PSM180 WALL | Alldatasheet

Document overview

  • Manufacturer or author: dhoutz
  • PDF pages: 3

Technical content

Wall Industries, Inc. Rev B PSM180 SERIES 120~180 Watts, Medical AC/DC Power Supplies 04/30/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603677862300 • Toll Free: 888659769255 • Fax 603677869797 website: www.wallindustries.com • e6mail: sales@wallindustries.com Page 1 of 3

FEATURES

  • RoHS Compliant
  • High Power Density
  • Power Factor > 0.95 @ 115VAC
  • 3 x 5 Inch Open Frame Footprint
  • 90~264 VAC Input Voltage Range
  • Single Outputs
  • 87% High Efficiency
  • 120 Watts Output Power with Convection Cooling
  • 180 Watts Output Power with 15CFM Forced Air
  • Over Voltage, Over Load, and Short Circuit Protection
  • Low Leakage Current < 100µA at 264VAC
  • Medical Body Floating (BF) Rated, MOOP Type
  • UL6060161 3rd ed., EN6060161 3rd ed., IEC EN6060161 3rd ed., and CSA6C22.2 No.6060161 3rd ed. Medical Approvals

DESCRIPTION

Size: 5.00 x 3.00 x 1.18 inches 127.0 x 76.2 x 30.0 mm Weight: 12.3oz (350g) The PSM180 series of AC/DC medical power supplies provides 120 Watts with convection cooling and 180 Watts with 15CFM forced airflow in a compact 3 x 5 inch open frame footprint. This series consists of single output models ranging from 12VDC to 48VDC with a 90~264VAC input voltage range. These supplies also feature a low leakage current of less than 100μA at 264VAC, power factor > 0.95 at 115VAC, and 87% typical efficiency. These supplies are also protected against short circuit, over voltage, and over ed., and IEC EN6060161 3rd ed. medical approvals. MODEL SELECTION TABLE Output Current Output Power (1) Model Number Input Range Output Voltage Minimum Load Convection 15CFM Forced Air Convection 15CFM Forced Air Ripple & Noise (2) Output Regulation PSM180B61Y120 12 VDC 0A 10.00A 15.00A 120W 180W 240 mVp6p ±3% PSM180B61Y150 15 VDC 0A 8.00A 12.00A 120W 180W 240mVp6p ±3% PSM180B61Y190 19 VDC 0A 6.32A 9.48A 120W 180W 240mV p6p ±2% PSM180B61Y240 24 VDC 0A 5.00A 7.50A 120W 180W 240mVp6p ±2% PSM180B61Y280 28 VDC 0A 4.29A 6.43A 120W 180W 240mV p6p ±2% PSM180B61Y480 90 6 264 VAC 48 VDC 0A 2.50A 3.75A 120W 180W 240mVp6p ±2% NOTES 1. 120W max. with convection cooling and 180W max. with 15CFM minimum forced airflow. 2. Ripple & noise is measured at 20MHz limited bandwidth and with a 10µF electrolytic capacitor and a 0.1µF ceramic capacitor in parallel across the output. DERATING CURVES Derating Curve with Convection Cooling Derating Curve with 15CFM Forced Air 100 120 0 10 20 30 40 50 60 70 80 Output Power (%) Ambient Temperature (°C) 100 120 0 10 20 30 40 50 60 70 80 Output Power (%) Ambient Temperature (°C)

Wall Industries, Inc. Rev B PSM180 SERIES 120~180 Watts, Medical AC/DC Power Supplies 04/30/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603677862300 • Toll Free: 888659769255 • Fax 603677869797 website: www.wallindustries.com • e6mail: sales@wallindustries.com Page 2 of 3 SPECIFICATIONS: PSM180 SERIES All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted. We reserve the right to change specifications based on technological advances. SPECIFICATION TEST CONDITIONS Min Typ Max Unit INPUT SPECIFICATIONS Input Voltage Range 90 264 VAC Input Frequency 47 63 Hz 115VAC and full load 3 Input Current (rms) 230VAC and full load 1.5 A 115VAC, cold start, 25°C 50 Inrush Current 230VAC, cold start, 25°C 100 A 115VAC and full load 0.95 Power Factor Correction 230VAC and full load 0.90 OUTPUT SPECIFICATIONS Output Voltage See Table Output Regulation See Table Convection cooling 120 Output Power 15CFM forced air cooling 180 W Output Current See Table Minimum Load 0 % Ripple & Noise (20MHz BW) Measured at 20MHz limited bandwidth and with a 10µF electrolytic capacitor and a 0.1µF ceramic capacitor in parallel across the output 240 mVp6p Hold6up Time 115VAC and full load 20 ms PROTECTION Over Voltage Protection Latching type, AC recycle Over Load Protection automatic recovery 110 150 % Short Circuit Protection automatic recovery GENERAL SPECIFICATIONS Efficiency 115VAC and full load 87 % ENVIRONMENTAL SPECIFICATIONS Convection cooling Derating linearly 2.5% per °C fr om 41°C to +60°C 0 +60 °C Operating Ambient Temperature 15CFM forced air Derating linearly 2.5% per °C from 51°C to +60°C 0 +60 °C Storage Temperature Range 640 +85 °C Humidity Non6condensing 5 95 % MTBF Full load and 25°C ambient temperature 100,000 hours PHYSICAL SPECIFICATIONS Weight 12.3oz (350g) Input Connector (CN1) Mates with JST VHR63N or equi valent JST B3P6VH6B pitch: 3.96mm or equivalent Output Connector (CN2) Mates with JST VHR66N or equivalent JST B6P6VH6B pitch: 3.96mm or equivalent SAFETY & EMC EMC Standards EN606016162, FCC Part 18 Class B, EN55011 Class B, CE

Wall Industries, Inc. Rev B PSM180 SERIES 120~180 Watts, Medical AC/DC Power Supplies 04/30/2014 Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603677862300 • Toll Free: 888659769255 • Fax 603677869797 website: www.wallindustries.com • e6mail: sales@wallindustries.com Page 3 of 3 MECHANICAL DRAWING 5.00 [127.0] 0.22 [5.7] 0.22 [5.7] 2.55 [64.8] 3.00 [76.2] 4X Ø3.5 Mounting Holes 3.00 [76.2] 0.087 [2.2] CN2 CN1 Unit: inches [mm] CN1: INPUT CONNECTOR Pin No. Signal

1 AC Neutral

2 AC Line

JST B3P-VH-B pitch: 3.96mm or equivalent, mates with JST VHR-3N or equivalent CN2: OUTPUT CONNECTOR Pin No. Signal

1 GND

2 GND

3 GND

JST B3P-VH-B pitch: 3.96mm or equivalent, mates with JST VHR-3N or equivalent COMPANY INFORMATION Wall Industries, Inc. has created custom and modified units for over 50 years. Our in6house research and development engineers will provide a solution that exceeds your performance requirements on6time and on budget. Our ISO900162008 certification is just one example of our commitment to producing a high quality, well6documented product for our customers. Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss your future projects. Contact Wall Industries for further information: Phone: /telephonesolid(603)77862300 Toll Free: /telephonesolid(888)59769255 Fax: /telephonesolid(603)77869797 E6mail: sales@wallindustries.com Web: www.wallindustries.com Address: 37 Industrial Drive Exeter, NH 03833