DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 7

Technical content

© Finisar Corporation October 2015 Rev. C1 Page 1 Product Specification

10 GBPS 1310NM PIN + PREAMP LC ROSA PACKAGE

  • LC ROSA PIN-1310-10LR-LC includes flex circuit
  • High performance InGaAs PIN photodiode with separate transimpedance amplifier
  • Low electrical parasitic TO46 package
  • Data rates up to 11.3Gbps
  • Separate PD supply for power monitoring
  • Low bias currents and voltages
  • Low power dissipation
  • IEEE 10G-BASE-LR applications The PIN-1310-10LR-LC uses a high -performance InGaAs PIN photo- detector packaged with a transimpedance amplifier designed to meet performance requirements for data rates up to 11.3Gbps data communication over singlemode and multi -mode optical fiber at 1310nm. Applications include Ethernet, Fiber Channel and ATM protocols. The optical assembly is designed to interface to single mode optical fiber. The PIN-1310-10LR-LC is designed to be paired with Finisar FP and DFB TOSA products (see data sheets for FP -1310 and DFB -1310 and products). The PIN is RoHS compliant per Directive 2011/65/EU PRODUCT SELECTION Part Number Description N-1310-10LR-LC pin LC ROSA, with separate PD bias, with flex circuit

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 2 I. Absolute Maximum Ratings Parameter Rating Storage Temperature -40 to +85°C Case Operating Temperature -10 to +85°C Lead Solder Temperature 260°C, 10 sec. Power Supply Voltage -0.5V to 4V Incident Optical Power +3 dBm average, +5 dBm peak Storage Temperature -40 to +85°C Notice Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operations section for extended periods of time may affect reliability. Notice The inherent design of this component causes it to be sensitive to electrostatic discharge (ESD). To prevent ESD-induced damage and/or degradation to equipment, take normal ESD precautions when handling this product

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 3 II. Electro-Optical Characteristics (3.0V<Vcc<3.6V, AC coupled to 50Ω (100Ωdifferential), -10°C<T<85°C unless otherwise specified, with flex) Notes: 1. PR is the average optical power at the fiber face. 2. PR,OMA is the peak to peak optical power at the fiber face (Optical Modulation Amplitude) ( ) −≡ ER ERPP R OMAR where ER is the extinction ratio (linear) of the optical source. 3. Bandwidth and Low Frequency Cutoff are measured with a small signal sinusoidal light source with –10dBm average power 4. Sensitivity is measured with an optical source with an extinction ratio of 6dB. For sensitivity measurements at 10.3125, 10.51875, 10.70923, 11.09573, 11.31764 Gb/s, PRBS 2^31-1, ER=6dB, BER < 10-12and with limiting of the TIA is assumed to be implemented at the front end of the post amplifier. Stress testing is done using a Circadiant test system 5. Rise/Fall times are corrected for optical source Rise/Fall times. 222 OPTICALMEASUREDTIA TTT −= 6. Value shown is with no external power supply filtering. 7. Group delay is a sensitive measurement to package interface, and includes the effects of PD, TIA and package. Measurement is made with TO leads as short as possible. 8. DJTIA is specified as contributed DJ by the TIA, obtained from 222 OPTICALTOTALTIA DJDJDJ −= 9. RJTIA is specified as contributed RJby the TIA, obtained from 222 OPTICALTOTALTIA RJRJRJ −= 10. The electrical performance of the ROSA is dependent upon the quality of the electrical connection between the TO can and the circuit board. AOC cannot guarantee all performance specifications for parts without the flex circuit attached. Parameters Test Condition Symbol Min. Typ. Max. Units Notes Data Rate DR 0.1 11.3 Gbps Supply Voltage 3.0 3.3 3.6 V Supply Current PR =0μW, RL =50ΩAC coupled ICC 35 60 mA 1 Optical Return Loss PR =-12dBm ORL 12 dB 1 Input Optical Wavelength λP 1260 1620 nm PD Responsivity λ = 1310nm Resp 0.8 0.85 A/W 1 PD Bias VPD 3.0 3.3 3.6 Maximum Average Input Power before Overload PMAX +1 +3 dBm Differential Output Voltage Swing PR,OMA= -12Bm, AC Coupled to RL =50Ω Vo(pk-pk) 100 600 mV 1,2 Differential Responsivity PR,OMA = -12dBm, AC Coupled to RL =50Ω T 1500 V/W 1,2 -3dB Optical/Electrical Bandwidth TA = 25°C BW 7.5 GHz 1,2,3 Low Frequency –3dB Cutoff BWLF 30 KHz 1,2,3 Output Impedance ZOUT 40 50 60 Ω Output Return Loss R0 =50Ω, DC 10≤GHZ S22 -7 dB Sensitivity DR = 10.3125Gbps S -16.5 dBm 4 Stressed Sensitivity Circadiant Test SSTRESS -12 dBm 4 Rise/Fall Time PR,OMA =-12dBm, (20%- 80%), TR/TF 45 ps 2,5 Differential Power Supply Rejection Ratio PR =0μW (Dark), 5MHz<F<2GHz PSRR 20 dB 1,6 Group Delay PR,OMA = -12dBm, AC Coupled to RL =50Ω 2MHz<F<6GHz Delay -50 50 ps 7

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 4 III. Environmental Specifications Parameter Symbol Min Typ Max Units Ref. Case Operating Temperature Top -10 85 °C Storage Temperature Tsto -40 85 °C IV. Mechanical Specifications (dimensions are in mm) PIN Description

1 Vcc

2 CASE

3 OUTP

4 OUTN

5 CASE

6 VPD

Ω

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 5 INTERFACE EXAMPLE Optional 100Ω differential termination for high impedance limiting amplifiers is shown in red. Recommended bias network Note, better performance will be obtained if a ferrite bead is used in place of the inductor. VCC VCC OUTN OUTP Case 50Ω 50Ω Limiting Amp VPD 100Ω 100nF Note: 100Ω resistor only needed with high impedance limiting amplifiers 100Ω 20x RSSI ~ 1V/mW VPD VCC VCC OUTN OUTP Case 50Ω 50Ω Limiting Amp VPD 100Ω 100nF Note: 100Ω resistor only needed with high impedance limiting amplifiers 100Ω 20x RSSI ~ 1V/mW VPD 22uH 100uF 100nF IN OUT22uH 100uF 100nF IN OUT

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 6 Mounting Dimensions (in mm)

PIN-1310-10LR-LC Product Specification © Finisar Corporation October 2015 Rev. C1 Page 7 V. References 1. Directive 2011/65/EU of the European Parliament and of the Council, “on the restriction of the use of certain hazardous substances in electrical and electronic equipment”. Certain products may use one or more exemption as allowed by the Directive. VI. Revision History Revision Date Description B00 10/14/2014 Converted to Finisar standard format. C1 10/20/2015 Updated logo and RoHS statement. VII. For More Information Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com