DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 16
Technical content
Features
Î ÎDP 1:3 De-Mux or 3:1 Mux switch with 4 high speed differential, AUX/DDC, HPD and CAB_DET channels Î Î Pin selection for 1:3 DEMUX or 3:1 MUX Î ÎHDMI 3:1 Mux switch with 4 high speed differential, DDC and HPD channels Î Î HDMI-mode only supports HDMI-sink application, not support HDMI-source application. Î Î Pin selection for DP mode or HDMI mode Î Î All ports support up to DP1.2 at 5.4Gb/s or HDMI 2.0 at 6Gb/s Î Î Supports manual switching or HPD auto priority selection in 1:3 DEMUX, in DP mode Î Î Low current consumption Î Î 3.3V power supply Î Î ESD protection on all I/O pins for 2kV HBM Î Î Package: 0 pin TQFN (5x9mm)
Description
Pericom Semiconductor’s PI3WVR31310A is a 3:1 Mux or 1:3 Demux high speed passive switch supporting DP 1.2, HDMI 1.4, HDMI 2.0. At DEMUX mode, all three output ports support auto port priority selection by detecting HPD1/2/3 input or manual selection. At MUX mode, HPD1/2/3 will change from input to output, there is no auto port priority selection. Application Î ÎNotebook, Monitor, Switch box or TV sink application PI3WVR31310A DP/HDMI 1:3 De-mux/Mux switches Block Diagram Control Block CAB_SRC HPD_SRC 120K/uni03A9 120K/uni03A9 HPD1 HPD2 CAB_1 AUXP AUXN SDA SCL AUX1P/SCL1 AUX1N/SDA1 D[0:3]P1 D[0:3]N1 D[0:3]P D[0:3]N D[0:3]P3 D[0:3]N3 Port select OEB PRI_SEL SEL1 SEL0 DP_HDMI DEMUX_MUX Control & Status Register 120K/uni03A9 HPD3 CAB_2 AUX2P/SCL2 AUX2N/SDA2 D[0:3]P2 D[0:3]N2 120K/uni03A9 MUX DEMUX CAB_3 AUX3P/SCL3 AUX3N/SDA3 [1] [1] [1] [1] 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Note: 1. The 120kΩ pull down resistor is not always on. Pin Configuration: TQFN-60 52 51 22 23 24 25 2621 27 30 29 28 54 5356 5558 5760 59 GND TQFN-60 5x9 mm VDD D0P D0N D1P D1N D2P D2N D3P D3N SEL1 SEL0 HPD_SRC CAB_SRC CAB_3 HPD3 DEMUX_MUX AUXP AUXN SCL VDD DP_HDMI AUX3N/SDA3 AUX3P/SCL3 CAB_2 HPD2 AUX2N/SDA2 AUX2P/SCL2 CAB_1 HPD1 VDD D0P2 D0N2 D1P2 D1N2 D2P2 D2N2 D3P2 D3N2 VDD AUX1P/SCL1 AUX1N/SDA1 D0P1 D0N1 D1P1 D1N1 D2P1 D2N1 D3P1 D3N1 PRI_SEL OEB SDA D3P3 D3N3 D2P3 D2N3 D1P3 D1N3 D0P3 D0N3 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. pin# pin Name Signal Type Description D0P, D1P, D2P, D3P, D0N, D1N, D2N, D3N IO 4 differential pair I/O (DP or HDMI) 60, 58, 56, 54, 59, 57, 55, D0P1, D1P1, D2P1, D3P1, D0N1, D1N1, D2N1, D3N1 IO 4 differential pair I/O (DP or HDMI) for port 1 49, 47, 45, 43, 48, 46, 44, D0P2, D1P2, D2P2, D3P2, D0N2, D1N2, D2N2, D3N2 IO 4 differential pair I/O (DP or HDMI) for port 2 41, 39, 37, 35, 40, 38, 36, D0P3, D1P3, D2P3, D3P3, D0N3, D1N3, D2N3, D3N3 IO 4 differential pair I/O (DP or HDMI) for port 3 Pin Description 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. pin# pin Name Signal Type Description 31, 27, 23, 32, 28, AUX1N/SDA1, AUX2N/SDA2, AUX3N/SDA3, AUX1P/SCL1, AUX2P/SCL2, AUX3P/SCL3 IO AUX (DP) or DDC (HDMI) input from three ports 18, AUXN, AUXP IO AUX output 20, SDA, SCL IO DDC output 30, 26, 15, HPD1, HPD2, HPD3, HPD_SRC IO When DEMUX_MUX = low (1:3 DEMUX mode), HPD1_2_3 are inputs, HPD_SRC is output; When DEMUX_MUX = high (3:1 MUX mode), HPD1_2_3 are outputs, HPD_SRC is input 29, 25, 14, CAB_1, CAB_2, CAB_3, CAB_SRC IO CAB_1, CAB_2, CAB_3, CAB_SRC
51 OEB I OEB=0, device active; OEB=1, device shut down
52 PRI_SEL I
PRI_SEL is for priority selection as in priority-selection-table, but only for 1:3 DEMUX mode. PRI_SEL has internal 100K divider between VDD and GND for middle-state with VDD/2.
16 DEMUX_MUX I DEMUX_MUX is for HPD direction selection, see truth table
22 DP_HDMI I DP port or HDMI port, see truth table
11 SEL0 I Port selection pins, see truth table
10 SEL1 I Port selection pins, see truth table
1, 21, 33, 50 VDD Power 3.3V VDD Center Pad GND Ground Bottom GND EPAD 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Pin mapping for dual mode DP source DEMUX to DP output DP mode HDMI/DVI mode WVR31310A input pins WVR31310A port1 output WVR31310A port2 output WVR31310A port3 output DP mode ML_lan0(P) TX2+ D0P D0P1 D0P2 D0P3 ML_lan0(P) ML_lan0(N) TX2- D0N D0N1 D0N2 D0N3 ML_lan0(N) ML _lan1(P) TX1+ D1P D1P1 D1P2 D1P3 ML _lan1(P) ML_lan1(N) TX1- D1N D1N1 D1N2 D1N3 ML_lan1(N) ML_lan2(P) TX0+ D2P D2P1 D2P2 D2P3 ML_lan2(P) ML_lan2(N) TX0- D2N D2N1 D2N2 D2N3 ML_lan2(N) ML_lan3(P) TXC+ D3P D3P1 D3P2 D3P3 ML_lan3(P) ML_lan3(N) TXC- D3N D3N1 D3N2 D3N3 ML_lan3(N) Function Description Default input format is DP. DP_HDMI can select between DP or HDMI input. In Demux mode, there are 120K pull down in HPD1/HPD2/HPD3 pins. In Mux mode, there is 120K pull down in HPD_SRC pin. Output port can be selected by manual or automatically in DEMUX mode. Automatic port selection is done by detection of HPD presence from the output ports. If multiple HPD are detected, port selection depends on a priority scheme defined by PRI_SEL pin. There can be 3 priority schemes. When PRI_SEL=low, the port priority order is port1/port2/port3; when PRI_SEL=high, the port priority order is port2/port3/port1; when PRI_SEL=M (open), the port priority order is port3/port1/port2. When port 1 or port 2 or port 3 is selected in DP application, and CAB=LOW, AUX/DDC input pins are now AUX channel. AUXP will have 100Kohm resistor to GND while AUXN will have 100Kohm resistor to VDD in external port side. Max. AUX data rate can be 720Mb/s. DDC switch inside is off. When port 1 or port 2 or port 3 is active in dual mode DP or HDMI application, and CAB=HIGH, AUX/DDC input pins are now DDC channel. AUX switch inside is off, DDC switch is on. The DDC switch can support 5V input, and output Vpass is less than 3.3V limit. HPD is CMOS buffer, and support 5v inputs. When used as DEMUX, There’re 120kΩ pull-down resistors inside connected to HPD1, HPD2, HPD3 as input, and when used as MUX, 120k resistor connected to HPD_SRC as input. 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Truth Table DEMUX_MUX HPD_SRC HPD1/2/3 0 (DEMUX) output input 1 (MUX) input output DEMUX_MUX DP_HDMI Mode
0 DP Mode
1 HDMI Mode
PRI_SEL (priority selection) HPD/CAB_DET D[0:3]P, D[0:3]N, AUX/DDC 0 0 NC HPD1/CAB_1 Port 1 0 1 NC HPD2/CAB_2 Port 2 1 0 NC HPD3/CAB_3 Port 3 1 1 Auto-selection See priority table See priority table SLE1/SEL0 in 1:3 DP modes DP_HDMI AUX and DDC PORT DP_HDMI CAB_1 CAB_2 CAB_3 AUXP AUXN SCL SDA When Port1 Selected 0 0 x x AUX1P AUX1N Hi-Z Hi-Z 0 1 x x Hi-Z Hi-Z SCL1 SDA1 1 1 x x Hi-Z Hi-Z SCL1 SDA1 When Port2 Selected 0 x 0 x AUX2P AUX2N Hi-Z Hi-Z 0 x 1 x Hi-Z Hi-Z SCL2 SDA2 1 x 1 x Hi-Z Hi-Z SCL2 SDA2 When Port3 Selected 0 x x 0 AUX3P AUX3N Hi-Z Hi-Z 0 x x 1 Hi-Z Hi-Z SCL3 SDA3 1 x x 1 Hi-Z Hi-Z SCL3 SDA3 SEL1 SEL0 PRI_SEL (priority selection) HPD D[0:3]P, D[0:3]N, AUX/DDC 0 0 NC HPD=HPD1, HPD2/3=0 Port 1 0 1 NC HPD=HPD2, HPD1/3=0 Port 2 1 0 NC HPD=HPD3, HPD1/2=0 Port 3 1 1 NC NC NC SLE1/SEL0 in 3:1 HDMI mode and DP mode 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. PRI_SEL (Priority order) HPD1 HPD2 HPD3 D0P D1P D2P D3P D0N D1N D2N D3N 0 0 0 0 Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z 0 1 x x D0P1 D1P1 D2P1 D3P1 D0N1 D1N1 D2N1 D3N1 0 0 1 x D0P2 D1P2 D2P2 D3P2 D0N2 D1N2 D2N2 D3N2 0 0 0 1 D0P3 D1P3 D2P3 D3P3 D0N3 D1N3 D2N3 D3P3 M 0 0 0 Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z M 1 x 0 D0P1 D1P1 D2P1 D3P1 D0N1 D1N1 D2N1 D3N1 M 0 1 0 D0P2 D1P2 D2P2 D3P2 D0N2 D1N2 D2N2 D3N2 M x x 1 D0P3 D1P3 D2P3 D3P3 D0N3 D1N3 D2N3 D3P3 1 0 0 0 Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z Hi-Z 1 1 0 0 D0P1 D1P1 D2P1 D3P1 D0N1 D1N1 D2N1 D3N1 1 x 1 x D0P2 D1P2 D2P2 D3P2 D0N2 D1N2 D2N2 D3N2 1 x 0 1 D0P3 D1P3 D2P3 D3P3 D0N3 D1N3 D2N3 D3P3 Note: M= VDD/2 or open (with internal VDD/2) Note: For priority selection control, when PRI_SEL = 0, the order is port1/port2/port3; when PRI_SEL = 1, the order is port2/port3/port1; when PRI_SEL = M, the order is port3/port1/port2. Priority Selection Table PRI_SEL (Priority order) HPD1 HPD2 HPD3 HPD_SRC CAB_SRC AUXP/AUXN SDA/SCL 0 0 0 0 0 Hi-Z Hi-Z Hi-Z 0 1 x x HPD1 CAB1 AUX1P/AUX1N SDA1/SCL1 0 0 1 x HPD2 CAB2 AUX2P/AUX2N SDA2/SCL2 0 0 0 1 HPD3 CAB3 AUX3P/AUX3N SDA3/SCL3 M 0 0 0 0 Hi-Z Hi-Z Hi-Z M 1 x 0 HPD1 CAB1 AUX1P/AUX1N SDA1/SCL1 M 0 1 0 HPD2 CAB2 AUX2P/AUX2N SDA2/SCL2 M x x 1 HPD3 CAB3 AUX3P/AUX3N SDA3/SCL3 1 0 0 0 0 Hi-Z Hi-Z Hi-Z 1 1 0 0 HPD1 CAB1 AUX1P/AUX1N SDA1/SCL1 1 x 1 x HPD2 CAB2 AUX2P/AUX2N SDA2/SCL2 1 x 0 1 HPD3 CAB3 AUX3P/AUX3N SDA3/SCL3 Note: M= VDD/2 or open (with internal VDD/2) 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners.
Electrical Characteristics
Recommended Operation Conditions VDD = 3.3V ±10%, Min and Max apply for TA between -40oC to 85oC Typical values are referenced to TA = 25oC Parameter Description Test Conditions Min. Ty p. Max. Unit VDD Operating Voltage 3.0 3.3 3.6 V IDD VDD supply current VDD=3.3V 1 mA Istd Supply current when OEB disable HDMI Mode VDD=3. 6 V, OE B =h ig h DP_HDMI=1 0.7 mA Supply current when OEB disable DP Mode VDD=3. 6 V, OE B =h ig h DP_HDMI=0 10 uA High Speed Channel Input Voltage (DP Mode) High Speed Channel Input Voltage (HDMI Mode) DDC and HPD channels Input Voltage DC Output Current Power Dissipation Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indi - cated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Maximum Ratings (Above which useful life may be impaired. For user guidelines not tested.) Parameter Description Test Conditions Min. Ty p. Max. Unit OEB, SEL1, SEL0 IIH High level digital input current V IH =VDD -10 40 μA IIL Low level digital input current V IL = GND -10 10 μA VIH High level digital input voltage 2.0 V VIL Low level digital input voltage 0 0.8 V DEMUX_MUX IIH High level digital input current V IH =VDD -10 40 μA IIL Low level digital input current V IL = GND -10 10 μA VIH High level digital input voltage 2.7 V VIL Low level digital input voltage 0 0.8 V DP_HDMI Rpd Inter Pull-down resistor on DP_HDMI 100 kΩ V IH High level digital input voltage 0.7Vdd V VIL Low level digital input voltage 0 0.3Vdd V 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Parameter Description Test Conditions Min. Ty p. Max. Unit HPD_SRC (when HPD_SRC is output, HPD 1, 2, 3 are inputs) VIH High level digital input voltage V DD=3.3V 2.0 V VIL Low level digital input voltage V DD=3.3V 0 0.8 V VOL_HPD_SRC Buffer Output Low Voltage I OL = 4 mA 0.4 V VOH_HPD_SRC Buffer Output Low Voltage I OH = 4 mA 2.4 V HPD_Sink (when HPD_SRC is input, HPD 1, 2, 3 are as sink outputs) VIH High level digital input voltage VDD=3.3V 2.0 V VIL Low level digital input voltage 0 0.8 V VOL_HPD_Sink Buffer Output Low Voltage I OL = 4 mA 0.4 V VOH_HPD_Sink Buffer Output Low Voltage I OH = 4 mA 2.4 V CAB ILK Input leakage current Switch is off, Vin=5.5V -50 50 uA CIO Input/Output capacitance when passive switch on 10 pF RON Passive Switch resistance IO = 3mA, VO = 0.4V 25 50 Ω Vpass Switch Output voltage VI=3. 3V, II=100uA 3.0 3.5 4.0 V CI(source) Source side CAB capacitance VI peak-peak = 1V, 100 KHz 3.5 pF CI(sink) Sink side CAB capacitance when 6.5 pF SDA/SCL,SDA1/SCL1, SDA2/SCL2 , SDA3/SCL3 (passive switch) ILK Input leakage current DDC switch is off, Vin=5.5V -50 50 uA CIO Input/Output capacitance when passive switch on V I peak-peak = 1V, 100 KHz 10 pF RON Passive Switch resistance IO = 3mA, VO = 0.4V 25 50 Ω Vpass Switch Output voltage VI=5.0V, II=100uA VDD=3.3V 1.5 2.0 2.5 V CI(source) Source side DDC capacitance ( passive switch off. ) V I peak-peak = 1V, 100 KHz 2.5 pF CI(sink) Sink side DDC capacitance ( pas- sive switch off. ) V I peak-peak = 1V, 100 KHz 9 pF AUXP , AUXN, AUXnP/SCLn, AUXnN/SDAn ILK Input leakage current DDC switch is off, Vin=5.5V -50 50 uA CIO Input/Output capacitance when passive switch on V I peak-peak = 1V, 100 KHz 7 pF RON Passive Switch resistance IO = 3mA, VO = 0.4V 5 15 Ω Vpass Switch Output voltage VI=5. 5 V, II=100uA VDD=3.3V 3.0 4.0 4.5 V CI(source) Source side capacitance ( passive switch off. ) V I peak-peak = 1V, 100 KHz 2.5 pF 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Parameter Description Test Conditions Min. Ty p. Max. Unit CI(sink) Sink side capacitance ( passive switch off. ) VI peak-peak = 1V, 100 KHz 3.5 pF High Speed Channel (D[0:3]P/N – D[0:3]P1N1, D[0:3]P/N – D[0:3]P2N2) VIK Clamp Diode Voltage (HS Chan- nel) V DD = Max., IIN = –18mA –1.6 –1.8 V IIH Input HIGH Current VDD = Max., VIN = VDD ±10 µA IIL Input LOW Current VDD = Max., VIN = GND ±10 RON_HS On resistance between input to out- put for high speed signals V INPUT,cm = 0V to 0.8V, VINPUT, diff < 1.0Vp-p,diff, VDD = 3.0V, IINPUT = 20mA 8 12 Ohm VINPUT,cm = 2.2V to 3.1V, VINPUT, diff < 1.2Vp-p,diff, VDD = 3.0V, IINPUT = 20mA 8 12 Ohm Input signal voltage range HDMI MUX mode Channel on 2.4 3.3 V HDMI MUX mode Channel off 0 3.3 V Note: High speed channel does not support Ioff when VDD=0 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Dynamic Electrical Characteristics Parameter Description Test Conditions Min. Ty p.(1) Max. Unit SCL, SDA channel, AUX channel, CAB channel (passive switch) tpd(DDC) Propagation delay from SCLn/SDAn to SCL/SDA or SCL/SDA to SCLn/SDAn In passive SW on. C L = 10pF, in passive switch 5 nsCL = 10pF, in active switch (1.5k to 5k pull high, 10pf to GND) Control and Status Pins (HPDn, HPD_SRC) tpd(HPD) Propagation delay (from HPDx to the active port of HPD_SRC, high to low) C L = 10pF, manual selection mode; auto mode refer to auto timing 10 ns tsx(HPD) Switch time (from port select to the latest HPD ) 5 us X TALK Crosstalk on High Speed Channels See Fig.1 for Measurement Setup f = 2.7 GHz -26 -23 dB f = 3.0 GHz -24 -21 O IRR OFF Isolation on High Speed Channels See Fig. 2 for Measurement Setup f = 2.7 GHz -21 -19 f = 3.0 GHz -21 -19 I LOSS Differential Insertion Loss on High speed channels @5.4Gbps (see figure 3, Vcom = 0V) -1.8 -1.6 dB I LOSS Differential Insertion Loss on High Speed HDMI Channels @6Gbps (see figure 3, Vcom = 3.0V) -2.5 dB R loss Differential Return Loss on High speed channels @ 2.7GHz (5.4Gbps) -18 -15 dB BW_Dx± Bandwidth -3dB for Main High speed path (Dx±) See figure 3 5.0 5.4 GHz BW_Dx± Bandwidth -3dB for Main high speed HDMI path (Dx±) See figure 3 4.7 5.0 GHz BW_AUX Bandwidth -3dB for AUX See figure 3 1.2 1.5 GHz Tsw a-b time it takes to switch from port A to port B Manual selection 1 us Tsw b-a time it takes to switch from port B to port A Manual selection 1 us T startup Vdd valid to channel enable Manual selection 10 us Twakeup Enabling output by changing OEB from High to Low Manual selection 10 us 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Fig 1. Crosstalk Setup Fig 2. Off-isolation setup BALANCED PORT1 DUT BALANCED PORT2 BALANCED PORT1 BALANCED PORT2 DUT BALANCED PORT1 BALANCED PORT2 DUT Fig 3. Differential Insertion Loss 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. HPD timing waveform (DEMUX mode) HPD from selected-active port HPD_SRC t1 (<2ms) t1 is the IRQ-HPD (sink) from selected-active port Priority Setting HPD_SRC t3 (1s) All Channels Hi-Z Event of priority setting change Low for HPDs other than HPDx. HPDx is the HPD of the only port with plugging-in HPDx HPD_SRC All Channels Hi-Z HPDx port is active Selected port is active Selected port is active Selected port is active Selected port is active t1 (<2ms) New selected port is active t3 (1s) All Channels Hi-Z Fig 4. HPD timing t1. HPD_SRC low and the active of selected port will follow t1, if t1 further extended less than t2 (125ms) when auto switch and manual switch Fig 5. HPD timing t3. All channels” include DP-HDMI data, AUX, DDC, HPD and CAB_DET when auto switch Fig 6. HPD timing t3 when auto switch 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. t2 (2s) t3 (1s) All Channels Hi-Z New selected port is active HPD_SRC HPD from selected-active Port HPD-high for at least one other port HPD_SRC All Channels Hi-Z HPD from selected-active port HPD_SRC Selected port is active HPD-high for at least one other port HPD of prioritized Port t3 (1s) t3 (1s)Selected port is active Prioritized port is active HPD-low for all other ports Selected port is active Selected port stays active with all channels connected Fig 7. HPD timing when auto switch Fig 8. HPD timing when auto switch Fig 9. HPD timing when auto switch and manual switch 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. Parameter Test Conditions Min. Ty p.* Max. Unit HPD auto switching timing HPD pulse duration when treated as an IRQ –t1 (Figure 4) 2 ms Propagation delay of HPDx Desertion –t2 (Figure 7) 1.2s 2s 3s s HPD_SRC low duration when the outputs are switched –t3(Figure 5, 6, 7, 8, 10); Propagation delay of HPDx assertion (Figure 8) 0.6s 1s 1.5s s t3 (1s) All Channels active to new selected port HPD_SRC Manually set port-priority All channels Hi-Z t1 (<2ms) Selected port is active New Selected port is active Event of priority change Fig10. HPD timing t3. All channels when auto switch Port Selection by Manual Mode 15-0139
DP/HDMI 1:3 De-mux/Mux switches www.pericom.com 10/30/15 All trademarks are property of their respective owners. 14-0044
Ordering Information
Ordering Code Package Code Package Description PI3WVR31310AZLE ZL 60-Pin, (TQFN) 5X9mm PI3WVR31310AZLEX ZL 60-Pin, (TQFN) 5X9mm, Tape & Reel Notes:
- Thermal characteristics can be found on the company web site at www.pericom.com/packaging/
- "E" denotes Pb-free and Green
- Adding an "X" at the end of the ordering code denotes tape and reel packaging Packaging Mechanical: ZL60 Pericom Semiconductor Corporation • 1-800-435-2336 • www .pericom.com Note: For latest package info, please check: http://www.pericom.com/support/packaging/packaging-mechanicals-and-thermal-characteristics/ 15-0139