PG880 SJM | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 3
Technical content
Features
- 950 - 2150MHz
- Gain 20.1dB @ 950MHz
- P1dB 20.1dBm @ 1550MHz
- OIP3 39.0dBm @ 1850MHz
- Lead-free / Green / compliant SOT-89 Package ESD/MSL ESD sensitive device. Observe handling precautions.
2 HBM: Class 2, JESD22-A114
3 CDM: Class C3 , JESD22-C101F
4 MSL 3, J-STD-020
2,4 RF OUT / Bias 3 1) Stresses above the maximum values listed have may cause permanent damage to the device. 2) MTTF is more than 100 years. Specifications 1) Test Conditions : T=25°C, Supply Voltage=5V, 75ohm System 2) Note 1. OIP3 measured with two tones at an output power of 5dBm/tone separated by 1MHz. Parameters Units Typ. Condition S21 dB 19.1 950 ~ 2150 MHz S11 dB -15 950 ~ 2150 MHz S22 dB -25 950 ~ 2150 MHz P1dB dBm 19.7 OIP3 dBm 36.0 Note 1 2) NF dB 3.9 V / I V/mA 5 / 83 Rth °C/W 48
Applications
- FTTH Receiver
- Drop Amplifier
- Satellite Amplifier
- Bluetooth / WiFi
http://www.prewell.com 2 Wideband Amplifier SJM PREWELL PG880 Productsand product information are subject to change without notice.Version 0.3 950 1150 1350 1550 1750 1950 2150 25℃ -40℃ 85℃ OIP3 (dBm) Frequency (MHz) OIP3 vs Frequency 950 1150 1350 1550 1750 1950 2150 -45 -30 -15 S11 S22 25℃ -40℃ 85℃ S-Parameter (dB) Frequency (MHz) S21 950 1150 1350 1550 1750 1950 2150 25℃ -40℃ 85℃ P1dB (dBm) Frequency (MHz) P1dB vs Frequency 950 1150 1350 1550 1750 1950 2150 25℃ NF (dB) Frequency (MHz) NF vs. Frequency Parameters Units Frequency (MHz) 950 1250 1550 1850 2150 S11 dB -13 -17 -16 -14 -11 S22 dB -14 -19 -27 -38 -25 Typical RF Performance for Application Circuit Supply Bias Voltage = 5V, Current= 83mA S-Parameter NF vs. Frequency OIP3 vs. Frequency P1dB vs. Frequency RF IN RF OUT33pF 33pF 15nH 10nF 1uF 0.5pF0.5pF
http://www.prewell.com 3 Wideband Amplifier SJM PREWELL PG880 Productsand product information are subject to change without notice.Version 0.3 Lead-free /RoHS Compliant / Green SOT-89 Package Outline Land Pattern Mounting Instructions 1 Use a large ground pad area with many plated through-holes as shown. 2 We recommend 1 ozcopper minimum. 3 Measurement for our data sheet was made on 1.6mm thick FR-4 Board. 4 RF trace width depends on the board material and construction. 5 Add mounting screws near the part to fasten the board to a heatsink. 6 Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance. Evaluation Board Layout (30x40) REF. DIMENSIONS (mm) Min. Max. A 1.40 1.60 B 0.43 0.58 B1 0.36 0.54 C 0.35 0.46 D 4.30 4.70 D1 1.50 1.87 E 2.29 2.70 E1 2.13 2.18 e 1.5 e1 3.0 H 3.43 5.10 L 0.74 1.20 Product Code Lot Number POOOO X X X X