PPM50-G-05ELF

PPM50-G-05ELF PEAK | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 4

Technical content

PPM-Series – PPM50/60-G-xxELF – Single Output - Pla stic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 1/4 PPM50-G-xxELF PPM60-G-xxELF All specifications typical at Ta=25° C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range 90 – 264 VAC or 122 – 370 VDC universal Input Under Voltage Protection Start-up Voltage: 65 -90 Vac (92-122VDC) Shutdown Voltage: 55- 75 Vac (79-105 VDC) Input Frequency 47 – 63 Hz Input Current 115 VAC at 1.4A, typ 230 VAC at 0.7A, typ Inrush Current 115 VAC at 30A, typ 230 VAC at 50A, typ Output Specifications Voltage Accuracy ±2% Line Regulation (full load) ±0.5%, typ Load Regulation (5-100%) ±1%, typ Ripple and Noise (20Mhz bandwidth) 150mV pk-pk, max Short Circuit Protection Continuous, auto resume Over Current Protection 110-150% , auto resume Over Voltage Protection Zener Diode Clamp Min Load 1% Trim 10% Common Specifications Temperature range -40° C to +70 ° C Power derating 3% / ° C ( output: 05, 09 VDC ) 2.5% / ° C ( output: 12,15,24,48 VDC ) Storage -40° C to +85 ° C Hold up Time 15mS, typ . at 115VAC 80mS, typ at 230VAC Humidity 95%, max. Temperature Coefficient ± 0.02%/° C Switching Frequency 100kHz, typ I/O Isolation Voltage 4000VAC / 1min. Safety Standards IEC60950, EN60950, UL60950 Safety Approvals pending Safety Class CLASS I Hot swap Forbid Case Material UL94V-0 rated Install PCB Cooling Free air convection Reliability Calculated MTBF (MIL-HDBK-217F) > 200,000 hrs Weight ~ 310g Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de The PPM -Series are high efficiency green power moduls with various packaging provided by Peak. The features of this se ries are: wide input voltage, DC and AC all in one, high efficiency, hig h reliability, low loss, safety isolation etc. They are widely used in indus trial, office and civil equipments. PPM-SERIES /checkbld 50-60 Watt /checkbld Univ. 90-264VAC (122-370VDC) /checkbld Single Output /checkbld Over Voltage Protection (out) /checkbld 4 kV AC I/O Isolation /checkbld Low Ripple and Noise /checkbld High Efficiency Rev.03-2013

PPM-Series – PPM50/60-G-xxELF – Single Output - Pla stic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 2/4 Selection Guide Single Output Order # P o w e r (W ) O u tp u t V o lta g e (V d c ) O u tp u t C u rre n t F u ll L o a d (m A ) E ffic ie n c y (%) C a p a c ito r L o a d (u F ) S ta n d b y P o w e r, m a x SINGLE OUTPUT PPM50-G-05ELF 50 5 10000 82 80000 0.5W PPM50-G-09ELF 50 9 6600 84 28000 0.5W PPM50-G-12ELF 50 12 5000 86 14000 0.5W PPM60-G-15ELF 60 15 4000 86 12000 0.5W PPM60-G-24ELF 60 24 2500 86 4000 0.5W PPM60-G-48ELF 60 48 1250 86 1000 0.5W If you need other specifications, please enquire. Package / Pinning / Derating Note: Unit: mm (inch) Pin 1,2 4, 5’s diameter: 1.80mm, Pin 3, 6’s diameter: 1.20mm 30.00 [1.181] 6.00 ： [0.236] 109.00 ： [4.291] 58.50 ： [2.303] 97.30 [3.831] 2- 1.20[0.047] ∅ 4- 1.80[0.071] ∅ 19.05 ： [0.750] 10.16 ： [0.400] 96.32 ： [3.792] 8.90 ： [0.350] 5.08 [0.200] 30.70 [1.209] 15.60 [0.614] 46.30 [1.823] 4- 3[0.118] M (Front View) (Bottom View) # SINGLE

1 AC (N)

2 AC (L)

6 Trim

Temperature Derating Graph Ambient Temperature ° C 100% -40 0 100 45 50 55 Output 62,5 -30 24V, 48V Output 12V, 15V Output 5V, 9V Output

PPM-Series – PPM50/60-G-xxELF – Single Output - Pla stic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 3/4 App Notes: Trim Application & Trim Calculation Application circuit for TRIM (Part in broken line is the interior of models) 0V Vref RT Trim +Vot Vref RT Trim +Vot Trim up Trim down Formula for resistance of Trim φ up: a= Vref Vot-Vref R1R = T aR 2 R -a 2 -R 3 down: a= Vref Vot-Vref R2R = T aR 1 R -a 1 -R 3 Note: Value for R1, R2, R3, and Vref refer to the following table. R T: Resistance of Trim a: User-defined parameter, no actual meanings. Vo(V) Resistance 5 9 12 15 24 48 R2(K Ω) 3.3 1.8 1 1.5 1 1.8 R3(K Ω) 1 1 1 1 1 1 Vot(V) Output voltage of Trim, variation ≤ ±10% EMC EMI EN55022, level B EMS ESD IEC/EN 61000-4-2 ±6kV/8kV perf. Criteria B RS IEC/EN 61000-4-3 10V/m perf. Criteria A EFT IEC/EN 61000-4-4 ±4kV perf. Criteria B Surge IEC/EN 61000-4-5 ±2kV/4kV perf. Criteria B CS IEC/EN 61000-4-6 10 Vr.m.s. perf. Criteria A PFM IEC/EN 61000-4-8 10A/m perf. Criteria A Voltage dips, short and interruption immunity IEC/EN 61000-4-11 95% 5000ms perf. Criteria B Parallel Lines Measure AC-DC +Vo -Vo FUSE L N 2 5 .4 mm 2 5 . 4 mm C1 C2 1 2 .7 mm Copper sheet Connect Oscillograph Probe Load L N Note: C1: 1µF (Ceramic capacitor) C2: 10µF (Electrolytic capacitor)

PPM-Series – PPM50/60-G-xxELF – Single Output - Pla stic Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 4/4 App Notes: Typical Applications PPM-Series Fig 1 L +Vo -Vo L N N C1 C2 TVS RL FUSE FG Fig 2 L N +Vo -Vo AC-DC L N +Vo -Vo FG Note: This application is not supported for this series. N L LCM OU TPUT N L ACDC PE MOV1 MO V2 CX MOV4 MO V5 Cy1 CY2 CY1 External Typical Value Model C1 C2 TVS PPM50-G-05ELF 680µF SMBJ7.0A PPM50-G-09ELF 470 µF SMBJ12A PPM50-G-12ELF 330 µF SMBJ20A PPM60-G-15ELF 330 µF SMBJ30A PPM60-G-24ELF 200µF SMBJ30A PPM60-G-48ELF 1µF 100µF SMBJ64A Note 1. Output filtering capacitors C2 is electrolytic cap acitors. It is recommended to use high frequency an d low impedance electrolytic capacitors. For capacitance and curren t of capacitor, please refer to manufacture’s datas heet. Voltage derating of capacitor should be 80% or above. C1 is ceramic capacitor - it is used to filter high freq uency noise. TVS is a recommended component to protect post-circuits (if converter fails). 2. External connect FUSE, recommended the parameter is 3.15A/250V slow blow. Figure 3 φ MOV1 φ561KD14 χ MOV2 ȽMOV3 φ561KD14 χ MOV4 ȽMOV5 φ561KD07 χ CX φ0.15µF/300VAC χ CY1 ȽCY2 φ2200pF/400VAC χ R1 φ1M Ω/2W χ NTC φ5D-9χ FUSE φRecommended to use3.15A/250V slow blow.