PD057VU4

PD057VU4 AZDISPLAYS | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 18

Technical content

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:1 FOR MORE INFORMATION: AZ DISPLAYS, INC.

75 COLUMBIA, ALISO VIEJO, CA, 92656

Http://www.AZDISPLAYS.com

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:2 TECHNICAL SPECIFICATION

CONTENTS

NO. ITEM PAGE - Cover 1 - Contents 2

1 Application 3

2 Features 3

3 Mechanical Specifications 3

4 Mechanical Drawing of TFT-LCD module 4

5 Input / Output Terminals 5

6 Absolute Maximum Ratings 6

7 Electrical Characteristics 6

8 Pixel Arrangement 7

9 Display Color and Gray Scale Reference 8

10 Interface Timing 9

11 Power On Sequence 12

12 Optical Characteristics 12

13 Handling Cautions 15

14 Reliability Test 16

15 Packing Diagram 17

• Revision History 18

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:3 1. Application This data sheet applies to a color TFT LCD module, PD057VU4. PD057VU4 module applies to OA product, car TV (must use Analog to Digital driving board), which requires high quality flat panel display. If you must use in severe reliability environment, please don’t extend over PVI’s reliability test conditions. 2. Features . QVGA (320*240 pixels) resolution . Amorphous silicon TFT LCD panel with back-light unit . Pixel in stripe configuration . Thin and light weight . Display Colors：262,144 colors . Optimum Viewing Direction：6 o’clock . TTL interface 3. Mechanical Specifications Parameter Specifications Unit Screen Size 5.7 (diagonal) inch Display Format 320×(R,G,B)×240 dot Display Colors 262,144 Active Area 115.20 (H)×86.4 (V) mm Pixel Pitch 0.36(H)×0.36(V) mm Pixel Configuration Stripe Outline Dimension 144(W)×104.6 (H)×13.0 (D) (typ.) mm Weight 202±10 g Back-light CCFL, 1 tube Surface treatment Anti-glare + wide view film Display mode Normally white

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:4 4.Mechanical Drawing of TFT-LCD Module Outline Drawing : Front View (unit : mm)

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:5 5.Input / Output Terminals 5-1) TFT-LCD Panel Driving Connector type: ELCO 08-6210-033-340-800A+ , PIN No 33 pins, pitch=0.5mm Pin No Symbol I/O Description Remark

1 GND - GND

2 CK I Clock signal for sampling each data signal

3 Hsync I Horizontal synchronous signal(neqative)

4 Vsync I Vertical synchronous signal(neqative)

5 GND - GND

6 R0 RED data signal(LSB)

7 R1 I RED data signal

8 R2 I RED data signal

9 R3 I RED data signal

10 R4 I RED data signal

11 R5 I RED data signal(MSB)

12 GND - GND

13 G0 I GREEN data signal(LSB)

14 G1 I GREEN data signal

15 G2 I GREEN data signal

16 G3 I GREEN data signal

17 G4 I GREEN data signal

18 G5 I GREEN data signal(MSB)

19 GND - GND

20 B0 I Blue data signal(LSB)

21 B1 I Blue data signal

22 B2 I Blue data signal

23 B3 I Blue data signal

24 B4 I Blue data signal

25 B5 I Blue data signal(MSB)

26 GND - GND

27 ENAB I Signal to settle the horizontal display position(positive) Note5-1

28 VCC - +3.3V power supply 29 VCC - +3.3V power supply

30 R/L I Horizontal display mode select signal

L：Normal ,H：Left /Right reverse mode Note5-2

31 U/D I Vertical display mode select signal

H：Normal ,L :Up/Down reverse mode Note5-3

32 V/Q I VGA / QVGA mode select signal

33 GND - GND

Note5-1：The horizontal display start timing is settled in accordance with rising of ENAB signal. In case ENAB is fixed ”Low”,the horizontal start timing is determined as described in 10-2. Don\`t keep ENAB”High” during operation.

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:6 Note 5-2 , 5-3 : The definitions of U/D & R/L R/L(PIN 30)= Low, U/D(PIN 31)= High R/L(PIN 30)= High , U/D(PIN 31)= Low 5-2) Backlight driving Connector type: JST BHR-03VS-1, PIN No 2 pins, pitch=3.5mm Pin No Symbol Description Remark

1 V Low Power supply for lamp (Low voltage side) White

• NC This is electrically opened -

2 V High Power supply for lamp (High voltage side) Red

Note 5-11: Low voltage side of backlight inverter connects with ground of inverter circuits. 6.Absolute Maximum Ratings: GND=0V, Ta=25℃ Parameters Symbol Condition MAX. Unit Remark Input Voltage VI Ta=25℃ -0.3~+4 V Note6-1 +3.3V supply voltage V CC Ta=25℃ 0~+3.6 V Note6-1:CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,R/L,U/D,V/Q 7.Electrical Characteristics 7-1) Recommended Operating Conditions: G N D = 0 V , T a = 2 5 ℃ Item Symbol Min. Typ. Max. Unit Remark +3.3V Supply Voltage V CC +3.0 +3.3 +3.6 V Permissive input ripple voltage V RF - - 100 mVp-p V CC=3.3V Input voltage(Low) V IL 0 - 0.3 VCC V Input voltage(High) V IH 0.7 V CC - VCC V

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:7 7-2) Recommended Driving Condition for Back Light T a = 2 5 ℃ Parameter Symbol Min. Typ. Max. Unit Remark Lamp Voltage V L 639 710 781 V I L=5mA Lamp Current I L 4 5 8 mA Note 7-1 Lamp Frequency P L - 35 - KHz Note 7-2 Starting Voltage (25℃) (Reference Value) Vs - - 1240 Vrms Note 7-3 Starting Voltage (0℃) (Reference Value) Vs - - 1380 Vrms Note 7-3 Note 7-1：In order to have proper operation of the B/L, no matter what kind of inverters, the output lamp current must be between Min. and Max. values to avoid the abnormal display image caused by B/L. Note 7-2：The driving frequency of the lamp may interfere with the horizontal synch signal, leaving interference stripes on the display. So please evaluate LCD panels beforehand. To avoid interference stripes, we recommend to separate as far as possible the lamp frequency from the horizontal synchronous signal and its high harmonic frequency. The inverter which PVI uses is TAD347-1. Note 7-3：The “Starting Voltage” means the minimum voltage of inverter to turn on the lamp. And it should be applied to the lamp for more than 1 second to start up. Otherwise the lamp may not be turned on 7-3) Power Consumption Parameters Symbol Typ. Max. Unit Remark +3.3V Current Dissipation I CC 67 75 mA LCD Panel Power Consumption - 0.22 0.25 W Note 7-4 Backlight Power Consumption - 3.55 3.91 W Note 7-5 Note 7-4: The power consumption for back light is not included. Note 7-5: Back light lamp power consumption is calculated by IL×VL. 8. Pixel Arrangement The LCD module pixel arrangement is stripe configuration. R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B rd Line 2 nd Line st Line 240 th Line 239 thLine 238 th Line R G B R G B R G B R G B 1 st Pixel 320th pixel

1 Pixel = R G B

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:8 9. Display Color and Gray Scale Reference Input Color Data Color Red Green Blue R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 B l a c k 0 0 000000000000 0 0 0 0 Red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Basic Blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 Colors Cyan 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 Magenta 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 Y e l l o w 1 1 111111111100 0 0 0 0 W h i t e 1 1 111111111111 1 1 1 1 Red (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (01) 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Red (02) 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 D a r k e r Brighter Red (61) 1 1 1 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 Red (62) 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 Red (63) 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 Green (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Green (01) 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 Green (02) 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 D a r k e r Brighter Green (61) 0 0 0 0 0 0 1 1 1 1 0 1 0 0 0 0 0 0 Green (62) 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 Green (63) 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 Blue (00) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Blue (01) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Blue (02) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 D a r k e r Brighter Blue (61) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 0 1 Blue (62) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 Blue (63) 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:9 10. Interface Timing 10-1) Timing Parameters Characteristics Symbol Min. Typ. Max. Unit Remark - 25.18 28.33 MHz V/Q=H Frequency 1/Tc - 6.3 7.0 MHz V/Q=L Clock Duty ratio Tch/Tc 40 50 60 % V/Q=L Set up time Tds 5 - - Data Hold time Tdh 10 - - ns 30.0 31.8 - us TH 700 800 900 clock V/Q=H 50.0 63.6 - us Cycle TH 360 400 450 clock V/Q=L Horizontal sync. signal Pulse width THp 2 96 200 clock TV 515 525 560 V/Q=H Cycle TV 251 262 280 line V/Q=L Vertical sync. signal Pulse width TVp 2 - 34 line Horizontal display period THd 320 Clock Hsync.-Clock phase difference THc 10 - Tc-10 ns Hsync.-Vsync. phase difference TVh 0 - TH-THp ns 34 V/Q=H Vertical sync. signal start position TVs 7 line V/Q=L Note10-1：In case of lower frequency, the deteriorati on of the display qua lity, flicker etc., may occur. Parameter symbol Min. Typ Max Unit Remark Set up time Tes 5 - Tc-10 ns Enable signal Pulse width Tep 2 320 TH-10 clock 44 - TH-664 V/Q=H Hsync-Enable signal phase difference The 2 - TH-340 clock V/Q=L Note10-2： When ENAB is fixed at “V/Q=Low”, the display starts from the data of C52 (clock). When ENAB is fixed at “V/Q=High”, the display starts from the data of C104 (clock).

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:10 10-2) Timing Diagram 〜 〜

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:11 TV 0.3VDD Vertical sync.Signal(Vsync) Data signal(R0~R5,G0~G5, B0~B5) Verticla invalid data period 0.7VDD TVp 0.3VDD TVh 0.7VDD Horizontal sync.Signal(Hsync) 1line 2line Nline DH1 DH2 DH240 Verticla invalid data period TVs TVd *2 The vertical display position (TVs) is fixed at 34th line (V/Q=H) and 7th line (V/Q=L).

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:12 11. Power On Sequence VDD 3.0V 0.3V 3.0V t1 t2 t3 Signal*3 1. 0 ＜t1≦20ms 2. 0 ＜t2≦50ms 3. 0 ＜t3≦1s 12. Optical Characteristics 12-1) Specification: Ta=25℃ Parameter Symbol Condition MIN. TYP. MAX. Unit Remarks Horizontal θ 55 60 - deg Note 12-1 θ(to 6 o’clock) 45 50 - deg Viewing Angle Vertical θ(to 12 o’clock) CR≧10 35 40 - deg Contrast Ratio CR At optimized viewing angle 200 400 - - Note 12-2 Rise Tr - 15 30 ms Response time Fall Tf θ=0° - 25 50 ms Note 12-3 Brightness - θ=0°/φ=0 450 500 - cd/㎡ Note 12-4 Luminance Uniformity U% 75 80 - % Note 12-5 x 0.29 0.32 0.35 - White Chromaticity y 0.33 0.36 0.39 - Lamp Life Time - - 50000 - hr At=5mA

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:13 Note 12-1: The definitions of viewing angles are as follow 12 o’clock 3o’clock 9o’clock 6o ’clock θ φ Lamp connector Note 12-2: The definition of contrast ratio CR Luminance at gray level 63 Luminance at gray level 0= Note 12-3: Definition of Response Time T r and Tf: 100% 90% 10% White White Brightness Black Tr Tf

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:14 Note 12-4: All optical measurements shall be performed after backlight being turned-on for 30 mins. The optical characteristics shall be measured in dark room (ambient illumination on panel surface less than 1 Lux). The measuring configuration shows as following figure. Note 12-5: The uniformity of LCD is defined as The Minimum Brightness of the 9 testing Points U = The Maximum Brightness of the 9 testing Points Luminance meter: BM-5A or BM-7 fast (TOPCON) Measurement distance: 500 mm +/- 50 mm Ambient illumination: < 1 Lux Measuring direction: Perpendicular to the surface of module The test pattern is white (Gray Level 63). 1/6 1/6 2/6 2/6 Photometer (TOPCON BM-5A or BM-7 fast) 500 mm +/- 50 mm TFT-LCD module DC/AC Inverter Optical characteristics measuring configuration Field = 1°

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:15 13. Handling Cautions 13-1) Mounting of module a) Please power off the module when you connect the input/output connector. b) Please connect the ground pattern of the inverter circuit surely. If the connection is not perfect, some following problems may happen possibly. 1. The noise from the backlight unit will increase. 2. The output from inverter circuit will be unstable. 3. In some cases a part of module will heat. c) Polarizer which is made of soft material and susceptible to flaw must be handled carefully. d) Protective film (Laminator) is applied on surface to protect it against scratches and dirts. It is recommended to peel off the laminator before use and taking c a r e o f s t a t i c e l e c t r i c i t y . 13-2) Precautions in mounting a) When metal part of the TFT-LCD module (shielding lid and rear case) is soiled, wipe it with soft dry cloth. b) Wipe off water drops or finger grease immediately. Long contact with water may cause discoloration or spots. c) TFT-LCD module uses glass which breaks or cracks easily if dropped or bumped on hard surface. Please handle with care. d) Since CMOS LSI is used in the module. So take care of static electricity and earth yourself when handling. 13-3) Adjusting module a) Adjusting volumes on the rear face of the module have been set optimally before shipment. b) Therefore, do not change any adjusted values. If adjusted values are changed, the specifications described may not be satisfied. 13-4) Others a) Do not expose the module to direct sunlight or intensive ultraviolet rays for many hours. b) Store the module at a room temperature place. c) The voltage of beginning electric discharge may over the normal voltage because of leakage current from approach conductor by to draw lump read lead line around. d) If LCD panel breaks, it is possibly that the liquid crystal escapes from the panel. Avoid putting it into eyes or mouth. When liquid crystal sticks on hands, clothes or feet. Wash it out immediately with soap. e) Observe all other precautionary requirements in handling general electronic components. f) Please adjust the voltage of common electrode as material of attachment by 1 module. 13-5) Polarizer mark The polarizer mark is to describe the direction of wide view angle film how to match up with the rubbing direction.

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:16 14. Reliability Test No Test Item Test Condition Remark

1 High Temperature Storage Test Ta = +80℃, 240 hrs

2 Low Temperature Storage Test Ta = -30℃, 240 hrs

3 High Temperature Operation Test Ta = +70℃, 240 hrs

4 Low Temperature Operation Test Ta = -20℃, 240 hrs

High Temperature & High Humidity Operation Test Ta = +60℃, 90%RH, 240 hrs (No Condensation) Thermal Cycling Test (non-operating) -20℃Æ+70℃, 200 Cycles 30 min 30 min Vibration Test (non-operating) Frequency: 10 ~ 57 HZ /Vibration Width:0.075mm 58-500 Hz / Gravity: 9.8m/s2 Sweep time: 11 minutes Test period: 3 hrs for each direction of X, Y, Z Shock Test (non-operating) Gravity: 490m/s2 * 6ms Direction: ±X, ±Y, ±Z Pulse Width: 11ms, half sine wave

9 Electrostatic Discharge Test

(non-operating) Machine Mode = ±200V C = 200pF , R = 0Ω 1 times discharge for each pad Ta: ambient temperature Note: The protective film must be removed before temperature test [Criteria] 1. Main LCD should normally work under the normally condition no defect of function, screen quality and appearance (including : Mura ,line defect ,no image) 2. After the temperature and humidity test, the luminance and CR (Contrast ratio), should not be lower than minimum of specification. 3. After the vibration and shock test, can’t be found chip broken.

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:17 15. Packing Diagram

The information contained herein is the exclusive property of Prime View In ternational Co., Ltd. and shall not be distributed, reproduced, or discl osed in whole or in part without prior writt en permission of Prime View International Co., Ltd. Page:18

Revision History

Rev. Issued Date Revised Contents 1.0 Jul.11, 2006 preliminary