R6S-PF1-R/Q

R6S-PF MSYSTEM | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 3

Technical content

MODEL: R6S-PF1 R6S-PF1 SPECIFICATIONS ES-7781-BF Rev.2 Page 1/3 https://www.m-system.co.jp/ Remote I/O R6 Series POWER SUPPLY MODULE (Tension clamp) Functions & Features

• Provides internal power needed for I/O and network modules from power input 5.9 (.23) (3.70) 102 (4.02) mm (inch) MODEL: R6S–PF1–R[1]

ORDERING INFORMATION

• Code number: R6S-PF1-R[1] Specify a code from below for [1]. (e.g. R6S-PF1-R/Q)
• Specify the specification for option code /Q (e.g. /C01) POWER INPUT DC Power R: 24 V DC (Operational voltage range 24 V ±10 %, ripple 10 %p-p max.) [1] OPTIONS blank: none /Q: With options (specify the specification) SPECIFICATIONS OF OPTION: Q COATING (For the detail, refer to M-System's web site.) /C01: Silicone coating /C02: Polyurethane coating GENERAL SPECIFICATIONS Connection Internal bus: Via the Installation Base (model: R6S-BS) RUN contact output, power supply: Tension clamp (Applicable wire size: 0.2 to 2.5 mm2, stripped length 8 mm) Internal power: Via the Installation Base (model: R6S-BS) Housing material: Flame-resistant resin (black) Isolation: RUN contact output to internal bus or internal power or power input to FG Power indicator LED: Green LED turns on when the power is supplied. RUN indicator: Orange LED turns on in normal communication with the host PLC. ■ RUN CONTACT OUTPUT RUN contact: Terminals (2 – 3) turns ON and (4 – 3) OFF in normal communication with the host PLC; Terminals (2 – 3) turns OFF and (4 – 3) ON in abnormal communication. Rated load: 250 V AC @ 0.5 A (cos ø = 1) 30 V DC @ 0.5 A (resistive load) Maximum switching voltage: 250 V AC or 30 V DC Maximum switching power: 250 VA or 150 W Minimum load: 1 V DC @ 1 mA Mechanical life: 2 × 107 cycles (rate 300 cycles/min.) When driving an inductive load, external contact protection and noise quenching recommended. INSTALLATION Power input
• DC: Operational voltage range 24 V DC ±10 % ripple 10 % p-p max. Approx. 1 A with the maximum I/O extension Operating temperature: -10 to +55°C (14 to 131°F) Operating humidity: 30 to 90 %RH (non-condensing) Atmosphere: No corrosive gas or heavy dust Mounting: Installation Base (model: R6S-BS) Weight: 60 g (2.1 oz) PERFORMANCE Insulation resistance: ≥ 100 MΩ with 500 V DC Dielectric strength: 2000 V AC @ 1 minute (RUN contact output to internal bus or internal power or power input to FG) STANDARDS & APPROVALS EU conformity: EMC Directive EMI EN 61000-6-4 EMS EN 61000-6-2 Low Voltage Directive EN 61010-1,EN 61010-2-201 Measurement Category II (RUN contact output) Pollution Degree 2 RUN contact output to internal bus or power supply: Reinforced insulation (300 V) RoHS Directive

MODEL: R6S-PF1 R6S-PF1 SPECIFICATIONS ES-7781-BF Rev.2 Page 2/3 https://www.m-system.co.jp/ CURRENT CONSUMPTION The network module and I/O modules operate with 24V DC power supply via the power supply module. The total current consumption of the network module and I/O modules is required to be not more than 1 A. If the total current consumption exceeds 1 A, change the combination of I/O modules or reduce the number of I/O modules. R6xSV2 20mA R6xSS2 20mA R6xTS2 20mA R6xTS2A 20mA R6xRS2 20mA R6xDS1 55mA R6xYV2 25mA R6xYS2 45mA R6xDA4 10mA R6xDC4A 20mA R6xDC4B 20mA R6NC1 110mA R6NC3 110mA R6ND1 40mA R6NE1 75mA R6NE2 75mA R6NM1 50mA R6NM2 50mA R6NF1 100mA R6NP1 100mA EXTERNAL VIEW (With the cover open) Power LED RUN LED

MODEL: R6S-PF1 R6S-PF1 SPECIFICATIONS ES-7781-BF Rev.2 Page 3/3 https://www.m-system.co.jp/ EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm [inch] 94 (3.70) 5.9 (.23) *Use a minus screwdriver: tip width 3.8 mm max., tip thickness 0.5 to 0.6 mm 102 (4.02) WIRE INSERTION ANGLE : approx.35° TEST PROBE max. 2 (.08) dia. SCREWDRIVER INSERTION ANGLE : approx. 35° 5 6 7 8 1 2 3 4 SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM Note: In order to improve EMC performance, bond the FG terminal to ground. Caution: FG terminal is NOT a protective conductor terminal. POWER LEDRUN LED NC NO COM FG INTERNAL POWER INTERNAL BUS Ry + POWER INPUT RUN CONTACT OUTPUT BUS CONNECTOR Specifications are subject to change without notice.