PSPSP500 WALL | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSPSP500 Series

500 Watt Single Output

Built-In Active PFC Function AC/DC Switching Power Supply

FEATURES

  • 3 Year Warranty
  • 100% Full Load Burn-In Tested
  • Universal AC Input / Full Range
  • Built-In Remote Sense Function
  • Built-In Remote ON/OFF Control
  • Current Sharing up to 2000W (3+1)
  • Forced Air Cooling by Built-In DC Fan
  • Built-In Active PFC Function, PF > 0.95
  • With Power Good and Fail Signal Output
  • Open Frame Models Available (“P” Suffix)
  • Short Circuit, Overload, Over Voltage, and Over Temperature Protected SPECIFICATIONS: PSPSP500 Series All specifications are based on 25 o C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. INPUT SPECIFICATIONS Input Voltage Range (See Note 6) 90 ~ 264VAC (127 ~ 370VDC) Input Frequency 47 to 63Hz AC Current (typical) 7A @ 115VAC 3.5A @ 230VAC Inrush Current (typical) 20A @ 115VAC 40A @ 230VAC Leakage Current < 1mA @ 240VAC Power Factor (typical) 0.95 @ 230VAC 0.98 @ 100VAC and full load Remote ON/OFF Control RC+/RC-: 0 ~ 0.8V = power on; 4 ~ 10V = power off sink current < 4 ~ 10mA OUTPUT SPECIFICATIONS Output Voltage See Table Output Power See Table Voltage Tolerance (See Note 3) 5V output: 2.0%, 12V - 48V outputs: 1.0% Voltage Adjustment Range See Table Line Regulation 5V output: 0.5%, 12V - 15V outputs: 0.3%, 24V - 48V outputs: 0.2% Load Regulation 5V output: 2.0%, 12V - 48V outputs: 0.5%, Output Current See Table Ripple & Noise (max) (See Note 2) 5V output: 100mVp-p; 12V - 27V outputs: 150mVp-p; 48V output: 200mVp-p Setup, Rise Time 1500ms, 50ms at full load Hold Up Time (typical) 24ms at full load Temperature Coefficient ±0.03%/°C (0 ~ 50°C) PROTECTION Overload Protection 110 ~ 125% rated output power Protection Type: Constant current limiting; recovers automatically after fault condition is removed Over Voltage Protection See Table Protection Type: Shutdown output voltage; re-power on to recover Over Temperature Protection RTH2 ≥ 95°C detect on heatsink of Q1, Q7 power transistor & L3 output choke Protection Type: Shutdown output voltage; recovers automatically after temperature goes down GENERAL SPECIFICATIONS Efficiency (typical) See Table Withstand Voltage 3000VAC (Input to Output), 1500VAC (Input to FG), 500VAC (Output to FG) Isolation Resistance 100MΩ/500DC (Input to Output, Input to FG, and Output to FG) ENVIRONMENTAL SPECIFICATIONS Working Temperature -10°C to +60°C (refer to output load derating curve) Storage Temperature -20°C to +85°C Working Humidity 20 ~ 90% RH non-condensing Storage Humidity 10 ~ 95% RH Vibration 10 ~ 500Hz, 2G 10min./1 cycle, 60min each along X, Y, Z axes. MTBF 130,100 hours min. @ 25°C (MIL-HDBK-217F) PHYSICAL SPECIFICATIONS Weight PSPSP500 Models: 2500 grams; PSPSP500-P: 1300 grams Dimensions PSPSP500 Models: 278(L) x 127(W) x 63.5(H) mm PSPSP500-P Models: 250(L) x 123(W) x 55(H) mm Warranty 3 years SAFETY & EMC Safety Standards UL60950-1, TUV EN60950-1 approved EMI Conduction & Radiation Compliance to EN55022 (CISPR22) Class B Harmonic Current Compliance to EN61000-3-2,-3 EMS Immunity Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, light industry level, criteria A

Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSPSP500 Series Built-In Active PFC Function AC/DC Switching Power Supply OUTPUT VOLTAGE / CURRENT RATING CHART Model Number Input Voltage Output Voltage Voltage Adjust. Range Over Voltage Protection Output Current Rated Output Power Efficiency PSPSP500-5 5 VDC 4.75 ~ 5.5V 5.75 ~ 6.75V 80A 400W 76% PSPSP500-12 12 VDC 10 ~ 13.2V 13.8 ~ 16.2V 41.5A 498W 82% PSPSP500-15 15 VDC 13.5 ~ 18V 18 ~ 21V 33A 495W 82% PSPSP500-27 27 VDC 24 ~ 30V 31 ~ 36.5V 18.5A 499.5W 84% PSPSP500-48 90 ~ 264 VAC (127 ~ 370 VDC) 48 VDC 41 ~ 56V 57.6 ~ 67.2V 10.5A 504W 86% PSPSP500-5P 5 VDC 4.75 ~ 5.5V 5.75 ~ 6.75V 80A 400W 76% PSPSP500-12P 12 VDC 10 ~ 13.2V 13.8 ~ 16.2V 41.5A 498W 82% PSPSP500-15P 15 VDC 13.5 ~ 18V 18 ~ 21V 33A 495W 82% PSPSP500-27P 27 VDC 24 ~ 30V 31 ~ 36.5V 18.5A 499.5W 84% PSPSP500-48P 90 ~ 264 VAC (127 ~ 370 VDC) 48 VDC 41 ~ 56V 57.6 ~ 67.2V 10.5A 504W 86% NOTES 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load, and 25°C ambient temperature. 2. Ripple & noise are measured at 20MHz bandwidth by using a 12" twisted pair-wire terminated with a 0.1uF & 47uF parallel capacitor. 3. Tolerances include set up tolerance, line regulation, and load regulation. 4. The power supply is considered a component, which will be installed into final equipment. The final equipment must be re-confirmed that it still meets EMC directives. 5. When in parallel connection only one unit may operate if the total output load is less than 5% of rated load condition. 6. Derating may be needed under low input voltages. Please check the derating curve for more details. 7. The “P” suffix indicates models that are open frame. BLOCK DIAGRAM fosc: 134KHz

Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSPSP500 Series Built-In Active PFC Function AC/DC Switching Power Supply PSPSP500 MODELS DERATING CURVE OUTPUT DERATING VS INPUT VOLTAGE MECHANICAL DRAWING AC INPUT TERMINAL PIN NO. ASSIGNMENT DC OUTPUT TERMINAL PIN NO. ASSIGNMENT CONTROL PIN NO. ASSIGNMENT Pin No. Assignment Pin No. Assignment Pin No. Assignment Pin No. Assignment

1 AC/L 1,2,3 DC OUTPUT +V 1 P (Current Share) 5 NC

2 AC/N 4,5,6 DC OUTPUT –V 2 -S 6 PF (Power Fail Signal)

3 FG 3 G 7 +S

4 RC- 8 RC+

Unit: mm

Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSPSP500 Series Built-In Active PFC Function AC/DC Switching Power Supply PSPSP500-P MODELS DERATING CURVE OUTPUT DERATING VS INPUT VOLTAGE MECHANICAL DRAWING CONTROL PIN NO. ASSIGNMENT CONTROL PIN NO. ASSIGNMENT CN1 CN2 Pin No. Assignment Pin No. Assignment Pin No. Assignment

1 GND 1 P (Current Share) 5 PF (Power Fail Signal)

4 GND

Unit: mm AC INPUT TERMINAL PIN NO. ASSIGNMENT Pin No. Assignment

1 AC INPUT

2 AC INPUT

PIN NO. ASSIGNMENT Pin No. Assignment 1, 2, 3 DC OUTPUT +V 4, 5, 6 DC OUTPUT -V Fan Power Source: 0.3A max. SVR1: VO ADJ. SVR2: IO ADJ.

Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833 603-778-2300 www.wallindustries.com Fax 603-778-9797 PSPSP500 Series Built-In Active PFC Function AC/DC Switching Power Supply CONTROL TERMINAL INSTRUCTION MANUAL PARALLEL OPERATION