PLT3450GB

PLT3450GB OSRAM | Alldatasheet

Document overview

• Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
• PDF pages: 16

Technical content

1 | Version 0.1 | 2023-06-21 Preliminary datasheet version www.osram-os.com PLT3 450GB Datasheet Preliminary datasheet version Published by ams-OSRAM AG Tobelbader Strasse 30, 8141 Premstaetten, Austria Phone +43 3136 500-0 ams-osram.com © All rights reserved

2 | Version 0.1 | 2023-06-21 Preliminary datasheet version Metal Can TO38 PLT3 450GB Blue Laser Diode in TO38 ICut Package

Applications

• Appliances & Tools - Entertainment - Functional Illumination - Medical Imaging - Outdoor & Industrial Lighting - Projection - Visualization

Features

• Typical emission wavelength: 450 nm - Efficient radiation source for cw and pulsed operation - Single mode semiconductor laser - High modulation bandwidth - Miniaturized TO38 ICut package - Laser diode isolated against package

3 | Version 0.1 | 2023-06-21 Preliminary datasheet version

Ordering Information

Type Peak output power Ordering Code typ. Popt PLT3 450GB 100 mW Q65113A4975

4 | Version 0.1 | 2023-06-21 Preliminary datasheet version Maximum Ratings Parameter Symbol Values Operating temperature Top min. max. -20 °C 70 °C Storage temperature Tstg min. max. -40 °C 85 °C Peak output power 1) Tcase = 25 °C Popt max. 110 mW Reverse voltage 2) Tcase = 25 °C VR max. 2 V Soldering temperature tmax = 10 sec TS max. 260 °C Operation outside these conditions may damage the device. Operation at maximum ratings may influence lifetime.

5 | Version 0.1 | 2023-06-21 Preliminary datasheet version Characteristics Popt = 100 mW; Tc = 25 °C Parameter Symbol Values Operating current Iop typ. max. 87 mA 120 mA Peak wavelength 3) λpeak min. typ. max. 440 nm 450 nm 460 nm Spectral bandwidth (FWHM) ∆λ typ. 1 nm Beam divergence (FWHM) parallel to pn-junction Θ‖ min. typ. max. 5 ° 8.4 ° 10 ° Beam divergence (FWHM) perpendicular to pn-junction Θ┴ min. typ. max. 18 ° 21.5 ° 25 ° Threshold current Ith typ. max. 12 mA 30 mA Forward voltage 4) VF typ. max. 5.2 V 6.5 V TE polarization PTE typ. 100:1 Modulation frequency f min. 100 MHz

6 | Version 0.1 | 2023-06-21 Preliminary datasheet version Relative Spectral Emission 5), 6) Popt = ƒ (λ) Beam Divergence 6) Popt = f (Θ)

7 | Version 0.1 | 2023-06-21 Preliminary datasheet version Optical Output Power 5), 6) Popt = f (IF) Operating Voltage 5), 6) VF = f (IF) Threshold Current Ith = f (Tc)

8 | Version 0.1 | 2023-06-21 Preliminary datasheet version Dimensional Drawing 7) Further Information: Approximate Weight: 141.0 mg ESD advice: ATTENTION – Observe Precautions For Handling – Electrostatic Sensitive Device.

9 | Version 0.1 | 2023-06-21 Preliminary datasheet version Electrical Internal Circuit Pin Description PIN 1 LD Anode PIN 2 Case PIN 3 LD Cathode

10 | Version 0.1 | 2023-06-21 Preliminary datasheet version Tray 7) 200 pieces per tray Barcode-Product-Label (BPL)

11 | Version 0.1 | 2023-06-21 Preliminary datasheet version Schematic Transportation Box 7) OHA02886 PACKVAR: R077Additional TEXT P-1+Q-1 Multi TOPLED Muster OSRAM Opto Semiconductors (6P) BATCH NO: (X) PROD NO: (9D) D/C: 11(1T) LOT NO: 21002199 123GH1234 0 24 5 (Q)QTY: 2000 0144 (G) GROUP:

260 C RT

240 C R

220 C R

MLBin3:Bin2: Q-1-20 Bin1: P-1-20 LSY T676 2 2a Temp ST R18 DEMY Barcode label Original packing label Box Dimensions of Transportation Box Width Length Height 215 ± 5 mm 265 ± 5 mm 95 ± 5 mm Notes Depending on the mode of operation, these devices emit highly concentrated visible and non visible light which can be hazardous to the human eye. Products which incorporate these devices have to follow the safety precautions given in IEC 60825-1. Subcomponents of this device contain, in addition to other substances, metal filled materials including silver. Metal filled materials can be affected by environments that contain traces of aggressive substances. There- fore, we recommend that customers minimize device exposure to aggressive substances during storage, production, and use. Devices that showed visible discoloration when tested using the described tests above did show no performance deviations within failure limits during the stated test duration. Respective failure limits are described in the IEC60810.

12 | Version 0.1 | 2023-06-21 Preliminary datasheet version Notes Important notes of operation for laser diode a) Electrical operation OSRAMs laser diodes are designed for maximum performance and reliability. Operating the laser diode above the maximum rating even for very short periods of time can damage the laser diode or reduce its lifetime. The laser diode must be operated with a suitable power supply with minimized electrical noise. The laser diode is very sensitive to electrostatic discharge (ESD). Proper precautions must be taken. b) Mounting instructions In order to maintain the lifetime of the laser diode proper heat management is essential. Due to the design of the laser diode heat is dissipated only through the base plate of the diode‘s body. A proper heat conduct- ing interconnection between the diodes base plate and the heat sink must be maintained. For further application related information please visit https://ams-osram.com/support/application-notes

13 | Version 0.1 | 2023-06-21 Preliminary datasheet version Disclaimer AMS OSRAM assumes no liability whatsoever for any use of this document or its content by recipient in- cluding, but not limited to, for any design in activities based on this preliminary draft version. AMS OSRAM may e.g. decide at its sole discretion to stop developing and/or finalizing the underlying design at any time. Attention please! The information describes the type of component and shall not be considered as assured characteristics. Terms of delivery and rights to change design reserved. Due to technical requirements components may contain dangerous substances. For information on the types in question please contact our Sales Organization. If printed or downloaded, please find the latest version on our website. Packing Please use the recycling operators known to you. We can also help you – get in touch with your nearest sales office. By agreement we will take packing material back, if it is sorted. You must bear the costs of transport. For packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to invoice you for any costs incurred. Product and functional safety devices/applications or medical devices/applications Our components are not developed, constructed or tested for the application as safety relevant component or for the application in medical devices. Our products are not qualified at module and system level for such application. In case buyer – or customer supplied by buyer – considers using our components in product safety devices/ applications or medical devices/applications, buyer and/or customer has to inform our local sales partner immediately and we and buyer and /or customer will analyze and coordinate the customer-specific request between us and buyer and/or customer.

14 | Version 0.1 | 2023-06-21 Preliminary datasheet version Glossary 1) Brightness: The brightness values are measured with a tolerance of ±11%. 2) Reverse Operation: This product is intended to be operated applying a forward current within the speci- fied range. Applying any reverse bias shall be avoided. 3) Wavelength: λpeak is measured with an internal reproducibility of ±0.3 nm (acc. to GUM with a cover- age factor of k = 3). 4) Forward Voltage: The forward voltages are measured with a tolerance of ±0.1 V. 5) Typical Values: Due to the special conditions of the manufacturing processes of semiconductor devic- es, the typical data or calculated correlations of technical parameters can only reflect statistical figures. These do not necessarily correspond to the actual parameters of each single product, which could dif- fer from the typical data and calculated correlations or the typical characteristic line. If requested, e.g. because of technical improvements, these typ. data will be changed without any further notice. 6) Testing temperature: TA = 25°C (unless otherwise specified) 7) Tolerance of Measure: Unless otherwise noted in drawing, tolerances are specified with ±0.1 and dimensions are specified in mm.

15 | Version 0.1 | 2023-06-21 Preliminary datasheet version

Revision History

0.0 2022-12-22 Initial Version 0.1 2023-06-21 Electro - Optical Characteristics (Diagrams) Type Designation System

16 | Version 0.1 | 2023-06-21 Preliminary datasheet version Preliminary datasheet version Published by ams-OSRAM AG Tobelbader Strasse 30, 8141 Premstaetten, Austria Phone +43 3136 500-0 ams-osram.com © All rights reserved