ATM1040D3_13 AZDISPLAYS | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 19
Technical content
Datasheet sections
- 0 Record of Revision
- 1 Summary
- 2 Features
- 3 General Specifications
- 4 Absolute Maximum Rating
- 5 Electrical Characteristics
- 6 DC Characteristics
- 7 AC Characteristics 7-9
- 8 Optical Characteristics 10-12
- 9 Interface Pin Connection 13-14
- 10 Block Diagram
- 11 Quality Assurance
- 12 Outline Drawing
- 13 Package Form
- 14 Precautions 18-19
※※※※PART NO .: AT M 1040D3 (A Z DISPLAYS) VER1.0 APPRO VAL CO M PANY CH O P CUSTO M ER CO M M ENTS AZ DISPLAYS ENG INEER ING APPRO VAL DESIG NED BY CH ECK ED BY APPRO VED BY
Version Revise Date Page Content V1.0 2010-05-13 First issued ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Summary ATM1040D3 is a transmissive type color active matrix liquid crystal display (LCD), which uses amorphous thin film transistor (TFT) as switching devices. This panel has a 10.4 inches diagonally measured active display area with SVGA (800 RGB x 600) resolution. The following describes the features of this product. 2. Features 10.4” (diagonal) inch configuration SVGA (800 600 pixels) resolution 3. General Specifications No. Item Specification Unit 1 Screen Size 10.4 (Diagonal) inch
2 Display Resolution 800 RGB x 600 pixel
3 Dot Pitch 0.088 (H) x 0.264 (V) mm 4 Pixel Pitch 0.264 (H) x0.264 (V) mm 5 Active Area 211.2(H) x 158.4(V) mm 6 Outline Dimension 228.4 (H) x 175.4 (V) x 5.9 (D) mm
7 Pixel Configuration RGB-Stripe --
8 Color Depth 16.2M colors
9 LCD Type TM TN --
10 Interface Type Digital 24bit RGB --
11 Surface Treatment 3H --
12 View direction (Gray inversion) 6 o’clock --
13 Weight 390 g
- Absolute Maximum Rating (Ta = 25 ± 2 ) Note: (1) All of the voltages listed above are with respective to GND= 0V (2) Device is subject to be damaged permanently if stresses beyond those absolute maximum ratings listed above. Values Item Symbol Min. Max. Unit Note Storage Temperature TST -30 80 Operation Temperature TOP -20 70 Digital Supply Voltage VCC -0.3 5 V (2) Analog Power Supply Voltage AVDD -0.5 15 V (3) TFT Device on voltage VGH -0.3 42 V (4) TFT Device off voltage VGL VGH - 42 0.3 V (4) ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Electrical Characteristics 5-1. Operating Conditions: (Ta = 25 ± 2 ) 5-2. Backlight Driving Conditions: (Ta = 25 ± 2 ) Note: (1) Brightess to be decreased to 50% of the initial value Values Item Symbol Min. Typ. Max. Unit Note Digital Power Supply Voltage VCC 3.0 3.3 3.6 V Digital Supply Current ICC 24 30 45 mA Black Pattern Analog Power Supply Voltage AVDD 11.5 12 12.5 V Analog Supply Current IAVDD 32 40 60 mA Black Pattern TFT Device on voltage VGH - (18) - V TFT Device off voltage VGL - (-7) - V Common Electrode Driving Voltage VCOM - 5.3 - V LED Reverse Voltage Vr 1.5 V For single LED LED Forward Current If 20 30 mA For single LED Values Item Symbol Min. Typ. Max. Unit Note Power Consumption PBL -- 2.304 2.52 W -- LED Current IF -- 240 -- mA -- Backlight Voltage VBL -- 9.6 10.5 V -- Life Time -- 10000 -- -- hrs (1) ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- DC Characteristics
6.1 Parameter
(Ta = 25 ± 2 ) Note: (1) For Digital Circuit
6.2 Power Sequence
The LCD panel power ON/OFF sequence is as below Min. Typ. Max. Unit T1 - - 20 ms T2 16 - - ms T3 > 0 ms T4 >0 ms T5 >0 ms T6 >0 ms Values Item Symbol Min. Typ. Max. Unit Note Low Level Input Voltage VIL 0 - 0.3VCC V (1) High Level Input Voltage VIH 0.7 VCC - VCC V (1) ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- AC Characteristics 7.1. Data Timing (Under frame rate is equal to 60Hz) Horizontal Timing Spec Parameter Symbol Min. Typ. Max. Unit Horizontal Display Area thd 800 CLK CLK Frequency fclk - 40 50 MHz One Horizontal Line th 862 1056 1200 CLK HS Pulse Width thpw 1 - 40 CLK HS Back Porch thb 46 CLK HS Front Porch thfp 16 210 354 CLK Vertical Timing Spec Parameter Symbol Min. Typ. Max. Unit Vertical Display Area tvd 600 th VS Period Time tv 624 635 700 th VS Pulse Width tvpw 1 - 20 th VS Back Porch tvb 23 23 23 th VS Front Porch tvfp 1 12 77 th Note: CMO suggest using frame rate 60Hz to have better performance Horizontal Timing ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
7.2. AC Electrical characteristic Spec. Parameter Symbol Min. Typ. Max. Unit HS setup time Thst 8 - - ns HS hold time Thhd 8 - - ns VS setup time Tvst 8 - - ns VS hold time Tvhd 8 - - ns Data setup time Tdsu 8 - - ns Data hold time Tdhd 8 - - ns DE setup time Tesu 8 - - ns DE hold time Tehd 8 - - ns VDD Power On Slew Rate TPOR - - 20 ms RSTB pulse width TRst 10 - - us CLKIN cycle time Tcph 20 - - ns CLKIN pulse duty Tcwh 40 50 60 % Output stable time Tsst - - 6 ns Repair OPA Output Stable time TRsst - - 6 ns ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
7.3. Input Clock and Data Timing Waveform ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Optical Characteristics (Ta = 25 ± 2, IF=20mA) Note: (1) Definition of viewing angle range Specifications Item Symbol Conditions Min. Typ. Max. Unit Note Contrast Ratio CR 300 500 -- -- (2),(4), (6) Brightness B 200 250 -- cd/m2 Tr -- 5 10 ms Response time Tf -- 15 20 ms (3) Wx 0.26 0.31 0.36 -- Chromaticity White Wy Viewing normal angle = 0° = 0° B/L On 0.28 0.33 0.38 -- (2)(5)(6) L 60 70 - Hor. R 60 70 - T 40 50 - Viewing Angle Ver. B CR 10 B/L On 50 60 - deg. (1) Uniformity -- -- -- 80 -- % (7) ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
Fig. 8-1 Definition of viewing angle (2) Test equipment setup: After stabilizing and leaving the panel alone at a driven temperature for 10 minutes, the measurement should be executed. Measurement should be executed in a stable, windless, and dark room. Optical specifications are measured by Topcon BM-7 luminance meter 1.0° field of view at a distance of 50cm and normal direction. Fig. 8-2 Optical measurement system setup (3) Definition of Response time: The response time is defined as the LCD optical switching time interval between “White” state and“Black” state. Rise time, Tr, is the time between photo detector output intensity changed from 90to 10. And fall time, Tf, is the time between photo detector output intensity changed from10to 90. ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
(4) Definition of contrast ratio: The contrast ratio is defined as the following expression. Luminance measured when LCD on the “White” state Contrast ratio (CR)= Luminance measured when LCD on the “Black” state (5) Definition of color chromaticity (CIE 1931) Color coordinates measured at the center point of LCD (6) Measured at the center area of the panel when all the input terminals of LCD panel are electrically opened. Brightness (min) (7) Uniformity (U) = x 100% Brightness (max) ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Interface Pin Connection Pin Symbol I/O Function Remark
1 GND G Power Ground
2 AVDD P Analog input voltage
3 VCC P Digital input voltage
4 R0 I Red data input (LSB)
5 R1 I Red data input
6 R2 I Red data input
7 R3 I Red data input
8 R4 I Red data input
9 R5 I Red data input
10 R6 I Red data input
11 R7 I Red data input (MSB)
12 G0 I Green data input (LSB)
13 G1 I Green data input
14 G2 I Green data input
15 G3 I Green data input
16 G4 I Green data input
17 G5 I Green data input
18 G6 I Green data input
19 G7 I Green data input (MSB)
20 B0 I Blue data input (LSB)
21 B1 I Blue data input
22 B2 I Blue data input
23 B3 I Blue data input
24 B4 I Blue data input
25 B5 I Blue data input
26 B6 I Blue data input
27 B7 I Blue data input (MSB)
28 CLKIN I Dot clock input
29 DEN I Data enable signal
30 HSD I HSYNC signal
31 VSD I VSYNC signal
32 MODE I H: DE mode (Default)
L: SYNC mode ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
33 NC I No connect (please leave it open)
34 NC I No connect (please leave it open)
35 NC - No connect (please leave it open)
36 VCC P Digital input voltage
37 NC - No connect (please leave it open)
38 GND G Power Ground
39 GND G Power Ground
40 AVDD P Analog input voltage
41 VCOM P VCOM DC input
42 DITH I
Dithering function setting H: Disable dithering function L: Enable dithering function
43 NC - No connect (please leave it open)
44 VCOM out O connect a capacitor
45 NC No connect (please leave it open)
46 NC No connect (please leave it open)
47 NC No connect (please leave it open)
48 NC No connect (please leave it open)
49 NC No connect (please leave it open)
50 NC No connect (please leave it open)
51 NC No connect (please leave it open)
52 NC No connect (please leave it open)
53 NC No connect (please leave it open)
54 NC No connect (please leave it open)
55 NC - No connect (please leave it open)
56 VGH P TFT turn on voltage
57 VCC P Digital input voltage
58 VGL P TFT turn off voltage
59 GND G Power Ground
60 NC - No connect (please leave it open)
Note: (1) Suggested connector: MT-FP160N-2FR (UJU)or any equivalent ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Block Diagram 11. Quality Assurance No. Test Items Test Condition Note
1 High Temperature Storage Test Ta=70 Dry 240h
2 Low Temperature Storage Test Ta=-20 Dry 240h
3 High Temperature Operation Test Ta=60 Dry 240h
4 Low Temperature Operation Test Ta=-10 Dry 240h
5 High Temperature and High Humidity
Operation Test Ta=50 80%RH 240h
6 Electro Static Discharge Test
Contact / Air±6KV / ±15KV 150pF330 Non-operating
7 Shock Test (non-operating)
Shock Level : 100G Waveform: Half Sinusoidal wave Shock Time : 6ms
3 Axis for all six faces/ each
8 Vibration Test (non-operating)
0.015 G2/Hz from 5-200Hz
-6dB/ octave from 200-500Hz 9 Thermal Shock Test -10(0.5Hr) ~ +60(0.5Hr) for 100 cycles Note: (1) All the cosmetic specifications are judged before the reliability stress.
800 RGB x 600
R, G, B 1st ~ 60th ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Outline Drawing ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS 15
- Package Form ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
- Precautions Please pay attention to the following when you use this TFT-LCD module.
14.1 Mounting Precautions
(1) You must mount a module using arranged in four corners or four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module. (3) Please attach a transparent protective plate to the surface in order to protect the polarizer. Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not describe because the former generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction. (6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HB pencil lead. And please do not rub with dust clothes with chemical treatment. Do not touch the surface of polarizer for bare hand or greasy cloth. (Some cosmetics are determined to the polarizer) (7) When the surface becomes dusty, please wipe gently with adsorbent cotton or other soft materials like chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer. (8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes deformations and color fading. (9) Do not open the case because inside circuits do not have sufficient strength.
14.2 Operating Precautions
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage V=±200mV(Over and under shoot voltage) (2) Response time depends on the temperature. (In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower) And in lower temperature, response time (required time that brightness is stable after turned on) becomes longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or electrical contacted parts. And after fading condensation, smear or spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS
shall be done by system manufacturers. Grounding and shielding methods may be important to minimize the interference.
14.3 Electrostatic Discharge Control
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wristband etc. And don’t touch interface pin directly.
14.4 Precautions for Strong Light Exposure
Strong light exposure causes degradation of polarizer and color filter.
14.5 Storage
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature between 5 and 35 at normal humidity . (2) The polarizer surface should not come in contact with any other object. It is recommended that they be stored in the container in which they were shipped.
14.6 Handling Precautions for Protection Film
(1) When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion-blown equipment or in such a condition, etc. (2) The protection film is attached to the polarizer with a small amount of glue. Is apt to remain on the polarizer. Please carefully peel off the protection film without rubbing it against the polarizer. (3) When the module with protection film attached is stored for a long time, sometimes there remains a very small amount of glue still on the polarizer after the protection film is peeled off. (4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige is recognized, please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane. ATM1040D3(AZ DISPLAYS) TFT MODULE VER1.0 AZ DISPLAYS