PPM165-SIP PEAK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 1/3 PPMxx-SIP-xxELF All specifications typical at Ta=25° C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range 100 – 400 VDC or 85 – 264 VAC* universal Input Current 40mA, typ. External Input Fuse (recommended) 0.5A / 250V * Attention: For AC-Input a capacitor between PIN 7 and PIN 10 is needed!! (See page 3) Output Specifications Voltage Accuracy ±2% Input variation ±0.5%, typ. Load variation (10-100%) ±1%, typ. Ripple and Noise (20Mhz bandwidth) 3.3 / 5 / 9 VDC models

12 VDC models

15 VDC models

≤ 100mV pk-pk ≤ 120mV pk-pk ≤ 150mV pk-pk ≤ 240mV pk-pk Short Circuit Protection Continuous, auto recovery Over Temperature Protection 150° C, max. Common Specifications Temperature range -40° C to +85 ° C Power derating 1.33% / ° C (above 55° C) Case temperature +90° C, max. Storage -40° C to +105 ° C Humidity (non condensing) 85%, max. Temperature Coefficient 0.02%/° C Switching Frequency 100kHz, typ. I/O Isolation Voltage 2000VAC / 1min. Leakage current None Case Material UL94V-0 rated Reliability Calculated MTBF (MIL-HDBK-217F) > 300,000 hrs Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de The PPM -S IP -Series are high efficiency green power modules with miniature packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficienc y, high reliability, low loss, safety isolation etc. They are widely used in indus trial, office and civil equipments, as well as applications where no specia l requirement for EMC performance. It is recommended to add EMI suppression circuit or take measure to shield when there is strict requirement for EMC performance. PPM-SIP-SERIES /checkbld 1.65 - 3 Watt /checkbld Univ. 100-400VDC / 85-264VAC* /checkbld Single Output /checkbld Over Temperature Protection /checkbld Short Circuit Protection /checkbld 2 kV AC I/O Isolation /checkbld High Efficiency / Density Rev.08-2011

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 2/3 Selection Guide Order # P o w e r (W ) O u tp u t V o lta g e (V d c ) O u tp u t C u rre n t F u ll L o a d (m A ) E ffic ie n c y (% ) SINGLE OUTPUT PPM1.65-SIP-3R3ELF 1.65 3.3 500 70 PPM2.5-SIP-05ELF 2.5 5 500 70 PPM3-SIP-09ELF 3 9 330 75 PPM3-SIP-12ELF 3 12 250 78 PPM3-SIP-15ELF 3 15 200 78 PPM3-SIP-24ELF 3 24 125 78 If you need other specifications, please enquire. Package / Pinning / Derating max. 25.50 (1.004) 1 12 max. 35.00 (1.38) 5.08 (0.20) 3.53 (0.14) max. > 3.00 (0.12)3 7 10 0.40 (0.016) 10.50 (0.413) max. Printed Face 0.84 (0.033) All dimensions are typical in millimeters (inches). B Pin section tolerance: +/B0.10 (+/B0.004) B Case tolerance +/B0.5 (+/B0.02) Specification may change without notice. SIP – AC/DC Backside 22.86 (0.90) 12.70 (0.50) # SINGLE 1 +Vout 3 - Vout 7 - Vin

10 CAP

Load(%) Temperature( C) -20 55 85 -40

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 3/3 App Notes: Structure Figure DC/DC Convertor +Vin(L) -Vin(N) External Capacitor Rectificate Contrl Circuit Feedback loop Voltage sampling Rectifier filter circuit +Vo -Vo Anear Measure C2 C3 25.4mm 25.4mm Fuse 10 +C1 Copper sheet Load Connect Oscillograph Probe Typical Application DC Input AC Input C2 12 C3 +Vo -Vo TvS RL 1+Vin -Vin Fuse MOV C2 12 C3 +Vo -Vo TvS RL N Fuse + 10 N F C 6 MOV EMC Filter LS03 DC input typical application LS03 AC input typical application External Capacitor Typical Value Output Voltage C1 C2 C3 FUSE TVS 3.3V 5V P4KE6.8A 9V P4KE12A 12V 150 µF/25V 15V P4KE20A 24V 10 µF/400V 100 µF/35V 0.1 µF/50V (Ceramic Capacitor) 0.5A/250V P4KE33A Note: 1. Filtering capacitors C1, C2 are electrolytic cap acitors, C1 is used for AC input, when input voltag e is below 100VAC, the value of C1 is 22µF/400V. C2 is recommended to use high frequency and low impedance electrolytic capac itors. For capacitance and current of capacitor please refer t o manufacture’s datasheet. Voltage derating of capa citor should be 80% or above. C3 is ceramic capacitor. It is used to filte r high frequency noise. TVS is a recommended compon ent to protect post- circuits (if converter fails). 2. MOV: Voltage dependent resistor, model 471KD05. It is used to protect converter in lightning strike and surge. 3. If EMC performance is required, it’s recommended to add “EMC filter” at the input side. C4: X capac itor: 0.1µF/275V C5,C6: Y capacitor: 220pF/2000V NF: Common-mode cho ke, recommended parameter: 10mH-30mH Attention: For AC-Input a capacitor (10uF/400V) between PIN 7 and PIN 10 is needed!!