PBM300 XPPOWER | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
300 Watts
- Worldwide Medical Approvals
- Single, Dual, Triple and Quad Outputs
- Power Fail Detect
- Remote On/Off
- U Channel and Enclosed Versions
- 150 Watt Convection-cooled Rating
- 3 Year Warranty PBM300 Series Input Input Voltage • 90-264 VAC Input Frequency • 47-63 Hz Input Current • 4.7 A rms at 115 VAC,
2.3 A rms for 230 VAC
Inrush Current • 30 A at 115 VAC,
60 A at 230 VAC cold start +25 °C
Power Factor • 0.98 typical Earth Leakage Current• 100 µA max at 115 VAC/60 Hz 220 µA max at 230 VAC/50 Hz Input Protection • Internal F6.3 A/250 V in line and neutral lines Output Output Voltage • See table Output Voltage Trim • ±5% for outputs 1 & 2 Initial Set Accuracy• ±2% Minimum Load • See table and note 5 Start Up Delay • 2 s max Start Up Rise Time • 18 ms typical Hold Up Time • 12 ms min at full load and 110 VAC Drift • ±0.2% Line Regulation • ±0.2% max Load Regulation • See note 6 Transient Response • 4% max deviation, recovery to within 1% in 500 µs for a 25% load change Ripple & Noise • 2% max pk-pk, 20 MHz bandwidth, with a 22 µF electrolytic & a 0.47 µF tantalum capacitor Overvoltage Protection• 115-140% Vnom output 1 only, recycle input to reset Overtemperature • Shutdown at +95 °C (singles) or +105 °C Protection (multi-outputs) with auto recovery, measured internally Overload Protection • 110-150% typical, auto recovery Short Circuit Protection• Trip and restart (Hiccup mode) Temperature • 0.04%/°C Coefficient Remote Sense • Compensates for up to 0.5 V drop Remote On/Off • On = Logic low or open circuit Off = Logic high xppower.com General Efficiency • 80% maximum Isolation • 4000 VAC Input to Output
1500 VAC Input to Ground
500 VAC Output to Ground
Switching Frequency • 70 kHz ±10 kHz Signals • Power fail detect, remote on/off Power Density • 5.08 W/In3 Power Fail Detect • AC OK = TTL logic high AC not OK = TTL logic low MTBF • 300 kHrs to MIL-HDBK-217F at +25 °C, GB Environmental Operating Temperature• 0 °C to +70 °C, derate linearly from 100% power at +50 °C to 50% power at +70 °C Cooling • ‘C’ versions have internal fan, ‘B’ versions are derated with convection cooling or require 35 CFM (see note 4) Operating Humidity • up to 95% RH, non-condensing Storage Temperature • -40 °C to +85 °C Operating Altitude • 2500 m Shock • Half sine pulse. acceleration 50 g, 11 ms duration, 3 shocks in each direction, unpackaged, non-operating Vibration • Sinusoidal 10-50 Hz, amplitude 0.15 mm, 30 min/axis, unpackaged, non-operating EMC & Safety Emissions • EN55011 and FCC Class B conducted & radiated Harmonic Currents • EN61000-3-2, Class A Voltage Flicker • EN61000-3-3 ESD Immunity • EN61000-4-2, level 3 Perf Criteria A Radiated Immunity • EN61000-4-3, level 3 Perf Criteria A EFT/Burst • EN61000-4-4, level 3 Perf Criteria A Surge • EN61000-4-5, level 3 Perf Criteria A Conducted Immunity • EN61000-4-6, 3 V Perf Criteria A Dips & Interruptions• EN61000-4-11, 30% 10 ms, 60% 100 ms, >95% 5000 ms, Perf Criteria A, A, B Safety Approvals • EN60601-1, UL60601-1, CSA22.2 No. 601-1 per cUL Specification
- For U-bracket format replace suffix ‘ -C’ with suffix ‘ -B’ . 2. All auxiliary outputs are floating and can be connected externally for either positive or negative output. 3. Output 1 & 2 can be adjusted within ±5% of their nominal voltage. 4. 300 W for ‘ C’ version with cover and fan assembly. 150 watts for ‘ B’ version with convection cooling (maximum current of output 1 & 2 derated by 50%). 300 W for ‘ B’ version with 35 CFM forced air provided by user. PBM300PS03 is rated 200 W with 35 CFM forced air cooling or 100 W convection-cooled. PBM300PQ01 is rated 250 W with 35 CFM forced air cooling or 125 W with convection cooling. 5. Zero minimum load for outputs 3 & 4. 10% minimum load required on out- put 1 for all outputs to meet regulation. 6. Total regulation includes initial tolerance, line regulation and load regulation. PCB B A B A 5.70 (144.8) 0.95 (24.1) B A L N G 1 P1 B A 1.34 (34.2) 0.94 (24.0) Voltage adj., multi Voltage adj., single 1.80 (45.7) 2.60 (66.0) 4.50 (114.3) 1.00 (25.4) 0.63 (16.0) 1.75 (44.45) B AA B 1.00 (25.4) 7.00 (177.8) 7.50 (190.5) 1.75 (44.45) B A B A FAN Multi Output Models Single Output Models Notes 2. Mounting Holes A: #6-32 Mounting Screw, B: M3 x 0.5, Maximum mounting screw length from surface of chassis is 0.14 inch (3.5 mm) 3. Input connector P1 is Dinkle P/N DT-35-B01W-03. Screws are M3 x 0.5 on 0.375” centres. 4. Connector P4 mates with Molex housing 50-37-5103 & pins 5263. 5. Connectors P2. P3, P5 & P6: M3x0.5 screw connections. 6. Connector P7 mates with Molex housing 09-50-3041 & 2878 series crimp terminals. 7. DC fan on P4 is rated at 12 V/0.1 A. Conn Pin Model Number(s) PSXX PQXX
1 Line Line
2 Neutral Neutral
3 Ground Ground
1 Signal Ground Signal Ground
4 PFD PFD
5 Remote On/Off Remote On/Off
6 N.C. N.C. 7 N.C. +sense OP2 8 N.C. -sense OP2 9 0V (fan) 0V (fan) 10 12V (fan) 12V (fan) P5 1 OP1 Return OP2 P6 1 OP1 Return OP2 Return 1 n/a OP3 2 n/a OP3 Return 3 n/a OP4 4 n/a OP4 Return Mechanical Details Output Power (4) Output 1 Output 2(2) Output 3(2) Output 4(2) Model Number (1) Vnom (3) Imin(5) Imax Reg (6) Vnom (3) Imin Imax Reg (6) Vnom Imax Reg (6) Vnom Imax Reg (6) 200 W 3.3 V 3.0 A 60.0 A 3% PBM300PS03-C 300 W 5.1 V 3.0 A 60.0 A 2% PBM300PS05-C 300 W 12.0 V 1.2 A 25.0 A 2% PBM300PS12-C 300 W 15.0 V 1.0 A 20.0 A 2% PBM300PS15-C 300 W 24.0 V 0.6 A 12.5 A 2% PBM300PS24-C 300 W 30.0 V 0.5 A 10.0 A 2% PBM300PS30-C 300 W 48.0 V 0.5 A 6.3 A 2% PBM300PS48-C