PM210 SJM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 5

Technical content

Features

  • Very High Input IP3 of 28 dBm
  • Low Conversion Loss of 6.1 dB (850MHz RF, 740MHz LO, 0 dBm LO)
  • Low LO Power of -6 ~ 2dBm typical
  • Wide RF/IF Frequency Range 0.4 to > 1.5 GHz/40 ~250 MHz
  • Single-Ended Ports
  • RF- and IF-Port Impedance 50 ohms
  • Operating Voltage Range 3 to 6 V
  • Very Low Current Consumption of 7 mA typical
  • All Gold Metallization

Description

The PM210 is an all port,single-ended,generalpurposeup- and down- converter. It combines small conversion losses and excellent intermodulation characteristicswitha lowdemandofLO- andDC-power. The internallevelcontrolledLO-bufferenablesgoodperformanceover a widerangeofLOlevelinputs. ThemixerconfigurationallowsRF or IF feedto eitherpin1 or 6 andthus requiresa frequencyseparationcircuitonthepcboard. 1) Test Conditions : T=25°C, Supply Voltage=3V 2) Thermal Resistance _ Rth ≤ 40 C/W Absolute Maximum Ratings Functional Block Diagram 1) Stresses above the maximum values listed may cause permanent damage to the device. 2) MTTF is more than 100 years. 3) ESD : Electrostatic discharge sensitive device. Observe handling Precautions.

Applications

  • Up –or Down - Converters
  • Mobile Phones Receivers
  • Microphone Receivers
  • Mobile Phones Base Stations Parameter Port Symbol Value Unit min max Supply Voltage 4 VDD 0 6 V DC-Voltage at LO Input 3 V3 -3 0 , 5 V DC-Voltage at RF-IF Ports 1 , 6 V1,6 -0 , 5 +0 , 5 V Power into RF-IF Ports 1 , 6 Pin,RF 23 dBm Power into LO Input 3 Pin , LO 20 dBm Channel Temperature TCh 150 °C Storage Temperature Tstg -55 150 °C

Electrical Characteristics

No. Symbol Pin No. Symbol

1 RFor IF 6 IF or RF

2 GND 5 GND

3 Lo In 4 Vdd

4 Vdd

http://www.prewell.com 2 Ultra-linear Mixer SJM PREWELL PM210 Products and product information are subject to change without notice.Version 10 Preliminary Out/In If Vdd GND In/Out RF L3C3 LO In LO Input In/Out RF Out/In IF L1 C1 VddGND R_bias + Tantal Applications Information Test circuit / application example RF_850MHz / LO_740MHz / IF_110MHz_Application Circuit External components for cellular frequencies Capacitors Value Inductors Value C1 3.9pF L1 8.2nH C2 3.3pF L2 8.2nH C3 33pF L3 6.8nH C4 33pF L4 22nH R_Bias 0Ω(Vdd=3V) T1(Tantal) 10uF

http://www.prewell.com 3 Ultra-linear Mixer SJM PREWELL PM210 Products and product information are subject to change without notice.Version 10 Preliminary -8 -6 -4 -2 0 2 IIP3 (dB) LO POWER (dBm) -8 -6 -4 -2 0 2 Conversion LOSS (dB) LO POWER (dBm) -8 -6 -4 -2 0 2 Operating Current (mA) LO POWER (dBm) IIP3 1) ZS= ZL = 50 Ohm; unless otherwise specified Typical performance at cellular frequencies (Ta = 25°C / VDD= 3V / LO_0dBm) Conversion LossOperating Current Parameter / Test conditions Symbol min Typ max Unit Operating Current Iop - 7 - mA Conversion Loss Lc - 6.1 - dB SSB Noise Figure Fssb - 6.4 - dB 2Tone 3rdOrder IMD PRF1 = PRF2 = -3dBm fRF1 = 849.5MHz ; fRF2 = 850.5MHz ; fLO = 740MHz dIM3 - 62.1 - dBc 3rd Order Input Intercept Point IP3in - 28 - dBm P-1dB Input Power P-1dB 18.3 dBm LO Leakage at RF/IF-Port (1,6) PLO 1,6 - -9.13 - dBm

http://www.prewell.com 4 Ultra-linear Mixer SJM PREWELL PM210 Products and product information are subject to change without notice.Version 10 Preliminary Mounting Instructions 1 Use a large ground pad area with many plated through-holes as shown. 2 We recommend 1 oz copper minimum. 3 Measurement for our data sheet was made on 0.8mm thick FR-4 Board. 4 RF trace width depends on the board material and construction. 5 Add mounting screws near the part to fasten the board to a heatsink. 6 Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. Evaluation Board Layout (40x40 mm)

http://www.prewell.com 5 Ultra-linear Mixer SJM PREWELL PM210 Products and product information are subject to change without notice.Version 10 Preliminary Lead-free /RoHS Compliant / Green SOT23-6L Package Outline AA2 SEATIG PLANE SEE DETAIL A GAUGE PLANE 0.01[0.25] BSC L DETAIL A c Ø SYM. DIMENSIONS IN INCHES DIMENSIONS IN MM A1 0.000 - 0.006 0.00 - 0.15 e 0.037 0.95 e1 0.075 1.90 Ø 0° - 8° 0° - 8° Notes: 1. DIMENSION D DOES NOT INCLUDE MOLE FLASH, PROTRUSIONS OR GATE BURRS, DIMENSION E1 DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. 2. BASED FROM JEDEC MO-178 VARIATION AB. D E1 E e b X X X X Product Code Optional (Year Code or Blank) Optional(ICC)