PSW-120

PSW-120 ALTECH | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 2

Technical content

For the latest on Altech Power Supply specifications please visit www.altechcorp.com/power. OUTPUT INPUT PROTECTION ENVIRONMENT SAFETY & EMC OTHERS Cat. No. PSW-12012 PSW-12024 PSW-12048 DC VOLTAGE 12V 24V 48V RATED CURRENT 10A 5A 2.5A CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~ 2.5A RATED POWER 120W 120W 120W RIPPLE & NOISE (max) 120mVp-p 120mVp-p 150mVp-p Ripple & noise are measured at 20MHz of bandwidth by using a 12 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor. VOLTAGE ADJ. RANGE 12 ~ 15V 24 ~ 29V 48 ~ 58V VOLTAGE TOLERANCE ±1.5% ±1.0% ±1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION ±0.5% ±0.5% ±0.5% LOAD REGULATION ±0.5% ±0.5% ±0.5% SETUP , RISE HOLD UP TIME 2000ms, 70ms, 50ms / 400VAC 2000ms, 70ms, 10ms / 230VAC at full load Length of set up time is measured at cold first start. Turning ON/OFF the power supply very quick may lead to increase of the set up time. VOLTAGE RANGE 180 ~ 550VAC 254 ~ 780VDC FREQUENCY RANGE 47 ~ 63Hz EFFICIENCY (Typ.) 89.5% / 400V 91% / 400V 92% / 400V AC CURRENT 0.55A / 400VAC 1.2A / 230VAC INRUSH CURRENT (Typ.) COLD START 50A LEAKAGE CURRENT ≤ 3.5 mA / 530VAC OVERLOAD 105 ~ 130% rated output power Protection type: Constant current limiting, recovers automatically after fault condition is removed OVERVOLTAGE 16 ~ 18V 31 ~ 37V 60 ~ 67V Protection type: Shut down overvoltage, re-power on to recover OVERTEMPERATURE 105˚C ± 5˚C (12V), 110˚C ± 5˚C (24V) (TSW1) detect on heat sink of power switch transistor; 100˚C ± 5˚C (48V) (TSW1) detect on heat sink of power diode Protection type: Shut down overvoltage, re-power automatically after temperature goes down DC OK SIGNAL Relay contact rating (max.): 30V / 1A resistive WORKING TEMP . -25 ~ +70˚C (Refer to output load derating curve) WORKING HUMIDITY 20 ~ 90% RH non-condensing STORAGE TEMP ., HUMIDITY -40 ~ +85˚C, 10 ~ 95% RH TEMP . COEFFICIENT ±0.03% / ˚C (0 ~ 50˚C) VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60 min. each long X,Y, Z axes Mounting clip: Compliance to IEC60068-2-6 SAFETY STANDARDS UL508 approved IEC60950-1 compliant WITHSTAND VOLTAGE I/P-O/P: 3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC O/P-DC OK:0.5KVAC ISOLATION RESISTANCE I/P-O/P , I/P-FG, O/P-FG: 100M Ohms/500VDC (25˚C; 70% RH) EMI CONDUCTION & RADIATION Compliance to EN55011 (CISPR11), EN55022 (CISPR22), EN61204-3 Class B EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204; EN61204-3; EN61000-6-2; (EN50082-2), heavy industry level; criteria A, The power supply is considered a component which will installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. MTBF 268K hrs min. MIL-HDBK-217K (25˚C) DIMENSION 40x125.2x113.5mm (WxHxD) PACKING 0.65Kg; 20pcs / 14Kg / 1.16CUFT All parameters NOT specially mentioned are measured at 230V AC input, rated load and 25˚C of ambient temperature. Features:

• Single and two phase wide input range 180 ~ 550VAC
• Protections: Short Circuit / Overload / Over Voltage / Overtemperature
• Cooling by free air convection
• Built-in constant current limiting circuit
• DIN rail mountable
• UL508 (industrial control equipment) approved
• EN61000-6-2 (EN50082-2) industrial immunity level
• 100% full load burn-in test
• Built-in DC OK relay contact
• 3 year warranty PSW-120 Series Specifications

Altech Corp.

• 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490 -2501 02 03 04 05 06 0 7 0 (VERTICAL) 100 Terminal Pin No. Assignment (TB1) Terminal Pin No. Assignment (TB2) Pin No. Pin No. 1 1,2 2 3 Assignment Assignment FG AC/L1 AC/L2 DC OUTPU T- V DC OUTPUT+V Relay Contact 12V Others DC OK O.V.P. O.T.P.CONTROL FG I/P -V +VRECTIFIERS FILTERSWITCHING POWER FILTER RECTIFIERS FILTER EMI O.L. P. DETECTION CIRCUIT PWM CURRENT LIMIT DC OK DC OK +V ADJ. 0 4 2 1 2 125.2 TB1 TB2 5 . 3 1 1 180 190 200 250 290 310 450360 490400 500 520 550 100 Mechanical Specification Derating Curve Block Diagram Static Characteristics Note: All dimensions are in millimeters, to convert to inches multiply by 0.03937.