069

C40 1 CAP , ELECTROLYTE, 100 µF Wurth Elektronik 865090445008 C42 1 CAP , CERM, 1 µF Wurth Elektronik 885012106022 C51, C52, C61 3 CAP , CERM, 4.7 µF MuRata GRM21BR61H475KE51 C53 1 CAP , CERM, 100 nF Wurth Elektronik 885012206095 AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 17 v1.0 2020-05-27

Designator Quantity Description Manufacturer PartNumber C62 1 CAP , CERM, 4.7 µF Wurth Elektronik 885012107018 C90 1 CAP , CERM, 250 nF, 900 V, 20% CeraLink TDK Corporation B58031I9254M062 D30, D70, D71, D72, D80, D81, D82 7 Diode, Schottky, 40 V, 0.75 A, SOD-323 Infineon BAT165 D40, D52, D62 3 Diode, Schottky, 30 V, 1 A, SOD-323 Infineon BAS3010B-03W D41, D42, D44, D46 4 LED, Green, SMD Wurth Elektronik 150080VS75000 D43, D45 2 LED, Red, SMD Wurth Elektronik 150080RS75000 D54, D64 2 Diode, 1200 V, 1 A, ultrafast ST STTH112A G40 1 Voltage regulator, 500 mA, 5 V, LDO Infineon IFX1763XEJV50 J40, J70 2 SQ Post Header, 2.54mm pitch, 1x2 pin, vertical, TH Wurth Elektronik 61300211121 R13, R23 2 RES, 13.7k, 1%, 0.1 W, 0805 Vishay CRCW080513K7FK R14, R24 2 RES, 1.91k, 1%, 0.1 W, 0805 Vishay CRCW08051K91FK R25, R26, R34, R40, R47, R48 6 RES, 2.2k, 1%, 0.1 W, 0603 Vishay TNPW06032K20BE R30 1 RES, 68k, 1%, 0.1 W, 0603 Vishay CRCW060368K0FK R31, R41 2 RES, 33k, 1%, 0.1 W, 0603 Vishay CRCW060333K0FK R32, R33 2 RES, 15R, 1%, 0.1 W, 0603 Vishay CRCW060315R0FK R35 1 RES, 1R, 1%, 0.1 W, 0805 Yageo RL0805JR-070R47L R42 1 RES, 11k, 1%, 0.1 W, 0603 Vishay CRCW060311K0FK R43 1 RES, 8.2k, 1%, 0.1 W, 0603 Vishay CRCW06038K20FK R44, R45, R46 3 RES, 330R, 1%, 0.1 W, 0603 Vishay CRCW0603330RFK R50, R60 2 RES, 22R, 1%, 0.25 W, 1206 Vishay CRCW120622R0FK R51, R61 2 RES, 10R, 1%, 0.25 W, 1206 Yageo RC1206FR-0710RL R54, R64 2 RES, 1k, 1%, 0.25 W, 1206 Vishay CRCW12061K00FK R70, R80 2 RES, 0R, 0.1 W, 0603 Vishay CRCW06030000Z0 T30 1 MOSFET , Dual N-Channel, 30 V Vishay SI3932DV-T1-GE3 T40, T41 2 MOSFET , Complemenary P/N- Channel, OptiMOS™ Infineon BSD235C T52, T62 2 MOSFET , N-Channel, 30 V, OptiMOS™ Infineon BSS306N Tr30 1 Transformer, 1.07:1, 2% Wurth Elektronik 750317493 U10, U20 2 Gate driver IC, Single-channel, DSO-16 300 mil fine-pitch Infineon 1ED3491MC12M U30 1 Gate driver IC, Half-Bridge, Self- oscillating, 100 V Infineon IR2085S AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 18 v1.0 2020-05-27

Designator Quantity Description Manufacturer PartNumber X1 1 SQ Post Header, 2.54mm pitch, 1x8 pin, vertical, TH Wurth Elektronik 61300811121 X40 1 TERM BLOCK, 2POS, TH Phoenix Contact 1985195 X70, X80 2 SQ Post Header, 2.54mm pitch, 1x3 pin, vertical, TH Wurth Elektronik 61300311121 X90 1 TERM BLOCK, 3POS 5 mm, TH Wurth Elektronik 691216910003 AN2020-05 EVAL-1ED3491Mx12M (1ED-X3 Analog) Evaluation board description Application Note 19 v1.0 2020-05-27

All referenced product or service names and trademarks are the property of their respective owners. Edition 2020-05-27 Published by Infineon Technologies AG

81726 Munich, Germany

© 2020 Infineon Technologies AG All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference IFX-oko1578558370254 IMPORTANT NOTICE The information contained in this application note is given as a hint for the implementation of the product only and shall in no event be regarded as a description or warranty of a certain functionality, condition or quality of the product. Before implementation of the product, the recipient of this application note must verify any function and other technical information given herein in the real application. Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind (including without limitation warranties of non-infringement of intellectual property rights of any third party) with respect to any and all information given in this application note. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer’s technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.

Summary

Single-channel isolated gate driver IC with adjustable DESAT and soft-off v1.0 2020-05-27

Description