PM300DVA120

PM300DVA120_00 MITSUBISHI | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 6

Technical content

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE PM300DVA120 FEATURE

• 1 φ 300A, 1200V Current-sense IGBT for 20kHz switching
• Monolithic gate drive & protection logic
• Detection, protection & status indication circuits for over- current, short-circuit, over-temperature & under-voltage (P-F O available from upper leg devices)
• Acoustic noise-less 55kW class inverter application
• UL Recognized Yellow Card No. E80276(N) File No. E80271 APPLICATION General purpose inverter, servo drives and other motor controls PACKAGE OUTLINES Dimensions in mm 45.5 76 ±0.25 3–M8NUTS 2.54 2.54 2.54 2.54 38.5 2.5410.16 2.54 2.54 2.54 32.8 18 18 18 2828 3 ±0.5 2–φ3.5 106 ±0.25 120 4–R6.5 4–φ6.5 MOUNTING HOLES C2E1 E2 C1 P N 10– 0.64 LABEL +1.0 –0.5 5 : FNO 4 : VNC 3 : CNI 2 : SNR 1 : VN1 TERMINAL CODE N 5 : FPO 4 : VPC 3 : CPI 2 : SPR 1 : VP1 P

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 Symbol Parameter Applied between : VP1-VPC, VN1-VNC Applied between : CPI-VPC, CNI-VNC Applied between : FPO-VPC, FNO-VNC Sink current at FPO, FNO terminal VD VCIN VFO IFO Supply Voltage Input Voltage Fault Output Supply Voltage Fault Output Current VCES ±IC ±ICP PC Tj Collector-Emitter Voltage Collector Current Collector Current (Peak) Collector Dissipation Junction Temperature V D = 15V, VCIN = 5V TC = 25°C TC = 25°C TC = 25°C V A A W MAXIMUM RATINGS (Tj = 25°C, unless otherwise noted) INVERTER PART Symbol Parameter Condition Ratings Unit 1200 300 600 1260 –20 ~ +150 INTERNAL FUNCTIONS BLOCK DIAGRAM CONTROL PART V V V mA Condition Ratings Unit Ci Rfo Ci IN SR FO SINK SENS OUT2 OUT1 TEMP GND V CC Ci IN SR F O SINK SENS OUT2 OUT1 TEMP GND V CC AMP Rg Th AMP Rg E2 C2E1 C1 Rref VNC CNI SNR FNO VN1 VPC CPI SPR FPO VP1 Rfo Ci: 100pF, R fo: 1.5kΩ

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 Supply Voltage Protected by SC Supply Voltage (Surge) Module Case Operating Temperature Storage Temperature Isolation Voltage VCC(surge) TC Tstg Viso VVD = 13.5 ~ 16.5V, Inverter Part, Tj = 125°C Start Applied between : C1-E2, Surge value or without switching (Note-1) 60Hz, Sinusoidal, Charged part to Base, AC 1 min. 800 ParameterSymbol Condition Ratings VCC(PROT) 1000 –20 ~ +100 –40 ~ +125 2500 Unit V Vrms TOTAL SYSTEM CONTROL PART (Note-2) Fault output is given only when the internal SC, OT & UV protection. Fault output of OT protection operate by lower arm Fault output of OT, UV protection given pulse while over level. VD = 15V, VCIN = 5V Applied between : CPI-VPC, CNI -VNC –20≤ Tj ≤ 125°C, VD = 15V VD = 15V Base-plate Temperature detection, VD = 15V Vth(ON) Vth(OFF) SC toff(SC) OT OTr UV UV r IFO(H) IFO(L) tFO VSXR Circuit Current Input ON Threshold Voltage Input OFF Threshold Voltage Short Circuit Trip Level Short Circuit Current Delay Time Over Temperature Protection Supply Circuit Under-Voltage Protection Fault Output Current Minimum Fault Output Pulse Width SXR Terminal Output Voltage 1.5 2.0 118 100 12.0 12.5 1.8 5.1 –20 ≤ T j ≤ 125°C VD = 15V, VFO = 15V (Note-2) VD = 15V (Note-2) –20 ≤ Tj ≤ 125°C, Rin=6.8kΩ V A Trip level Reset level Trip level Reset level ID µs V mA ms V 1.8 2.3 125 12.5 0.01 5.6 mA— 1.2 1.7 380 111 11.5 1.0 4.5 ParameterSymbol Test Condition Max.Min. Typ. Unit Limits VN1-VNC VP1-VPC ELECTRICAL CHARACTERISTICS (Tj = 25°C, unless otherwise noted) INVERTER PART –IC = 300A, VD = 15V, VCIN = 5V VD = 15V, IC = 300A VCIN = 0V V µs V mA 3.30 3.25 3.50 2.3 0.3 1.0 3.4 1.2 Min. Typ. Max. Collector-Emitter Saturation Voltage Collector-Emitter Cutoff Current ParameterSymbol Test Condition VCE(sat) ICES VEC ton trr tc(on) toff tc(off) Limits 0.4 2.65 2.60 2.50 0.9 0.2 0.4 2.4 0.7 T j = 25°C Tj = 125°C FWDi Forward Voltage Switching Time VD = 15V, VCIN = 0V↔ 5V VCC = 600V, IC = 300A Tj = 125°C Inductive Load (upper and lower arm) VCE = VCES, VCIN = 5V Unit Tj = 25°C Tj = 125°C (Note-1) T C measurement point is below. (3mm depth at the center of the side of base plate) Tc

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 VCC VD VCIN(ON) VCIN(OFF) tdead fPWM Supply Voltage Control Supply Voltage Input ON Voltage Input OFF Voltage Arm Shoot-through Blocking Time PWM Input Frequency R th(j-c)Q Rth(j-c)F Rth(c-f) 5.88 10.8 Mounting part screw : M6 Main terminal screw : M8 Symbol Parameter Mounting torque Mounting torque Weight Test Condition Unit N • m N • m g Limits Min. Typ. Max. 3.92 8.83 4.90 9.81 720 MECHANICAL RATINGS AND CHARACTERISTICS Symbol THERMAL RESISTANCES 0.099 0.13 0.065 °C/W Inverter IGBT part (per 1/2 module) Inverter FWDi part (per 1/2 module) Case to fin, Thermal grease applied (per 1/2 module) Parameter Test Condition Unit Limits Min. Typ. Max. Junction to case Thermal Resistances Contact Thermal Resistance RECOMMENDED CONDITIONS FOR USE Symbol Recommended value UnitTest ConditionParameter Applied across C1-E2 terminals Applied between : VP1-VPC, VN1-VNC (Note-3) Applied between : CPI-VPC, CNI-VNC For IPM’s each input signals Using Application Circuit input signal of IPM, 3φ Sinusoidal PWM VVVF inverter ≤ 800 15 ± 1.5 ≤ 0.8 ≥ 4.0 ≥ 3.5 ≤ 20 V V V µs kHz (Note-3) With ripple satisfying the following conditions dv/dt swing ≤ ±5V/µs, Variation ≤ 2V peak to peak

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 3.0 Tj = 25°C Tj = 25°C Tj = 125°C VD = 15V VD = 15V Tj = 25°C Tj = 125°C VD = 17V 15V 13V 200 400 100 0 501234 300 0 4000 200 100 300 0 1701 3 1 4 1 5 1 6 10157 23 5 10272 3 5 10–1 100 101 101 102 103 0 1.0 2.0 3.0 101 10223 557 2 3 57 102 101 103 10–1 10–2 100 Tj = 25°C Tj = 125°C IC = 300A tc(off) tc(on) ton toff Tj = 125°C trr lrr VCC = 600V VD = 15V Tj = 25°C Tj = 125°C VCC = 600V VD = 15V OUTPUT CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT IC (A) COLLECTOR-EMITTER VOLTAGE VCE (V) COLLECTOR RECOVERY CURRENT –IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) CONTROL SUPPLY VOLTAGE VD(V) EMITTER-COLLECTOR VOLTAGE VEC (V) SWITCHING CHARACTERISTICS (TYPICAL) SWITCHING TIME (µs) COLLECTOR CURRENT IC (A) DIODE REVERSE RECOVERY CHARACTERISTICS (TYPICAL) REVERS RECOVERY TIME trr (µs) COLLECTOR RECOVERY CURRENT –IC (A) COLLECTOR-EMITTER SATURATION VOLTAGE VCE (sat) (V) COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (TYPICAL) COLLECTOR CURRENT IC(A) DIODE FORWARD CHARACTERISTICS (TYPICAL) REVERSE RECOVERY CURRENT lrr (A) PERFORMANCE CURVES

MITSUBISHI <INTELLIGENT POWER MODULES> PM300DVA120 FLAT-BASE TYPE INSULATED PACKAGE Jun. 2005 101 10–3 100 10–2 10–1 10–323 57 10–223 57 10–123 57 100 23 57 101 Single Pulse Per unit base = Rth(j – c)Q = 0.099°C/W 101 10–3 100 10–2 10–1 10–323 57 10–223 57 10–123 57 100 23 57 101 Single Pulse Per unit base = Rth(j – c)F = 0.13°C/W NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (IGBT per 1 element) NORMALIZED TRANSIENT THERMAL IMPEDANCE Zth (j – c) TIME (s) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (FWDi per 1 element) TIME (s)