Q4008LT TECCOR | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 6

Technical content

Features

  • Glass-passivated junctions
  • Electrically-isolated package
  • Internal trigger diac
  • High surge capability — up to 200 A
  • High voltage capability — 200 V to 600 V TO-220 Isolated MT2 MT1 T

http://www.teccor.com E3 - 2 ©2002 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Specific Test Conditions /g91/g68V±] — Dynamic breakback voltage (forward and reverse) /g68VBO — Breakover voltage symmetry CT — Trigger firing capacitance di/dt — Maximum rate-of-change of on-state current dv/dt — Critical rate-of-rise of off-state voltage at rated V DRM gate open dv/dt(c) — Critical rate-of-rise of commutation voltage at rated V DRM and IT(RMS) commutating di/dt = 0.54 rated IT(RMS)/ms; gate unenergized I2t — RMS surge (non-repetitive) on-state current for period of 8.3 ms for fusing IBO — Peak breakover current IDRM — Peak off-state current gate open; V DRM = maximum rated value IGTM — Peak gate trigger current (10 µs Max) IH — Holding current; gate open IT(RMS) — RMS on-state current, conduction angle of 360° ITSM — Peak one-cycle surge tgt — Gate controlled turn-on time VBO — Breakover voltage (forward and reverse) VDRM — Repetitive peak blocking voltage VTM — Peak on-state voltage at maximum rated RMS current General Notes

  • All measurements are made at 60 Hz with resistive load at an ambi- ent temperature of +25 /g176C unless otherwise specified.
  • Operating temperature range (T J) is -40 /g176C to +125 /g176C.
  • Storage temperature range (T S) is -40 /g176C to +125 /g176C.
  • Lead solder temperature is a maximum of +230 /g176C for 10 seconds maximum; /g1791/16" (1.59 mm) from case.
  • The case temperature (T C) is measured as shown on dimensional outline drawings. See “Package Dimensions” section of this catalog. Electrical Specification Notes (1) For either polarity of MT2 with reference to MT1 (2) See Figure E3.1 for I H versus TC. (3) See Figure E3.4 and Figure E3.5 for i T versus vT. (4) See Figure E3.9 for surge ratings with specific durations. IT(RMS) Part No. VDRM IDRM VTM Trigger Diac Specifications (T–MT1) Isolated /g68VBO VBO [/g68V/g177 ]I BO CT (5) TO-220 (1) Volts (1) (10) mAmps (1) (3) Volts (7) Volts (6) Volts (6) Volts µAmps (11) µFarads TC = 25 °C TC = 100 °C TC = 125 °C T C = 25 °C See “Package Dimensions” section for variations. (12) MIN MAX MAX MAX MIN MAX MIN MAX MAX Q2004LT 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4004LT 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6004LT 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q2006LT 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4006LT 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6006LT 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4006LTH 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6006LTH 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q2008LT 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4008LT 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6008LT 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4008LTH 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6008LTH 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 10 A Q2010LT 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4010LT 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6010LT 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4010LTH 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6010LTH 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 15 A Q2015LT 200 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4015LT 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6015LT 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q4015LTH 400 0.05 0.5 2 1.6 3 33 43 5 25 0.1 Q6015LTH 600 0.05 0.5 2 1.6 3 33 43 5 25 0.1 MT1 MT2 T

©2002 Teccor Electronics E3 - 3 http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 (5) See Figure E3.6, Figure E3.7, and Figure E3.8 for current rating at specific operating temperature. (6) See Figure E3.2 and Figur e E3.3 for test circuit. (7) /g68VBO = [+ VBO] - [- VBO] (8) See Figure E3.7 and Figure E3.8 for maximum allowable case temperature at maximum rated current. (9) Trigger firing capacitance = 0.1 µF with 0.1 µs rise time (10) T C = TJ for test conditions in off state (11) Maximum required value to ensure sufficient gate current (12) See package outlines for lead form configurations. When ordering special lead forming, add type number as suffix to part number. Electrical Isolation All Teccor isolated Quadrac packages withstand a minimum high potential test of 2500 V ac rms from leads to mounting tab over the operating temperature range of the device. The following iso- lation table shows standard and optional isolation ratings.* UL Recognized File #E71639 **For 4000 V isolation, use “V” suffix in part number. IH ITSM dv/dt(c) dv/dt tgt I2t IGTM di/dt (1) (2) mAmps (4) (8) Amps (1) (5) (8) Volts/µSec (1) Volts/µSec (6) (9) µSec Amps 2Sec Amps (9) Amps/µSec TC = 100 °C TC = 125 °C MAX 60/50Hz MIN MIN TYP 40 55/46 3 75 50 3 12.5 1.2 50 40 55/46 3 75 50 3 12.5 1.2 50 40 55/46 3 50 50 3 12.5 1.2 50 50 80/65 4 150 100 3 26.5 1.5 70 50 80/65 4 150 100 3 26.5 1.5 70 50 80/65 4 125 85 3 26.5 1.5 70 50 80/65 25 575 450 3 26.5 1.5 70 50 80/65 25 425 350 3 26.5 1.5 70 60 100/83 4 175 120 3 41 1.5 70 60 100/83 4 175 120 3 41 1.5 70 60 100/83 4 150 100 3 41 1.5 70 60 100/83 25 575 450 3 41 1.5 70 60 100/83 25 425 350 3 41 1.5 70 60 120/100 4 200 150 3 60 1.5 70 60 120/100 4 200 150 3 60 1.5 70 60 120/100 4 175 120 3 60 1.5 70 60 120/100 30 925 700 3 60 1.5 70 60 120/100 30 775 600 3 60 1.5 70 70 200/167 4 300 200 3 166 1.5 100 70 200/167 4 300 200 3 166 1.5 100 70 200/167 4 200 150 3 166 1.5 100 70 200/167 30 925 700 3 166 1.5 100 70 200/167 30 775 600 3 166 1.5 100 Thermal Resistance (Steady State) R/g113JC [R/g113JA] °C/W (TYP) TYPE Isolated TO-220 4A 3.6 [50] 6A 3 . 3 8A 2.8 10 A 2.6 15 A 2.1 Electrical Isolation from Leads to Mounting Tab * VA CR M S T Y P E

2500 Standard

4000 Optional **

http://www.teccor.com E3 - 4 ©2002 Teccor Electronics +1 972-580-7777 Thyristor Product Catalog Figure E3.1 Normalized DC Holding Current versus Case Temperature Figure E3.2 Test Circuit Figure E3.3 Test Circuit Waveforms Figure E3.4 On-state Current versus On-state Voltage (Typical) (4 A to 10 A) Figure E3.5 On-state Current versus On-state Voltage (Typical) (15 A) Figure E3.6 Maximum Allowable Ambient Temperature versus On-state Current Case Temperature (TC) – ˚C -40 -15 +25 +65 +105 IH IH(TC = 25 ˚C) 2.0 1.5 1.0 INITIAL ON-STATE CURRENT = 200 mA DC 4 A to 10 A = 400 mA DC 15 A Ratio of +125 120 V 60 Hz RL D.U.T. MT2 MT1VC CT = 0.1 µF T VC ∆V+ -VBO ∆V- +VBO Positive or Negative Instantaneous On-state Current (iT) – Amps Positive or Negative Instantaneous On-state Voltage (vT) – Volts

6 A, 8 A, and 10 A

TC = 25 ˚C Positive or Negative Instantaneous On-state Current (iT) – Amps 15 A TC = 25˚C 1.8 Positive or Negative Instantaneous On-state Voltage (vT) – Volts 120 100 RMS On-state Current [IT(RMS)] – Amps Maximum Allowable Ambient Temperature (TA) – ˚C 4 A

©2002 Teccor Electronics E3 - 5 http://www.teccor.com Thyristor Product Catalog +1 972-580-7777 Figure E3.7 Maximum Allowable Case Temperature versus On-state Current (4 A) Figure E3.8 Maximum Allowable Case Temperature versus On-state Current (6 A to 15 A) Figure E3.9 Peak Surge Current versus Surge Current Duration Figure E3.10 Power Dissipation (Typical) versus On-state Current (4 A) Figure E3.11 Power Dissipation (Typical) versus On-state Current (6 A to 10 A and 15 A) Figure E3.12 Normalized diac V BO versus Junction Temperature RMS On-state Current [IT(RMS)] – Amps Maximum Allowable Case Temperature (TC) – ˚C CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 ˚CASE TEMPERATURE: Measured as shown on Dimensional Drawings 130 120 110 100 600 4 A RMS On-state Current [IT(RMS)] – Amps Maximum Allowable Case Temperature (TC) – ˚C CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360 ˚CASE TEMPERATURE: Measured as shown on Dimensional Drawings 130 120 110 100 6 A

10 A8 A

1 2 3 4 5 6 8 10 20 3040 60 80 100 200 300 600 1000 100 Surge Current Duration – Full Cycles Peak Surge (Non-repetitive) On-state Current (ITSM) – Amps SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: Resistive RMS ON-STATE CURRENT [IT(RMS)]: Maximum Rated Value at Specified Case Temperature NOTES: 1) Gates control may be lost during and immediately following surge current interval. 2) Overload may not be repeated until junction temperature has returned to steady state rated value. 15 A 10 A 8 A 6 A 4 A Average On-state Power Dissipation [PD(AV)] – Watts RMS On-state Current [IT(RMS)] – Amps 4.0 3.0 2.0 1.0 CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ 4 A CURRENT WAVEFORM: Sinusoidal LOAD: Resistive or Inductive CONDUCTION ANGLE: 360˚ 161412108642 RMS On-state Current [IT(RMS)] – Amps Average On-state Power Dissipation [PD(AV)] – Watts 15 A

6 A to 10 A

-40 -20 0 +20 +40 +60 +80 +100 +120 +140 Junction Temperature (TJ) – ˚C Percentage of VBO Change – %