PD15-21B

PD15-21B EVERLIGHT | Alldatasheet

Document overview

• Manufacturer or author: pROVIDED bY alldatasheet.com(free datasheet download site)
• PDF pages: 10

Technical content

Features

․Fast response time ․High photo sensitivity ․Small junction capacitance ․Package in 8mm tape in “7” diameter reel ․Pb free ․The product itself will remain within RoHS compliant version. Descriptions ․PD15-21B/TR8 is a high speed and high sensitive PIN photodiode in miniature flat top view len s SMD package and it is molded in a black plastic. The device is Spectrally matched to infrared emitting diode.

Applications

․High speed photo detector ․Copier ․Game machine Device Selection Guide Chip LED Part No. Material Lens Color PD15-21B/TR8 Silicon Black

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 2 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai PD15-21B/TR8 Package Dimensions Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions ±0.1mm Absolute Maximum Ratings (Ta=25 ℃℃ ℃℃) Parameter Symbol Rating Units Reverse Voltage V R 32 V Operating Temperature T opr -25 ~ +85 ℃ Storage Temperature T stg -40 ~ +100 ℃ Soldering Temperature *1 Tsol 260 ℃ Power Dissipation at(or below) 25 ℃Free Air Temperature Pc 150 mW Notes: *1:Soldering time ≦5 seconds.

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 3 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai PD15-21B/TR8 Electro-Optical Characteristics (Ta=25 ℃℃ ℃℃) Parameter Symbol Condition Min Typ Max Unit Rang Of Spectral Bandwidth λ0.5 --- 730 --- 1100 nm Wavelength Of Peak Sensitivity λP --- --- 940 --- nm Open-Circuit Voltage V OC Ee=5mW /cm 2 Short-Circuit Current I SC Ee=1mW /cm 2 λP=875nm --- 0.8 --- μA Reverse Light Current I L Ee=1mW /cm 2 λP=875nm VR=5V 0.2 0.8 μA Dark Current I D Ee=0mW /cm 2 VR=10V --- --- 10 nA Reverse Breakdown Voltage B VR Ee=0mW /cm 2 IR=100μA 32 170 --- V Total Capacitance C t Ee=0mW /cm 2 f=1MHz VR=5V --- 5 --- pF Rise Time t r --- 6 --- Fall Time t f VR=5V nS

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 4 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai -25 100 150 25 0 50 200 75 85 100 1100 800 700 0.2 0.4 900 1000 1300 Ta=25 0.6 0.8 1.0 C 60 20 40 100 80 100 1000 VR=10V 0.5 0.5 1.0 1.0 2.0 1.5 1.5 3.0 VR=5V PD15-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.1 Power Dissipation vs. Fig .2 Spectral Sensitivity Ambient Temperature Fig.3 Dark Current vs. Fig .4 Reverse Light Current vs. Ambient Temperature Ee

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 5 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai 1 2 10 10 VR=10V Ta=25°C 0.1 100 1 10 t 10 f=1MH Z VR=5V PD15-21B/TR8 Typical Electro-Optical Characteristics Curves Fig.5 Terminal Capacitance vs. Fig .6 Response Time vs. Reverse Voltage Load Resistance

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 6 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai PD15-21B/TR8 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 ℃ or less and 90%RH or less. 2.3 The LEDs should be used within a year.

2.4 After opening the package, the LEDs should be kept at 30

℃ or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 da ys) after opening the package.

2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the

storage time, baking treatment should be performed using the following conditions. Baking treatment : 60 ±5℃ for 24 hours. 3. Soldering Condition

3.1 Lead solder temperature profile

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 7 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai PD15-21B/TR8 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. 4.Soldering Iron Each terminal is to go to the tip of soldering iro n temperature less than 280 ℃ for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs hav e been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 8 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai PD15-21B/TR8 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level ：90% LTPD ：10% NO. Item Test Conditions Test Hours/ Cycles Sample Sizes Failure Judgement Criteria Ac/Re 1 REFLOW Soldering TEMP. ：260 ℃± 5℃ 10secs 6Mins 22pcs 0/1

2 Temperature Cycle H : +100 ℃ 15mins

L : -40 ℃ 15mins 50Cycles 22pcs 0/1

3 Thermal Shock H :+100 ℃ 5mins

L :-10 ℃ 5mins 50Cycles 22pcs 0/1

4 High Temperature

TEMP. ：+100 ℃ 1000hrs 22pcs 0/1

5 Low Temperature

TEMP. ：-40 ℃ 1000hrs 22pcs 0/1

6 DC Operating Life V R=5V 1000hrs 22pcs 0/1

7 High Temperature/

85 ℃ / 85% R.H 1000hrs 22pcs I L≦L×0.8 L ：Lower Specification Limit

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 9 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai Cath o d e A n o d e PD15-21B/TR8 Package Dimensions 1. Reel Dimensions Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm 2. Carrier Tape Dimensions:(Quantity: 2000pcs/reel) Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm

Everlight Electronics Co., Ltd. http:// www.everlight.com Rev 2 Page: 10 of 10 Device No ： DTD-152-139 Prepared date ： 02-15-2008 Prepared by ： Jaine tsai RoHS PD15-21B/TR8 Packing Procedure Aluminum moistue-proof bag Label Desiccant Label Label Form Specification CPN: Customer’s Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s consent. EVERLIGHT ELECTRONICS CO., LTD. Tel: 886-2-2267-2000, 2267-9936 Office: No 25, Lane 76, Sec 3, Chung Yang Rd, F ax: 886-2267-6244, 2267-6189, 2267-6306 Tucheng, Taipei 236, Taiwan, R.O.C http://www.ev erlight.com PD15 -21B/TR8