RA1133JAS PERKINELMER | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • 363,000 picture elements (pixels) in a 1100 x 330 configuration
  • 24 µm square pixels
  • 2-phase buried channel process
  • On-chip amplifier for low noise and high speed readout
  • Dynamic range greater than 25,000:1
  • On-chip temperature sensor Caution: While the RA1133J imagers have been designed to resist electrostatic discharge (ESD), they can be damaged from such discharges. Always observe proper ESD precautions when handling and storing these sensors. DSP-303.01C- 8/2002W Page 1 The RA1133J is a full frame CCD sensor with reset capabilities designed specifically for use in spectroscopy, biomedical imaging and related scientific imaging applications. The package for the array is designed with an integrated two stage thermoelectric cooler. This enables the device to be run 40° C below ambient temperature, -15° C when compared to room temperature. Its combination of very low noise and low dark current make it ideal for low light, high dynamic range and high resolution applications. The imager is structured with a single output register at one end of the imaging columns. A lateral reset drain is located adjacent to this readout register which enables the dumping of accumulated charge from the array. Two phase clocks are needed to drive the readout register. Three phase clocks are needed to drive imaging cells. The array is available in a 30-pin metal package with an integrated TE cooler as shown in Figure 1. Package dimensions are shown in Figure 8. MPP Operation A major source of dark current in devices such as this originates in surface states at the Si-SiO2 interface. A unigue design and process enables the RA1133J to be run in "multi-pinned phase" or MPP mode of operation. This helps eliminate dark current generation in the interface surface states. By holding the vertical clocks at negative potential during integration and horizontal signal readout, the surface will not be depleted and the surface state will not generate dark current.

Figure 7. Heat Sink Temperature vs. Chip Temperature Figure 6. TEC Current vs. Chip Temperature (Ambient Temperature)

1.3 C/W

0 C/W

Figure 5. Output Structure

Figure 8. Package Dimensions Table 3. Absolute Maximum Ratings Table 4. Typical Device Specifications

  1. Full well/read noise, MPP mode
  2. RLoad = 5.1 kOhms, MPP mode
  3. Measured at 500 kHz a t -15 ° C

Table 3. Table 5. Recommended Operating Conditions Table 6. Pinout Descriptions

www.perkinelmer.com/opto For more information e-mail us at © 2001 PerkinElmer Inc. All rights reserved. PerkinElmer, the PerkinElmer logo and the stylized “P” are trademarks of PerkinElm er, Inc. DSP-303.01C - 8/2002W Reticon is a registered trademark of PerkinElmer, Inc. Full Frame CCD Sensor Page 8 Table 8.Sales Offices North America United States PerkinElmer Optoelectronics 2175 Mission College Blvd. Santa Clara, CA 95054 Toll Free: 800-775-OPTO (6786) Phone: +1-408-565-0830 Fax: +1-408-565-0703 Europe Germany PerkinElmer Optoelectronics GmbH Wenzel-Jaksch-Str. 31 D-65199 Wiesbaden, Germany Phone: +49-611-492-570 Fax: +49-611-492-165 Asia Japan PerkinElmer Optoelectronics NEopt. 18F, Parale Mitsui Building 8 Higashida-Cho, Kawasaki-Ku Kawasaki-Shi, Kanagawa-Ken 210-0005 Japan Phone: +81-44-200-9170 Fax: +81-44-200-9160 www.neopt.co.jp Singapore 47 Ayer Rajah Crescent #06-12 Singapore 139947 Phone: +65-770-4925 Fax: +65-777-1008

Ordering Information

While the information provided in this data sheet is intended to describe the form, fit and function for this product, PerkinElmer reserves the right to make changes without notice. Part Number RA1133JAS-912 Table 7. Ordering Information site at www.perkinelmer.com/opto. subject to change without notice.