PPM1.65-SIP-3R3ELF PEAK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/3 PPMxx-SIP-xxELF All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range 100 – 300 VDC or 85 – 264 VAC* universal Input Current 40mA, typ. Frequency 47 – 80 Hz External Input Fuse (recommended) 1A / 250V * Attention: For AC-Input a capacitor between PIN 7 and PIN 10 is needed!! (See page 3) Output Specifications Voltage Accuracy ±2% Input variation ±0.5%, typ. Load variation (10-100%) ±1%, typ. Ripple and Noise (20Mhz bandwidth) 3.3 / 5 / 9 VDC models

12 VDC models

15 VDC models

≤ 100mV pk-pk (50mV pk-pk typ.) ≤ 120mV pk-pk (60mV pk-pk typ.) ≤ 150mV pk-pk (75mV pk-pk typ.) ≤ 240mV pk-pk (120mV pk-pk typ.) Short Circuit Protection Continuous, auto recovery Over Temperature Protection 150°C, max. Common Specifications Temperature range -40°C to +85 °C Power derating 1.33% / °C (above 55°C) Case temperature +90°C, max. Storage -40°C to +105 °C Humidity (non condensing) 85%, max. Temperature Coefficient 0.02%/°C Switching Frequency 100kHz, typ. I/O Isolation Voltage 2000VAC / 1min. Leakage current None Case Material UL94V-0 rated Reliability Calculated MTBF (MIL-HDBK-217F) > 300,000 hrs Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de The PPM-SIP-Series are high efficiency green power modules with miniature packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments, as well as applications where no special requirement for EMC performance. It is recommended to add EMI suppression circuit or take measure to shield when there is strict requirement for EMC performance. PPM-SIP-SERIES  1.65 - 3 Watt  Univ. 100-300VDC / 85-264VAC*  Single Output  Over Temperature Protection  Short Circuit Protection  2 kV AC I/O Isolation  High Efficiency / Density Rev.09-2015

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/3 Selection Guide Order # Power (W) Output Voltage (Vdc)Output Current Full Load (mA)Efficiency (%) SINGLE OUTPUT PPM1.65-SIP-3R3ELF 1.65 3.3 500 70 PPM2.5-SIP-05ELF 2.5 5 500 70 PPM3-SIP-09ELF 3 9 330 75 PPM3-SIP-12ELF 3 12 250 78 PPM3-SIP-15ELF 3 15 200 78 PPM3-SIP-24ELF 3 24 125 78 If you need other specifications, please enquire. Package / Pinning / Derating max. 25.50 (1.004) 1 12 max. 35.00 (1.38) 5.08 (0.20) 6.00 (0.236) 3 7 10 0.40 (0.016) 10.50 (0.413) max. Printed Face 0.84 (0.033) All dimensions are typical in millimeters (inches). - Pin section tolerance: +/-0.10 (+/-0.004) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. SIP – AC/DC Backside 22.86 (0.90) 12.70 (0.50) # SINGLE 1 +Vout 3 - Vout 7 - Vin

10 CAP

Load(%) Temperature( C) -20 55 85-40 Ø 1.30 (0.051)

PPM-SIP-Series – PPMxx-SIP-xxELF – Single Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/3 App Notes: Structure Figure DC/DC Convertor +Vin(L) -Vin(N) External Capacitor Rectificate Contrl Circuit Feedback loop Voltage sampling Rectifier filter circuit +Vo -Vo Anear Measure Copper sheet Load Connect Oscillograph Probe FUSE L N Note: C1: 1µF (Ceramic capacitor) C2: 10µF (Electrolytic capacitor) Typical Application C2 C3 +Vo -Vo TVS RL N + 10 + CY FUSE NTC MOV L N +Vo -Vo AC-DC L N +Vo -Vo Fig. 1: Standard Fig. 2: This application is not supported for this Series. OUTPUT N L N L PE LCMMOV R3CX CY3 CY4 ACDC CY1 CY2 + 10 CY LDM can use MORNSUN’s FC-L01D FUSE Fig. 3: PPM-SIP-Series Recommended circuit for application require higher EMC standard (external circuit output same as above) External Capacitor Typical Value Output Voltage C1 C2 C3 FUSE TVS 3.3V 10μF/400V 1μF/50V 150μF/25V 1A/250V SMBJ7.0A 5V 9V SMBJ12A 12V SMBJ20A 15V 100μF/35V 24V SMBJ30A Note: 1. C1: AC input, is a filtering electrolytic capacitor, which is required when input voltage is below 100VAC, and the value of C1 is 22μF/400V. DC input, is a filtering capacitor in EMC Filter, the value of C1 is 10 µF/400V (when input voltage is above 270VDC, and the value of C1 is 10µF/450V), If EMC performance is not required, C1 could not need. 2. C2 is ceramic capacitor, it is used to filter high frequency noise. Output filtering capacitor C3 (which is required by AC input or DC input) is recommended to use high frequency and low imp edance electrolytic capacitors. Voltage derating of capacitor should be 80% or above. TVS is a recommended component to protect post-circuits (if converter fails). 3. Recommended external circuit parameters in Figure 3: MOV: Varistor, model: 561KD14，it is used to protect the device under surge; R1、R2：2Ω/3W Winding resistor；R3：1MΩ/2W； CY、CY1、CY2、CY3、CY4：102M/400VAC；CX：0.22µF/275VAC； LCM：10mH-30mH；LDM：300µH； 4. FUSE：1A/250V Slow-Blow Attention: For AC-Input a capacitor (10uF/400V) between PIN 7 and PIN 10 is needed!!