PI3A4624 PERICOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 8

Technical content

Features

  • Low On-Resistance: 0.4Ω (+2.7V Supply)
  • RON Matching: 0.09Ω Max.at 25 °C
  • RON Flatness: 0.1Ω Max. (+3.0V Supply) at 25 °C
  • Low 2nA Input Leakage at 25 °C
  • +1.5V to +3.6V Single-Supply Operation
  • Fast Switching Time: 40ns Max.
  • -41dB Off-Isolation at 100KHz
  • TTL/CMOS Logic Compatible
  • Low Power Consumption: 5µW
  • Packaging (Pb-free & Green available): – 6-pin Small Compact SOT-23 (T) – 6-pin No Lead (TDFN) (ZC)

Applications

  • Communication Circuits
  • Cellular Phones
  • Audio and Video Signal Routing
  • Portable Battery-Operated Equipment
  • Data Acquisition Systems
  • Computer Peripherals
  • Telecommunications
  • Relay Replacement
  • Wireless Terminals and Peripherals
  • Hard Drives
  • Modems Block Diagram, Pin Configuration Top View Switches shown for Logic “0” input IN VCC GND NC NO COM5 IN VCC GND NC NO COM SOT23 TDFN Truth Table Logic NC NO

0 ON OFF

1 OFF ON

3.0V , SOTiny™ 0.4Ω Single-Supply SPDT Analog Switch

2 PS8712A 07/07/04

V oltages Referenced to GND or 30mA, whichever occurs first Peak Current, COM, NO, NC Notes: 1. Signals on NC, NO, COM, or IN exceeding VCC or GND are clamped by internal diodes. Limit forward diode current to 30mA. Caution: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Thermal Information Continuous Power Dissipation Electrical Specifications - Single +3.3V Supply (VCC = +3.3V ± 10%, GND = 0V , VIH = 1.4V , VIL = 0.5V) Parameter Symbol Conditions Package Temp. (°C) Min.(1) Typ.(2) Max.(1) Units Analog Switch Analog Signal Range (3) VANALOG Full 0 VCC V On-Resistance RON VCC = 2.7V , ICOM = 100mA, VNO or VNC = +1.5V 25 0.4 0.5 Ω SOT23 Full 0.5 TDFN 0.6 On-Resistance Match Between Channels(4) ∆RON 25 0.08 Full 0.09 On-Resistance Flat- ness(5) RFLAT(ON) VCC = 2.7V , ICOM = 100mA, VNO or VNC = 0.8V , 2.0V 25 0.1 Full 0.1 NO or NC Off Leakage Current(6) INO(OFF) or INC(OFF) VCC = 3.3V , VCOM = 0V , VNO or VNC = +2.0V 25 –1 1 nA Full –10 10 COM On Leakage Cur- rent(6) ICOM(ON) VCC = 3.3V , VCOM = +2.0V , VNO or VNC = +2.0V 25 –2 2 Full –20 20

3.0V , SOTiny™ 0.4Ω Single-Supply SPDT Analog Switch

3 PS8712A 07/07/04

Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY , not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ∆RON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. 6. Leakage parameters are 100% tested at maximum rated hot temperature and guaranteed by correlation at +25ºC. 7. Off Isolation = 20log10 [ VCOM / (VNO or VNC) ]. See Figure 4. 8. Between any two switches. See Figure 5. Electrical Specifications - Single +3.3V Supply (continued) (VCC = +3.3V ± 10%, GND = 0V , VIH = 1.4V , VIL = 0.5V) Parameter Symbol Conditions Temp. (°C) Min.(1) Typ.(2) Max.(1) Units Logic Input Input High V oltage VIH Guaranteed Logic High Level Full 1.4 VInput Low V oltage VIL Guaranteed Logic LowLevel 0.5 Input Current with V oltage High IINH VIN = 1.4V , all others = 0.5V –1 1 µAInput Current with V oltage Low IINL VIN = 0.5V , all others = 1.4V –1 1 Dynamic Turn-On-Time tON VCC = 3.3V , VNO or VNC = 2.0V , Figure 1 25 20 nsFull 40 Turn-Off-Time tOFF 25 10 Full 20 Charge Injection(3) Q CL =1nF, VGEN = 0V , RGEN = 0Ω, Figure 2 25 40 pC Off Isolation(7) OIRR RL = 50Ω, f = 100 KHz, Figure 3 -27 dBCrossTalk(8) XTALK RL = 50Ω, f = 100 KHz, Figure 4 -41 NC or NO Capacitance CNC/NO (OFF) f = 1 MHz, Figure 5 pFCOM Off Capacitance CCOM(OFF) 75 COM On Capacitance CCOM(ON) f = 1 MHz, Figure 6 200 Supply Power-Supply Range VCC Full 1.5 3.6 V Positive Supply Current ICC VCC = 3.6V , VIN = 0V or VCC 100 nA

3.0V , SOTiny™ 0.4Ω Single-Supply SPDT Analog Switch

4 PS8712A 07/07/04

Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY , not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. Electrical Specifications - Single +2.5V Supply (VCC = +2.5V ± 10%, GND = 0V , VIH = 1.4V , VIL = 0.5V) Parameter Symbol Conditions Temp. (°C) Min.(1) Typ.(2) Max.(1) Units Analog Switch Analog Signal Range(3) VANALOG 0 VCC V On-Resistance RON VCC = 2.5V , ICOM = –8mA, VNO or VNC = 1.8V 25 0.5 Ω Full 0.6 On-Resistance Match Between Channels(4) ∆RON VCC =2.5V , ICOM = –8mA, VNO or VNC = 0.8V , 1.8V 25 0.1 Full 0.1 On-Resistance Flat- ness(5) RFLAT(ON) 25 0.1 Full 0.1 Dynamic Turn-On-Time tON VCC = 2.5V , VNO or VNC = 1.8V , Figure 1 25 30 ns Full 50 Turn-Off-Time tOFF 25 15 Full 30 Charge Injection(3) Q CL = 1nF, VGEN = 0V , RGEN = 0V , Figure 2 25 40 pC Logic Input Input High V oltage VIH Guaranteed Logic High Level Full 1.4 VInput Low V oltage VIL Guaranteed Logic LowLevel Full 0.5 Input High Current IINH VIN = 1.4V , all others = 0.5V Full –1 1 µAInput Low Current IINL VIN = 0.5V , all others = 1.4V Full –1 1

3.0V , SOTiny™ 0.4Ω Single-Supply SPDT Analog Switch

5 PS8712A 07/07/04

Notes: 1. The algebraic convention, where most negative value is a minimum and most positive is a maximum, is used in this data sheet. 2. Typical values are for DESIGN AID ONLY , not guaranteed or subject to production testing. 3. Guaranteed by design. 4. ΔRON = RON max. - RON min. 5. Flatness is defined as the difference between the maximum and minimum value of On-Resistance measured. Electrical Specifications - Single +1.8V Supply (VCC = +1.8V ± 10%, GND = 0V , VIH = 1.4V , VIL = 0.5V) Parameter Symbol Conditions Temp. (°C) Min.(1) Typ.(2) Max.(1) Units Analog Switch Analog Signal Range(3) VANALOG 0 VCC V On-Resistance RON VCC =1.8V , ICOM = –4mA, VNO or VNC = 1.5V 25 0.55 Ω Full 0.65 On-Resistance Match Between Channels(4) ∆RON VCC =1.8V , ICOM = –4mA, VNO or VNC = 0.8V , 1.5V 25 0.1 Full 0.2 On-Resistance Flatness(5) RFLAT(ON) 25 0.9 Full 1.3 Dynamic Turn-On-Time tON VCC =1.8V , VNO or VNC = 1.5V , Figure 1 25 50 nsFull 50 Turn-Off-Time tOFF 25 20 Full 40 Charge Injection(3) Q CL = 1nF, VGEN = 0V , RGEN = 0V , Figure 2 25 36 pC Logic Input Input High V oltage VIH Guaranteed Logic High Level Full 1.4 VInput Low V oltage VIL Guaranteed Logic LowLevel Full 0.5 Input High Current IINH VIN = 1.4V , all others = 0.5V Full –1 1 µAInput Low Current IINL VIN = 0.5V , all others = 1.4V Full –1 1

6 PS8712A 07/07/04

Figure 1. Switching Time Figure 2. Charge Injection Figure 3. Off Isolation Figure 4. Crosstalk

7 PS8712A 07/07/04

Figure 5. Channel-Off Capacitance Figure 6. Channel-On Capacitance

0.65 BSC

3.0V , SOTiny™ 0.4Ω Single-Supply SPDT Analog Switch

8 PS8712A 07/07/04

Packaging Mechanical: 6-Pin SOT-23 (T) 0.102 0.118 BSC 0.60 0.000 0.005 0.00 0.15 0.014 0.019 0.35 0.50 1.50 1.75 0.059 0.068 0.10 0.023 0.004 1.45MAX. SEATING PLANE 0.057 0º - 10º 1.90 0.075 0.037 BSC 2.60 3.00 0.95 0.110 0.118 2.80 3.00 X.XX X.XX Datum "A" DENOTES DIMENSIONS IN MILLIMETERS 6 4 Notes: 1. Thermal characteristics can be found on the company web site at www.pericom.com/packaging/ 2. X = Tape/Reel 3. Number of transistors = TBD

Ordering Information

Ordering Code Package Code Package Description Top Mark PI3A4624TX T 6-pin, Small Compact SOT-23 ZF PI3A4624TEX T Pb-free & Green, 6-pin, Small Compact SOT-23 ZF PI3A4624ZCEX ZC Pb-free & Green, 6-pin, Ultra Compact TDFN ZF Pericom Semiconductor Corporation • 1-800-435-2336 • www.pericom.com