PMI104-F90-IE8-V15

PMI104-F90-IE8-V15 PF | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 5

Technical content

Inductive positioning system PMI104-F90-IE8-V15 < Analog output 4 mA ... 20 mA < Adjustable switch points < Measuring range 0 ... 104 mm Dimensions Button M5 (2x) 22 23 126 107 LED LED Power S1 S2 S2 S1 M12 x 1 20 mA 4 mA Technical Data General specifications Switching element function Analog current output with PNP binary NO Object distance 0.5 ... 3 mm , recommended: 2 mm Measurement range 0 ... 104 mm Linearity range 1 ... 103 mm Nominal ratings Operating voltage UB 18 ... 30 V DC Reverse polarity protection reverse polarity protected Linearity error within measuring range: ± 0.8 mm within linearity range: ± 0.4 mm Repeat accuracy R ± 0.1 mm Resolution 125 µm Temperature drift ± 0.5 mm (-25 °C ... 70 °C) No-load supply current I0 ≤ 40 mA Operating voltage indicator LED green Release date: 2020-03--

23 Date of

Release date: 2020-03-23 Date of issue: 2020-10-16 Filename: 191138_eng.pdf Germany: +49 621 776 1111 Pepperl+Fuchs Group Refer to "General Notes Relating to Pepperl+Fuchs Product Information". USA: +1 330 486 0001 Singapore: +65 6779 9091

Functional safety related parameters MTTFd 280 a Mission Time (TM) 20 a Diagnostic Coverage (DC) 0 % Switching output Output type 2 switch outputs PNP, NO , reverse polarity protected , short-circuit protected Operating current IL ≤ 100 mA Switching window ± 1 mm Switching hysteresis 0.4 mm Voltage drop ≤ 3 V Short-circuit protection pulsing Analog output Output type 1 current output: 4 ... 20 mA Load resistor ≤ 400 Ω Compliance with standards and directives Standard conformity Standards EN 60947-5-2:2007 IEC 60947-5-2:2007 Approvals and certificates UL approval cULus Listed, General Purpose, Class 2 Power Source CCC approval CCC approval / marking not required for products rated ≤36 V Ambient conditions Mechanical specifications Connection type 5-pin, M12 x 1 connector Degree of protection IP67 Material Housing ABS Target mild steel, e. g. 1.0037, SR235JR (formerly St37-2) Connection + UB - UB I Q S1 Q S2 4-20 mA IE8 Connection Assignment Inductive positioning system PMI104-F90-IE8-V15 Release date: 2020-03-23 Date of issue: 2020-10-16 Filename: 191138_eng.pdf Germany: +49 621 776 1111 Pepperl+Fuchs Group Refer to "General Notes Relating to Pepperl+Fuchs Product Information". USA: +1 330 486 0001 Singapore: +65 6779 9091

Wire colors in accordance with EN 60947-5-2 (brown) (white) (blue) (black) (gray) ≥ 4 ≥ 18 dimensions for the target object: Linearity range Measuring range

10 V/20 mA 0 V/4 mA

BT-F90-W Damping element for sensors of type F90, F112, and F166; side hole MH-F90 Mounting bracket for mounting of F90 sensors V15-G-2M-PVC Female cordset, M12, 5-pin, PVC cable V15-W-2M-PVC Female cordset, M12, 5-pin, PVC cable Inductive positioning system PMI104-F90-IE8-V15 Release date: 2020-03-23 Date of issue: 2020-10-16 Filename: 191138_eng.pdf Germany: +49 621 776 1111 Pepperl+Fuchs Group Refer to "General Notes Relating to Pepperl+Fuchs Product Information". USA: +1 330 486 0001 Singapore: +65 6779 9091

Release date: 2020-03-23 Date of issue: 2020-10-16 Filename: 191138_eng.pdf PMI104-F90-IE8-V15 Germany: +49 621 776 1111Pepperl+Fuchs Group Refer to "General Notes Relating to Pepperl+Fuchs Product Information". USA: +1 330 486 0001 Singapore: +65 6779 9091 Inductive positioning system Operating instructions

• Safety information
• S e n s o r v e r s i o n s The F90 linear position measurement system is available in 2 versions. In the PMI...-F90-IU-V1 version, the position measuring system transmits current and voltage signals proportional to the position of the damping element at the outputs. The PMI...-F90-IE8-V15 version offers a current signal as well as the option of teaching in two switching points directly at the sensor independently of one another at the press of a button, which is then indicated on two switching outputs. Two additional LEDs indicate the output states of the two switching outputs. Version PMI…-F90-IU-V1 Version PMI…-F90-IE8-V15 Output signals: 4 mA ... 20 mA and 2 programmable switching amplifiers
• Programming the PMI…-F90-IE8-V15 The rear of the PMI...-F90-IE8-V15 sensor has two small, slightly recessed push buttons for programming the switching points. The buttons are marked "teach in" and S1 for switching point S1 and S2 for switching point S2. To teach in a switching point, proceed as follows: - The position detection damping element must be placed at the relevant position, i.e. the switching point that you wish to teach in. - Press the corresponding push button for at least two seconds. The associated switching state LED starts flashing to indicate that the sensor is now in “teach mode”. - Press the button again to confir m the relevant switching point. The switching state LED then lights up constantly as long as the damping element is not moved. The switching point is now taught in and the associated switching point changes to an active state within an actuator adjustment range of ± 1 mm around the taught switching point.
• Damping element The linear position measurement system is adapted perfectly to the geometry of the damping elements offered in our product range.
• Installation and operation Instructions on installation - Flush installation is possible - to extend the measuring range, units from the -F90 linear position measurement system can be connected in series (both behind and adjacent to one another) without a minimum distance. - The minimum distance between the measuring fi eld (framed area on the sensor front) and mounting base or mounting elements on the damping element must be 3 mm.
• Operating information The specified measurement accuracy is achieved with an actuator distance of 1 to 3 mm. If the damping element leaves the measuring area (illustration below): - the last valid value is retained at the voltage output (PMI…-F90-IU-V1 only) until the damping element enters the valid area again. - the last valid value is retained for 0.5 seconds at the current output (all types). The output then switches to a fault current of 3.6 mA until the damping element enters the valid area again. Operation This product may not be used in applications where personal safety depends on the function of the device. This product is not a safety component as described in EU Machinery Directive. Only the current output or the voltage output may be used. The unused output must remain load free. If the switching point is not confirmed within 80 seconds, the sensor exits “teach mode” and continues operation with the previous values. When using other damping elements, always make sure that the active surface of the damping element has a width of exactly 8 mm and covers the entire width of the sensor. Warning Note Note ≥ 4 ≥ 18 Note Screw

Release date: 2020-03-23 Date of issue: 2020-10-16 Filename: 191138_eng.pdf PMI104-F90-IE8-V15 Germany: +49 621 776 1111Pepperl+Fuchs Group Refer to "General Notes Relating to Pepperl+Fuchs Product Information". USA: +1 330 486 0001 Singapore: +65 6779 9091 Inductive positioning system - the switching amplifiers set to basic st ate after 0.5 seconds ("normally open").

• Defining the measuring range / measured position The measured position of the damping element (actuator) is based on half of the width (center of the actuator). The measuring range starts and finishes when half the width of the actuator covers the measurement field marked on the sensor when the actuator makes a longitudinal movement (see left illustration above).
• Accessories Straight cable:V1-G-2M-PVC (4-wire) V15-G-2M-PVC (5-wire) Angled cable:V1-W-2M-PVC (4-wire) V15-W-2M-PVC (5-wire) Damping elements Mounting bracket BT-F90-W MH-F90 start of measuring range measured position end of measuring range labeled measuring area motion direction of actuator width w of actuator w/2 actuator