PIP VIGO | Alldatasheet

Document overview

  • Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
  • PDF pages: 2

Technical content

PIP series preamplifiers datasheet P a g e | 1 22/12/2021 VIGO System S.A. reserves the right to change these specifications at any time without notification. www.vigo.com.pl PIP series PIP is a series of programmable “smart” preamplifiers. Due to the modern internal configuration, it offers extreme flexibility combined with superior signal parameters and high reliability. Built-in voltage monitor allows to check and optimize the working con ditions (supply voltages, detector bias voltage, first and last stage output voltage offset etc.). There is also possible to change the gain, coupling (AC/DC), optimize the first stage transimpedance and manually or automatically suppress the voltage offset. Optimized parameters are stored into the internal EEPROM memory and automatically loaded after the power is on. Reset to default settings is available at any time. For detection module safety detector bias adjusting is blocked by default. User can request to enable this option while ordering. For proper operation PTCC-01 TEC controller is required. Specification (Ta = 20°C) Parameter Typical value Conditions, remarks Low cut-off frequency flo, Hz DC/10 user configurable by software High cut-off frequency fhi, Hz 150k/1.5M/20M 1.5M/15M/200M user configurable by software Transimpedance Ki, V/A 2.5k – 150k 0.5k – 30k digitally adjustable first stage transimpedance = 1 kΩ first stage transimpedance = 5 kΩ Output impedance Rout, Ω 50 Output voltage swing Vout, V ±1 RL = 50 Ω*) Output voltage offset Voff, mV max ±20**) Ambient operating temperature Ta, °C 10 to 30 Signal output socket SMA Power supply and TEC control socket LEMO (female) ECG.0B.309.CLN Mounting hole M4 Fan yes Parameters configurable by the user  Output voltage offset  Gain (in 40 dB range)  Bandwidth 150 kHz/1.5 MHz/20 MHz

1.5 MHz/15 MHz/200 MHz

 Coupling AC/DC  Detector’s parameters (temperature, reverse bias etc.) *) RL – load resistance **) Measured with equivalent resistor at the input instead of the detector, it is to avoid the environmental thermal radiation impact. Types of VIGO detectors that can be integrated with PIP preamplifier  Photoconductive PC-2TE, PC-3TE, PC-4TE  Phtoconductive optically immersed PCI-2TE, PCI-3TE, PCI-4TE  Photovoltaic PV-2TE, PVA-2TE, PV-3TE, PV-4TE  Photovoltaic optically immersed PVI-2TE, PVIA-2TE, PVI-3TE, PVI-4TE  Photovoltaic multiple junction PVM-2TE  Photovoltaic multiple junction optically immersed PVMI-2TE, PVMI-3TE, PVMI-4TE Code description Type flo fhi PIP – UC*) (DC/10 Hz) – LS*) (150 kHz/1.5 MHz/20 MHz) HS*) (1.5 MHz/15 MHz/200 MHz) *) User configurable by software. Power supply and TEC control socket LEMO (female) ECG.0B.309.CLN Function Symbol Pin number Fan and programmable preamp internal logic auxiliary supply FAN+ 1 Thermistor output (2) TH2 2 TEC supply input (–) TEC– 3 Power supply input (–) –Vsup 4 Ground GND 5 Power supply input (+) +Vsup 6 TEC supply input (+) TEC+ 7 Thermistor output (1) TH1 8 Biderictional data pin DATA 9 Included accessories  SMA-BNC, LEMO-DB9 cables Dedicated accessories  PTCC-01-BAS TEC controller + USB: TypeA-MicroB cable + AC adaptor  PTCC-01-ADV TEC controller + USB: TypeA-MicroB cable + AC adaptor  PTCC-01-OEM TEC controller + USB: TypeA-MicroB, KK2-POWER cables  OTA optical threaded adapter  DRB-2 base mounting system

PIP series preamplifiers datasheet P a g e | 2 22/12/2021 VIGO System S.A. reserves the right to change these specifications at any time without notification. www.vigo.com.pl Mechanical layout, mm Notes: 1. TO8 detector dimensions in the ”TO8 technical drawing”.