PAN9026

PAN9026 PANASONIC | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 99

Technical content

PAN9026 Wi-Fi Dual Band 2.4 GHz and 5 GHz and Bluetooth Module Product Specification Rev. 1.2 Wireless Modules 

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 2 Chip Antenna SPDT 88W8977 Radio SoC Crystal 32.768 kHz SPI UART COEX GPIOs Status LED's MCU Ready PDN Factory Reset V SPDT Wake Up's JTAG VIO 1.8 V BPF RF Pad PAN9026 Wi-Fi & Bluetooth Radio Module IEEE 802.11 a/b/g/n Bluetooth 5.0 (BR, LE & EDR) Crystal

26 MHz

50 Ohm

VDD 2.2 V VDD 1.8 V PCM Interface SDIO Interface VIO SD 32 kHz DISABLE RF SWVIO RF 3.3 VCNTL Overview The PAN9026 is a 2.4 GHz and 5 GHz ISM band Wi-Fi and Bluetooth radio module, which includes a wireless radio for easy integration of Wi-Fi and Bluetooth connectivity into various electronic devices.

Features

• Dual band 2.4 GHz and 5 GHz 802.11 a/b/g/n Wi-Fi/Bluetooth combined module
• Supports 802.11i security standards through AES, CCMP, and more security mechanisms
• 802.11e Quality of Service is supported for multimedia applications
• IEEE 802.11n-compliant, 1x1 spatial stream with data rates up to MCS7 150 Mbps
• Bluetooth 5.0, includes Low Energy (LE)
• Dual simultaneous and independent WLAN and Bluetooth operation
• Dynamic Rapid Channel Switching (DRCS) for simultaneous operation in 2.4 GHz and 5 GHz bands
• Indoor location and navigation with IEEE 802.11mc
• Power management with sleep clock
• Coexistence interface for arbitration of colocated WLAN, Bluetooth, or Mobile Wireless System (e.g. LTE)
• Generic interfaces include SDIO 3.0 and high-speed UART for host processor connection
• Software Linux driver Characteristics
• Surface Mount Type (SMT) 17.5 mm x 10.0 mm x 2.6 mm
• Marvell® 88W8977 WLAN 2.4 GHz and 5 GHz and Bluetooth single-chip solution inside
• TX Power 16 dBm @ 802.11b
• RX Sensitivity -98 dBm @ 802.11b DSSS

1 Mbps

• IEEE 802.11n 20 MHz and 40 MHz channel bandwidth
• Long and Short Guard Interval support
• Power supply 3.3 V, 2.2 V, 1.8 V
• Current consumption Wi-Fi typical 400 mA @ TX and 70 mA @ RX
• SDIO 1-bit or 4-bit
• Wide temperature range of -30 °C to 85 °C Block Diagram

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 3 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2019. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Description does not lodge the claim to be complete and free of mistakes. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by:  The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer,  Deviation or lapse in function of the Engineering Sample,  Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 4 Table of Contents

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 5

 PAN9026 Wi-Fi/Bluetooth Module

1 About This Document

Product Specification Rev. 1.2 Page 6

1.1 Purpose and Audience

This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN9026 modules. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN9026” or “the module” within this document.

1.2 Revision History

Revision Date Modifications/Remarks 1.0 2017-12-20 Changed to Bluetooth 5.0. Changed PM in chapter “Power Configuration Example with 3.3 V Host Operation“. Included values in chapter “Current Consumption“ and chapter ”RF Characteristics“. Removed chapter “TDM Interface”. Additional models in chapter “Ordering Information”. Added section in chapter “Acronyms and Abbreviations“. 1.1 2018-07-03 Renamed section in chapter “Restricted Use“. Moved section in chapter “Life Support Policy”. Added section in chapter “Restricted End Use“. Added additional models “Ordering Information“. 1.2 2019-06-24 Changed Block Diagram in chapter “Power Configuration Example with 3.3 V Host Operation“. Added Table in chapter “Channel Tables based on Regulatory Domain/Country“. Changed Storage Temperature in chapter “Absolute Maximum Ratings“. Changed Power-Up in chapter “Power-up Sequence“. Restructure and update chapter “Cautions“. Added section in chapter “Regulatory and Certification Information“. Added additional models in chapter “Ordering Information“. Formal and structure changes.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 7

1.3 Use of Symbols

Indicates important information for the proper use of the product. Non-observance can lead to errors. Attention Indicates important notes that, if not observed, can put the product’s functionality at risk.  [chapter number] [chapter title] Cross reference Indicates cross references within the document. Example: Description of the symbols used in this document  1.3 Use of Symbols.

1.4 Related Documents

Please refer to the Panasonic website for related documents  7.2.2 Product Information.

 PAN9026 Wi-Fi/Bluetooth Module

2 Overview

Product Specification Rev. 1.2 Page 8 The PAN9026 is a dual band 2.4 GHz and 5 GHz 802.11 a/b/g/n Wi-Fi radio module with integrated Bluetooth BR/EDR/LE, specifically designed for highly integrated and cost-effective applications. The simultaneous and independent operation of the two standards enables high data rates (802.11n) and low-power operation (Bluetooth Low Energy). Integrated power management, a fast dual-core CPU, 802.11i security standard support, and high-speed data interfaces deliver the performance for the speed, reliability, and quality requirements of next generation products. TX power calibration data and Wi-Fi/Bluetooth system parameters are pre-stored on the one-time-programmable memory of the PAN9026 during production at Panasonic. This simplifies passing the certification process for PAN9026 customers. Furthermore, the module reduces design, test, and calibration effort resulting in reduced time-to-market compared to discrete solutions. Integrating Wi-Fi and Bluetooth wireless connectivity allows applications such as Smart Energy and home gateways to manage multiple devices and appliances. The combination of Wi -Fi and Bluetooth provides the highest flexibility for connectivity. Please refer to the Panasonic website for related documents  7.2.2 Product Information. Further information on the variants and versions  7.1 Ordering Information.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 9

2.1 Block Diagram

32.768 kHz SPI UART COEX GPIOs Status LED's MCU Ready PDN Factory Reset V SPDT Wake Up's JTAG VIO 1.8 V BPF RF Pad PAN9026 Wi-Fi & Bluetooth Radio Module IEEE 802.11 a/b/g/n Bluetooth 5.0 (BR, LE & EDR) Crystal VDD 2.2 V VDD 1.8 V PCM Interface SDIO Interface VIO SD 32 kHz DISABLE RF SWVIO RF 3.3 VCNTL

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 10

2.2 Pin Configuration

No. Pin Name Pin Type Description A1 1 PCM_DOUT Output signal PCM data output signal IO5 Digital I/O General Purpose IO: GPIO[5] A2 32KHZ_IN NC Do not connect A3 PDN Input signal Power down (active-low) is derived from VDD1V8, can accept an input signal of 1.8 V to 3.6 V (external pull-up resistor), it can be driven by the host and must be high for normal operation. A4 VDD1V8 Power 1.7 V to 1.9 V (typ. 1.8 V) power supply connection A5 VDD1V8 Power 1.7 V to 1.9 V (typ. 1.8 V) power supply connection A6 VDD2V2 Power 2.1 V to 2.3 V (typ. 2.2 V) power supply connection A7 RF_SW1 Input signal RF Switch Pin 1: logical voltage level to activate on-board antenna or RF Pad  RF-Switch Pins Function A8 GND Ground pin Connect to ground A9 RF_OUT RF port 50  bottom pad to be activated by RF_SW1/RF_SW2 control voltage  RF-Switch Pins Function 1 Multi-purpose pins: After the firmware download, the pins (GPIO , Serial Interface, RF control) are programmed in functional mode with dedicated functionality. EP1 EP2 Chip Antenna 10,00 mm Ground plane keep out area Top View 17,50 mm

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 11 No. Pin Name Pin Type Description B1 1 PCM_CLK Input/output PCM clock signal, output if PCM master, input if PCM slave IO6 Digital I/O General Purpose IO: GPIO[6] B2 1 PCM_DIN Input signal PCM data input signal IO4 Digital I/O General Purpose IO: GPIO[4] B3 1 PCM_SYNC 2 Input/output PCM Sync Pulse signal, output if PCM master, input if PCM slave IO7 3 Digital I/O General Purpose IO: GPIO[7] B4 32KHZ_EN Input Signal If using VIO 3.3 V disable the internal 32.768 kHz crystal oscillator (100  to GND) to use the SoC reference clock with lower accuracy B5 VDD2V2 Power 2.1 V to 2.3 V (typ. 2.2 V) power supply connection B6 VDD2V2 Power 2.1 V to 2.3 V (typ. 2.2 V) power supply connection B7 RF_SW2 Input signal RF Switch Pin 2: logical voltage level to activate on-board antenna or RF Pad  RF-Switch Pins Function B8 GND Ground pin Connect to ground B9 GND Ground pin Connect to ground C1 IO2 Digital I/O General Purpose IO: GPIO[2] DVSC[0] Output signal Digital voltage scaling control for PMIC (VOUT 2.2 V)  2.3.1 Power Configuration Example with 3.3 V Host Operation C2 IO3 Digital I/O General Purpose IO: GPIO[3] DVSC[1] Output signal Digital voltage scaling control for PMIC (VOUT 1.05 V) (not used) C3 IO1 Digital I/O General Purpose IO: GPIO[1] C4 COEX_SIN Input signal Serial data input from MWS modem or peripheral device C9 GND Ground pin Connect to ground D1 IO15 Digital I/O General Purpose IO: GPIO[15] D2 IO14 Digital I/O General Purpose IO: GPIO[14] D3 DNC_E3 NC Do not connect D4 COEX_SOUT Output signal Serial data output to MWS modem or peripheral device D9 GND Ground pin Connect to ground E1 SD_CLK Digital I/O For SDIO specific terminals  SDIO Pins Function E2 SD_CMD Digital I/O For SDIO specific terminals  SDIO Pins Function E3 IO0 Digital I/O General Purpose IO: GPIO[0] E4 DNC_E4 NC Do not connect 2 PCM Mode: After enabling the mode by host command, the pin is used as PCM Audio Interface. 3 GPIO Mode: After enabling the mode by host command, the pin is us ed as Multi-Purpose Interface.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 12 No. Pin Name Pin Type Description E9 GND Ground pin Connect to ground F1 SD_DAT0 Digital I/O For SDIO specific terminals  SDIO Pins Function F2 SD_DAT1 Digital I/O For SDIO specific terminals  SDIO Pins Function F3 1 UART_SOUT 4 Output Signal Serial data output to peripheral device IO8 3 Digital I/O General Purpose IO: GPIO[8] BT_FREQ 5 Input Signal Information Bluetooth using channel which overlaps WLAN channel or not F4 1 UART_SIN 4 Input signal Serial data input to peripheral device IO9 3 Digital I/O General Purpose IO: GPIO[9] BT_STATE 5 Input signal Information BT_REQ priority (1-bit or 2-bit) and direction Bluetooth RX/TX F5 1 UART_RTS 4 Output signal Request-to-Send output to peripheral device IO11 3 Digital I/O General Purpose IO: GPIO[11] BT_REQ 5 Input signal Bluetooth device request access to medium F6 IO12 Digital I/O General Purpose IO: GPIO[12] F7 CNTL1 Output signal Do not connect F8 CNTL0 Input signal Keep open (DNC) if using SDIO interface for Bluetooth or connect with 100 k to GND if using UART interface for Bluetooth  Control Pin Function F9 GND Ground pin Connect to ground G1 SD_DAT2 Digital I/O For SDIO specific terminals  SDIO Pins Function G2 SD_DAT3 Digital I/O For SDIO specific terminals  SDIO Pins Function G3 VIOSD Power 1.8 V or 3.3 V Digital I/O SDIO power supply G4 VIO Power 1.8 V or 3.3 V power supply for General Purpose IO, if using VIO 3.3 V disable the internal 32.768 kHz crystal oscillator (Pin No. B4) G5 1 UART_CTS 4 Input signal Clear-to-send input from peripheral device IO10 3 Digital I/O General Purpose IO: GPIO[10] BT_GRANT 5 Output signal Indicate permission to transmit, low Bluetooth can transmit G6 IO13 Digital I/O General Purpose IO: GPIO[13] G7 VIORF Power 3 V to 3.6 V (typ. 3.3 V) power supply connection G8 DNC NC Do not connect G9 GND Ground pin Connect to ground 4 UART mode: After the dedicated firmware download, the pin is used as Host Controller Interface (HCI) for Bluetooth. 5 Bluetooth External Coexistence Mode: After enabling the mode by host command, the pin is used as Bluetoot h external Coexistence Interface.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 13 No. Pin Name Pin Type Description EP1 EPAD1 Thermal pin Connect to ground EP2 EPAD2 Thermal pin Connect to gorund

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 14 SDIO Pins Function No. Pin Name Pin Type Description 4-Bit Mode 1-Bit Mode E1 SD_CLK Digital I/O Clock Clock E2 SD_CMD Digital I/O Command Line Command Line F1 SD_DAT0 Digital I/O Data Line bit [0] Data Line F2 SD_DAT1 Digital I/O Data Line bit [1] or Interrupt (optional) Interrupt G1 SD_DAT2 Digital I/O Data Line bit [2] or Read Wait (optional) Read Wait (optional) G2 SD_DAT3 Digital I/O Data Line bit [3] Not used RF-Switch Pins Function No. Pin Name Pin Type Logical Level for Activation On-Board Chip Antenna RF OUT Pin A7 RF_SW1 Input signal 3 V to 3.6 V (typ. 3.3 V) GND (0 V) B7 RF_SW2 Input signal GND (0 V) 3 V to 3.6 V (typ. 3.3 V) Control Pin Function The control pin is used as configuration input to set parameters following a reset. The definition of the pin changes immediately after a reset to its usual function. To set a configuration bit to 0 bit, a 100 k resistor must be attached from the pin to ground. No external circuitry is required to set a configuration bit to 0 bit. No. Pin Name Pin Type Strap Value WLAN Bluetooth/ Bluetooth LE Firmware Download Number SDIO Functions Type Mode F8 CNTL0 Input Signal 0 SDIO UART SDIO+UART Parallel/Serial 1 (WLAN)

1 SDIO SDIO SDIO+SDIO Parallel/Serial 2 (WLAN,

Bluetooth) The configuration of the control pin is used for the firmware boot option. The software reads and boots accordingly.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 15

2.3 Power Management

2.3.1 Power Configuration Example with 3.3 V Host Operation 2.3.2 Power Configuration Example with 1.8 V Host Operation For further information please refer to  4.3.4 Power-up Sequence. PAN9026 VIO/VIO SD VIO RF VDD 2.2 V VDD 1.8 V DVSC[0] 88PG823 PMIC Enable VDD 3.3 V 3.3 V 3.3 V 2.2 V 1.8 V 3.3 V VDD 3.3 V or Host GPIO VIN R

100 Ohm

32KHZ_EN PAN9026 VIO/VIO SD VIO RF VDD 2.2 V VDD 1.8 V 3.3 V 2.2 V 1.8 V DC DC DC DC LDO Step-up Step-down VDD 1.8 V 1.8 V 1.8 V 3.3 V 3.3 V 2.2 V 2.2 V Dual

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 16

2.4 Host Interfaces

The bus interface connects several host interface bus units to the CPU bus of the device through the internal bus. The connection of each unit is multiplexed with other bus units. The high-speed UART interface is connected to the CPU bus through a separate bus. Type Features High-speed UART interface The device supports a high-speed Universal Asynchronous Receiver/Transmitter (UART) interface, compliant with the industry standard 16550 specification.

• FIFO mode permanently selected for transmit and receive operations
• Two pins for transmit and receive operations
• Two flow control pins
• Interrupt triggers for low-power, high throughput operation SDIO interface The device supports an SDIO device interface that conforms to the industry standard SDIO full-speed card specification and allows a host controller using the SDIO bus protocol to access the device.
• Supports SDIO 3.0 Standard
• 1-bit SDIO or 4-bit SDIO transfer modes with full clock range up to

100 MHz

• On-chip memory used for CIS
• Special interrupt register for information exchange
• Allows card to interrupt host For further information please refer to  4.3.5 Host Interface.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 17

2.5 Peripheral Bus Interface

The Peripheral Bus Unit (PBU) connects several low speed peripherals to the internal bus of the device. The device consists of the GPIO Interface and the One Time Programmable Memory. Type Features General Purpose I/O (GPIO) Interface

• User-defined GPIOs (each configured to either input or output)
• Each GPIO controlled independently
• Each I/O configurable to output bit from GPIO_OUT One Time Programmable Memory (OTP)
• Storing device-specific calibration data and hardware information like MAC/BD address, WLAN, and Bluetooth parameter
• Programmed during production process of device
• Device performs calibration when it is powered up For further information please refer to  4.3.6 Peripheral Interface.

2.6 PCM Interface

The device supports the PCM interface. Type Features PCM Interface • Master or slave mode

• PCM bit width size of 8 bits or 16 bits
• Up to four slots with configurable bit width and start positions
• Short frame and long frame synchronization For further information please refer to  4.3.7 Audio Interface.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 18

2.7 Coexistence

The implemented coexistence framework is based on the IEEE 802.15.2 recommended prac tice Packet Traffic Arbitration (PTA) scheme and the Bluetooth Special Interest Group (Bluetooth SIG) Core Specification Volume 7 (Wireless Coexistence Volume).

2.7.1 WLAN/Bluetooth Channel Information Exchange

Since Bluetooth and IEEE 802.11 b/g/n WLAN use the same 2.4 GHz frequency band, each can cause interference with another. The level of interference depends on the respective frequency channel used by Bluetooth and WLAN (other factors can impact interference, like Tx power and Rx sensitivity of the device). In a system with both Bluetooth and WLAN, the common host receives information about WLAN channel usage and passes the information to the Bluetooth device. For Bluetooth 1.2 devices with Adaptive Frequency Hopping (AFH) enabled, the Bluetooth device can block channel usage that overlaps the WLAN channel in use. When the Bluetooth device avoids all channels used by the WLAN, the impact of interference is reduced, but not completely eliminated. For Bluetooth 1.1 devices, the Bluetooth device cannot block WLAN channel usage. In this case, a Bluetooth Coexistence Arbiter (BCA) scheme at MAC level is required. The BCA scheme can also be used with Bluetooth 1.2 devices to further reduce the impact of interference to a minimum.

2.7.2 External Mobile Wireless System (LTE/ZigBee®) and BCA Exchange

Based on the Bluetooth SIG Wireless Coexistence Volume, the device supports a Wireless Coexistence Interface 2 (WCI-2) protocol for WLAN and Bluetooth coexistence with an external Mobile Wireless System (MWS), such as a Long Term Evolution (LTE) or ZigBee device. WCI-2 is a 2-wire transport interface. An internal coexistence is used to exchange request/grant with the BCA.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 19

2.7.3 System Configuration

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 20

2.7.4 WCI-2 Interface

The coexistence interface includes a Mobile Wireless System (MWS) transport controller to accommodate a 2-wire, UART-based serial transport interface. This interface is a standard full-duplex UART (TXD and RXD) carrying logical signals framed as UART characters. In addition, it allows support of multiple logical channels. Interface Signals Pin No. Signal Name Specification Name Pin Type Description C4 COEX_SIN RXD Input Serial data from external MWS device D4 COEX_SOUT TXD Output Serial data to external MWS device Signal Waveform Format The messaging is based on a standard UART format. The UART signals should be connected like a null-modem. For example, the local TXD connected to the remote RXD and vice versa. Interface Transport Settings Item Range Comment Baudrate 921 600 to 4 000 000 Baud Data Bits 8 LSB first Parity Bits 0 No parity Stop Bit 1 One stop bit Flow Control No No flow control Supported Baud Rates Baud 921 600 2 000 000 3 000 000 4 000 000

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 21 Real-Time Signaling Message The real-time signaling message is used to transport real-time signals over the 2-wire transport interface. The real-time signaling message conveys the real-time signals (Bluetooth Core Specification, Volume 7, Part A) in one message. The time reference point for the real-time signaling message is the end of message bit 5 (transition to stop bit). Defined real-time signaling messages include:

• Coexistence Controller to MWS device
• MWS device to Coexistence Controller Real-Time Signaling MSG[0] MSG[1] MSG[2] MSG[3] MSG[4] MWS to Coexistence Controller (Signal) FRAME_SYNC MWS_RX MWS_TX PATTERN[0] PATTERN[1] Coexistence Controller to MWS (Message) BT_RX_PRI BT_TX_ON 802_RX_PRI 802_TX_ON RFU Signal Name FRAME_SYNC MWS_RX MWS_TX PATTERN[1,0] BT_RX_PRI BT_TX_ON 802_RX_PRI 802_TX_ON MWS_INACTIVITY_DURATION MWS_SCAN_FREQUENCY_OFFSET

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 22 Transport Control Message The transport control messages can modify the state and request state information of the MWS coexistence interface. Message MSG[0] MSG[1] MSG[2] MSG[3] MSG[4] Transport Control Message RESEND_REA L_TIME RFU RFU RFU RFU Signal Name Description RESEND_REAL_TIME This bit is set if a device wants to get a status update of the real-time signals. The signal is usually used after wake-up from sleep of the transport interface to get an update of the real-time signals. If the receiving device’s transport interface is awake it shall send a real-time message with the current status of the real-time signals within four UART character period. If the signal is not transmitted within four UART character periods, the device is considered asleep. If the receiving device’s transport interface is not awake it shall not send a real-time message. Bluetooth initiated: If the MWS is currently scanning or has an ongoing inactivity duration, the MWS shall send a frequency scan message or an inactivity duration message after transmitting the real-time message. If the receiving device’s transport interface is not awake it shall not send a frequency scan or inactivity duration message. Transparent Data Message The transport control messages can modify the state and request state information of the MWS coexistence interface. Message MSG[0] MSG[1] MSG[2] MSG[3] MSG[4] Transparent Data Message NIBBLE_POS ITION DATA[0]/ DATA[4] DATA[1]/ DATA[5] DATA[2]/ DATA[6] DATA[3]/ DATA[7] Signal Name Description NIBBLE_POSITION 0 = least significant nibble 1 = most significant nibble DATA[n]; n=0 … 7 Data bits of the message octet

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 23 MWS Inactivity Duration Message The inactivity duration messages is used to send the signal MWS_INACTIVITY_DURATION from the MWS device to the Coexistence Controller. Message MSG[0] MSG[1] MSG[2] MSG[3] MSG[4] MWS Inactivity Duration Message DURATION[0] DURATION[1] DURATION[2] DURATION[3] DURATION[4] The idle duration is encoded in 5 bits given by the formula: Inactivity_Duration = DURATION * 5 ms Inactivity durarations smaller than 5 ms are not communicated. If all bits are set to 1 the inactivity duration is infinite. If all bits are set to 0, signal MWS_RX, or signal MWS_TX are set to 1, the inactivity period ends. MWS Scan Frequency Offset Message The MWS scan frequency offset message is used to send the signal MWS_SCAN_FREQUENCY_ OFFSET from the MWS device to the Coexistence Controller. Message MSG[0] MSG[1] MSG[2] MSG[3] MSG[4] MWS Scan Frequency Offset BAND FREQ[0] FREQ [1] FREQ [2] FREQ [3] The RF scan frequency is encoded in 5 bits given by the formula: RF_FREQ_OFFSET = FREQ * 10 MHz If BAND is set to o the signal RF_FREQ_OFFSET is the negative value from the lower edge of the ISM band. If BAND is set to 1, signal RF_FREQ_OFFSET is the positive value from the top edge of the ISM band. FREQ set to all 0 indicates the end of the scan period.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 24

2.7.5 Bluetooth Coexistence Arbiter

Capability • Programmable coexistence interface timing, interface modes, and signal polarity to support a variety of external Bluetooth devices

• Programmable decision policies and transaction lock behavior for various use cases
• Interface with external or on-chip Bluetooth device
• Supports Bluetooth 1.1 or Bluetooth 1.2 AFH
• WLAN-coordinated/Bluetooth-coordinated low-power design
• Enhanced information sharing between WLAN and Bluetooth for combined systems
• WLAN/Bluetooth/MWS (LTE/ZigBee) coexistence support Arbitration • Contention resolved by a customizable decision matrix that allows independent grant decision for each device
• Vectors for the decision matrix:  WLAN priority (2-bit)  WLAN direction  Bluetooth priority (1-bit or 2-bit)  Bluetooth direction  Bluetooth frequency in/out band  MWS priority (2-bit)  MWS direction AFH If AFH is enabled in the Bluetooth device, and there is a sufficient guard-band outside the WLAN operating frequency, the Bluetooth device uses the Out-Of-Band (OOB) channel with respect to the WLAN device. Otherwise, the Bluetooth device uses the In-Band (IB) and OOB channels with respect to the WLAN device. The IB and OOB information is either provided by the Bluetooth device through the coexistence interface, or it can be provided through firmware controls in a shared-host system. IB/OOB is a vector in the decision matrix.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 25 Type Features Decision Policies System configuration is a major consideration when planning decision policies. The configuration governs how RF paths are shared and how much interference will occur. Interference combinations include:  WLAN TX and Bluetooth TX  WLAN TX and Bluetooth RX  WLAN RX and Bluetooth TX  WLAN RX and Bluetooth RX Interference combinations where WLAN and Bluetooth share the same antenna:  WLAN TX and Bluetooth TX share the same antenna, the decision matrix allows either WLAN or Bluetooth TX (both OOB and IB), based on relative packet priorities.  WLAN TX and Bluetooth RX (both OOB and IB) have sizable interference impacts on Bluetooth RX, the decision matrix grants or denies WLAN TX based on relative packet priorities.  WLAN RX and Bluetooth TX (both OOB and IB) have sizable interference impacts on WLAN RX, the decision matrix grants or denies Bluetooth TX based on relative packet priorities.  WLAN RX and Bluetooth RX (both OOB and IB) have no impact on each other, the decision matrix grants both. Interference combinations where WLAN and Bluetooth have their own antenna:  WLAN TX and Bluetooth TX in OOB situation have little interference impact on each other, the decision matrix grants both.  WLAN TX and Bluetooth TX in IB have sizable interference impact on each other, the decision matrix allows either WLAN or Bluetooth TX, based on relative packet priorities.  WLAN TX and Bluetooth RX in OOB situation have little interference impact on each other, the decision matrix grants both provided there is enough antenna isolation between WLAN and Bluetooth antenna.  WLAN TX and Bluetooth RX in IB situation have sizable interference impact on Bluetooth RX, the decision matrix grants or denies WLAN TX based on relative packet priorities.  WLAN RX and Bluetooth TX in OOB situation have little interference impact on each other, the decision matrix grants both provided there is enough antenna isolation between WLAN and Bluetooth antenna.  WLAN RX and Bluetooth TX in IB situation have sizable interference impact on WLAN RX, the decision matrix grants or denies Bluetooth TX based on relative packet priorities.  WLAN RX and Bluetooth RX (both OOB and IB) have no impact on each other, the decision matrix grants both. For the devices running in a basic shared antenna configuration, the linear switching imposes restrictions on simultaneous transfer. Reasonable policies include:  WLAN and Bluetooth are never granted at the same time  Decision matrix grants a device based on relative packet priorities and direction  Priority order: High > Medium High > Medium > Low  For equal priority contention, select one device to win, that optimizes the usage case For the devices running in an enhanced shared antenna configuration, the linear switching imposes restrictions on some simultaneous transfers.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 26 Type Features Transaction Stopping The arbiter allows control of what transfers can be stopped after an initial grant. If allowed, a transaction can be stopped for higher priority request. A transaction stop decision is a function of the decision policies and transaction stopping control. The transaction stopping control is configurable per device and direction.

2.7.6 Bluetooth Capability

Request Schemes The PTA signals are directly controlled by the hardware to meet timing requirements of the Bluetooth radio. The software controls the type of traffic in priority mode. Mechanism enforced for control include:

• Selection of certain types of communication always treated as high priority
• Selection of individual frames marked with high priority
• Real-time signaling of the next slot marked with high priority
• Automatic hardware control, based on the grant/denial history of the Bluetooth link Timing Control The signal timing scheme PTA is fully programmable relative to the Bluetooth packet timing.

2.7.7 WLAN Capability

Capability The WLAN device technology uses an internal coexistence interface to exchange request/grant with the BCA.

• Packet-based request signaling with direction and priority information
• 1-bit or 2-bit priority signaling to support four priority levels
• Multiple WLAN RX request trigger sources, including early prediction
• WLAN TX request cancellation and abort if grant denied or revoked in middle of request
• 802.11n A-MPDU treated as single packet Packet Classification • Programmable mask allows each frame type to be mapped to a priority
• Default setting puts response frames (ACK), beacons, and QoS frames as high priority
• WLAN TX and RX have separate priority mask Queue Classification • Programmable mask allows each transmit queue to be mapped to a priority
• Queue-based mapping is optional for software-generated frames only

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 27

2.7.8 LTE (MWS) Capability

The device supports a Bluetooth SIG WCI-2 MWS coexistence signaling interface. The coexistence logical signaling is designed to enable a standard interface to allow an MWS device and a Coexistence Controller to exchange information and support cooperative coexistence. The WCI-2 signals carry time-critical information such as the start point of an MWS frame. The logical coexistence signaling architecture also includes transparent data messaging and vendor specific data messaging mechanism to enable passing information to and from the collocated MWS device and Coexistence Controller when long latency (tens of milliseconds) cannot be tolerated. For further information please refer to  2.7.4 WCI-2 Interface. Coexistence Signals The logical signals assist in time alignment, protecting MWS from interference and maximizing the usability of the Bluetooth radio. Time-Critical Coexistence Signals Signal Name Direction FRAME_SYNC MWS to Bluetooth BT_RX_PRI Bluetooth to MWS BT_TX_ON Bluetooth to MWS 802_RX_PRI Bluetooth to MWS 802_TX_ON Bluetooth to MWS MWS_PATTERN MWS to Bluetooth MWS_RX MWS to Bluetooth MWS_TX MWS to Bluetooth MWS_INACTIVITY_DURATION MWS to Bluetooth MWS_SCAN_FREQUENCY_OFFSET MWS to Bluetooth MWS_TX_PRIL (MWS TX Priority Level) MWS to Bluetooth MWS_RX_PRIL (MWS RX Priority Level) MWS to Bluetooth

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 28

2.7.9 ZigBee (MWS) Coexistence Capability

ZigBee is based on the IEEE 802.15.4 standard and it is used by a suite of communication protocols to create Personal Area Networks (PANs) supporting home automation, lighting control, etc. ZigBee radios operate in the 2.4 GHz ISM band worldwide. Unlike Bluetooth, the ZigBee specification does not use AFH. When coexisting with WLAN/Bluetooth in the 2.4 GHz band, it is important to avoid co-channel (IB) operation of these radios. The device re-uses the MWS coexistence interface to support ZigBee coexistence. The coexistence logical signaling is used to allow a ZigBee device and a WLAN/B luetooth combined device to exchange information and support cooperative coexistence. Coexistence Signals The logical signals used for ZigBee and WLAN/Bluetooth coexistence are a subset of the LTE coexistence signaling. Considering the lower data rate of ZigBee packets, a lower baud rate may be chosen for the 2-wire UART physical interface. The BCA supports 3-way arbitration among ZigBee/WLAN/Bluetooth requests. Coexistence Signals Signal Name Direction MWS_RX MWS to Bluetooth MWS_TX MWS to Bluetooth MWS_PATTERN MWS to Bluetooth MWS_RX_PRI MWS to Bluetooth MWS_TX_PRI MWS to Bluetooth 802_RX_PRI Bluetooth to MWS 802_TX_ON Bluetooth to MWS BT_RX_PRI Bluetooth to MWS BT_TX_ON Bluetooth to MWS

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 29

2.8 WLAN

IEEE 802.11/ Standards

• 802.11 data rates 1 and 2 Mbps (DSSS)
• 802.11b data rates 5.5 and 11 Mbps (CCK)
• 802.11a/g data rates 6, 9, 12, 18, 24, 36, 48, and 54 Mbps (OFDM)
• 802.11b/g performance enhancements
• 802.11n with maximum data rates up to 72 Mbps (20 MHz channel) and

150 Mbps (40 MHz channel)

• 802.11e quality of service (QoS)
• 802.11h transmit power control
• 802.11h DFS radar pulse detection
• 802.11i enhanced security (WEP, WPA, WPA2)
• 802.11k radio resource measurement
• 802.11mc precise indoor location and navigation
• 802.11n block acknowledgment extension
• 802.11r fast hand-off for AP roaming
• 802.11u Hotspot 2.0 (STA mode only)
• 802.11v TIM frame transmission/reception
• 802.11w protected management frames
• Support clients (stations) implementing IEEE Power Save mode WLAN MAC • Frame exchange at the MAC level to deliver data
• Received frame filtering and validation (CRC)
• Generation of MAC header and trailer information (MPDUs)
• Fragmentation of data frames (MSDUs)
• Access mechanism support for fair access to shared wireless medium through:  Distributed Coordination Function (DCF)  Enhanced Distributed Channel Access (EDCA)
• A-MPDU aggregation/de-aggregation
• 20 MHz and 40 MHz channel coexistence
• RIFS burst receive
• Management information base
• Radio resource measurement
• Quality of service
• Block acknowledgement
• Dynamic frequency selection
• TIM frame TX and RX
• Multiple BSS/Station
• Transmit rate adaption
• Transmit power control

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 30 Type Features WLAN Baseband • 802.11n 1x1 SISO (WLAN SoC with SISO RF radio)

• Backward compatibility with legacy 802.11a/b/g technology
• WLAN/Bluetooth LNA sharing
• PHY data rates up to 150 Mbps
• 20 MHz bandwidth/channel, 40 MHz bandwidth/channel, upper/lower

20 MHz bandwidth in 40 MHz channel, and 20 MHz duplicate legacy

bandwidth in 40 MHz channel mode operation

• Modulation and Coding Scheme MCS 0 ~ 7 and MCS 32 (duplicate

6 Mbps)

• Dynamic frequency selection (radar detection) – Enhanced radar detection for short and long pulse radar – Enhanced AGC scheme for DFS channel – Japan DFS requirement for W53 and W56
• 802.11k Radio resource measurement
• 802.11n optional features:  20 MHz and 40 MHz coexistence  Space-Time-Block-Coding (STBC) one spatial stream reception and transmission  Short Guard Interval for both 20 MHz and 40 MHz operation (TX/RX)  RIFS on receive path  Beamformer function and hardware acceleration  Greenfield TX/RX
• 802.11mc locationing
• Power save features WLAN Radio • Integrated direct-conversion radio
• 20 MHz and 40 MHz channel bandwidth
• Shared WLAN/Bluetooth receive input scheme for 2.4 GHz band
• RX Path  On-chip gain selectable LNA with optimized noise figure and power consumpttion  High dynamic range AGC function in receive mode
• TX Path  Internal PA with power control  Optimized TX gain distribution for linearity and noise performance
• Local Oscillator with fine channel step WLAN Encryption • WEP 64-bit and 128-bit encryption with hardware TKIP processing (WPA)
• AES-CCMP hardware implementation as part of 802.11i security standard (WPA2)
• Enhanced AES engine performance
• Advanced encryption standard (AES)/Counter-Mode/CBC-MAC Protocol (CCMP)
• AES-Cipher-Based Message Authentication Code (CMAC) as part of the 802.11w security standard
• WLAN Authentication and Privacy Infrastructure (WAPI)

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 31 Operation Modes Parameter Operation Mode Specification Standard Conformance IEEE 802.11/IEEE 802.11b IEEE 802.11a IEEE 802.11g IEEE 802.11n Modulation IEEE 802.11a OFDM IEEE 802.11b DSSS/CCK IEEE 802.11g OFDM IEEE 802.11n OFDM @ MCS0~7 and MCS32 (duplicate Physical Layer Data Rates IEEE 802.11 1, 2 Mbps @ DSSS IEEE 802.11b 5.5, 11 Mbps @ DSSS/CCK Supported Data Rates IEEE 802.11g 6, 9, 12, 18, 24, 36, 48, 54 Mbps IEEE 802.11a 6, 9, 12, 18, 24, 36, 48, 54 Mbps IEEE 802.11n MCS0~7 HT20 LGI 6.5, 13, 19.5, 26, 39, 52, 58.5, 65 Mbps

72.2 Mbps

HT40 LGI 13.5, 27, 40.5, 54, 81, 108, 121.5,

135 Mbps

SGI 15, 30, 45, 60, 90, 120, 135, 150 Mbps Supported Bandwidth IEEE 802.11n 20, 40 MHz (BW) Supported Channel Mode Operation IEEE 802.11n 20 MHz BW/channel, 40 MHz BW/channel, upper/lower 20 MHz BW @ 40 MHz channel, 20 MHz duplicate legacy BW @ 40 MHz channel Supported Guard Interval IEEE 802.11n 400 ns (SGI), 800 ns (LGI)

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 32 Channels and Frequencies (without Regulatory Restrictions) 2.4 GHz IEEE 802.11b/g/n

20 MHz Channels 40 MHz Channels

Channel Frequency Unit Channel Frequency Unit 1 2 412 MHz 1-5 2 422 MHz 2 2 417 MHz 2-6 2 427 MHz 3 2 422 MHz 3-7 2 432 MHz 4 2 427 MHz 4-8 2 437 MHz 5 2 432 MHz 5-9 2 442 MHz 6 2 437 MHz 6-10 2 447 MHz 7 2 442 MHz 7-11 2 452 MHz 8 2 447 MHz 9 2 452 MHz 10 2 457 MHz 11 2 462 MHz 12 2 467 MHz 13 2 472 MHz 5 GHz IEEE 802.11a/n Channel Frequency Unit Channel Frequency Unit 36 5 180 MHz 36-40 5 190 MHz 40 5 200 MHz 44-48 5 230 MHz 44 5 220 MHz 52-56 5 270 MHz 48 5 240 MHz 60-64 5 310 MHz 52 5 260 MHz 56 5 280 MHz 60 5 300 MHz 64 5 320 MHz 100 5 500 MHz 100-104 5 510 MHz 104 5 520 MHz 108-112 5 550 MHz 108 5 540 MHz 116-120 5 590 MHz 112 5 560 MHz 124-128 5 630 MHz 116 5 580 MHz 132-136 5 670 MHz 120 5 600 MHz 124 5 620 MHz 128 5 640 MHz 132 5 660 MHz 136 5 680 MHz 140 5 700 MHz

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 33 5 GHz IEEE 802.11a/n Channel Frequency Unit Channel Frequency Unit 149 5 745 MHz 149-153 5 755 MHz 153 5 765 MHz 157-161 5 795 MHz 157 5 785 MHz 161 5 805 MHz 165 5 825 MHz 5 GHz IEEE 802.11a/n (India and additional UNII Channels) Channel Frequency Unit Channel Frequency Unit 144 5 720 MHz 68-72 5 350 MHz 1696 5 845 MHz 76-80 5 390 MHz 173 5 865 MHz 84-88 5 430 MHz 177 5 885 MHz 92-96 5 470 MHz 181 5 905 MHz 140-144 5 710 MHz 165-169 5 835 MHz 169-1737 5 855 MHz 173-177 5 875 MHz

6 India channels that can be used in other countries as well

7 India use only

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 34 Channel Tables based on Regulatory Domain/Country 2.4 GHz IEEE 802.11b/g/n

802.11 Operation Mode

0 = disable 1 = enable Device Mode Y = Yes/N = No Data Rates 1M - 11M 6M - 18M 24M - 36M 48M - 54M MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 Model Variant 8 Channel 20M Channel 40M Frequenz Unit TX Power (maximum) Unit DFS Passive Scan Master Client US, EU, CA, MR 1 2 412 MHz 15 15 15 14 14 14 13 - - - dBm 0 0 Y Y 2 2 417 MHz 16 16 16 15 15 15 14 - - - dBm 0 0 Y Y 3 1-5 2 422 MHz 16 16 16 15 15 15 14 13 13 12 dBm 0 0 Y Y 4 2-6 2 427 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 5 3-7 2 432 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 6 4-8 2 437 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 7 5-9 2 442 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 8 6-10 2 447 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 9 7-11 2 452 MHz 16 16 16 15 15 15 14 13 13 12 dBm 0 0 Y Y 10 - 2 457 MHz 16 16 16 15 15 15 14 - - - dBm 0 0 Y Y US, CA, MR 11 - 2 462 MHz 15 15 15 14 14 14 13 - - - dBm 0 0 Y Y 12 - 2 467 MHz - - - - - - - - - - dBm 0 0 N N 13 - 2 472 MHz - - - - - - - - - - dBm 0 0 N N EU 10 8-12 2 457 MHz 16 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 11 9-13 2 462 MHz 16 16 16 15 15 15 14 13 13 12 dBm 0 0 Y Y 12 - 2 467 MHz 16 16 16 15 15 15 14 - - - dBm 0 0 Y Y 13 - 2 472 MHz 15 15 15 14 14 14 13 - - - dBm 0 0 Y Y 8 The country related module variants are using a channel table with TX Power, DFS, and Passive Scan settings, which is pre - stored and locked in the OTP memory of the module and cannot be changed by host driver API. Please find the model variants restricted to a particular regulatory domain at the variant table of Ordering Information.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 35 5 GHz IEEE 802.11a/n 0 = disable 1 = enable Device Mode Y = Yes/N = No Data Rates 6M - 18M 24M - 36M 48M - 54M MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 Model Variant Channel 20M Channel 40M Frequenz Unit TX Power (maximum) Unit DFS Passive Scan Master Client US, EU, CA, MR 5 180 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 40 5 200 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 5 220 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 48 5 240 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y US, EU, CA 5 260 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 56 5 280 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 5 300 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 64 5 320 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y MR 52 US, EU, CA 100 102 5 500 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 104 5 520 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 108 110 5 540 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 112 5 560 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y MR 100 102 108 110 US, EU 116 118 5 580 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 120 5 600 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 124 126 5 620 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 128 5 640 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y CA 116 118 5 580 MHz 16 16 15 15 15 14 - - - dBm 1 1 Y Y 124 126

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 36 5 GHz IEEE 802.11a/n 0 = disable 1 = enable Device Mode Y = Yes/N = No Data Rates 6M - 18M 24M - 36M 48M - 54M MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 MCS0 – MCS2 MCS3 – MCS4 MCS5 – MCS7 Model Variant Channel 20M Channel 40M Frequenz Unit TX Power (maximum) Unit DFS Passive Scan Master Client MR 116 118 124 126 US, CA, EU 132 134 5 660 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 136 5 680 MHz 16 16 15 15 15 14 14 14 13 dBm 1 1 Y Y 140 - 5 700 MHz 16 16 15 15 15 14 - - - dBm 1 1 Y Y MR 132 134 US, CA 149 151 5 745 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 153 5 765 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 157 159 5 785 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 161 5 805 MHz 16 16 15 15 15 14 14 14 13 dBm 0 0 Y Y 165 - 5 825 MHz 16 16 15 15 15 14 - - - dBm 0 0 Y Y EU, MR 149 151 5 745 MHz 10 10 9 10 10 9 9 9 8 dBm 0 0 Y Y 153 5 765 MHz 10 10 9 10 10 9 9 9 8 dBm 0 0 Y Y 157 159 5 785 MHz 10 10 9 10 10 9 9 9 8 dBm 0 0 Y Y 161 5 805 MHz 10 10 9 10 10 9 9 9 8 dBm 0 0 Y Y 165 - 5 825 MHz 10 10 9 10 10 9 - - - dBm 0 0 Y Y

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 37

2.9 Bluetooth

General • Supports Bluetooth 5.0

• Shared Tx/Rx path for Bluetooth
• Digital Audio Interface including PCM interface for voice application
• Bluetooth and WLAN coexistence
• WLAN/Bluetooth Coexistence (BCA) protocol support Bluetooth Classic (BR/EDR)
• Bluetooth Classic with Bluetooth Class 1 support
• Baseband and radio Basic Rate (BR) and Enhanced Data Rate (EDR) packet types with 1 Mbps (GFSK), 2 Mbps (π/4-DQPSK) and 3 Mbps (8DPSK)
• Fully functional Bluetooth baseband with: – Adaptive Frequency Hopping (AFH) – Forward error correction – Header error control – Access code correlation – CRC – Encryption bit stream generation – Whitening
• Adaptive Frequency Hopping (AFH) including Packet Loss Rate (PLR)
• Interlaced scan for faster connection setup
• Simultaneous active ACL connection support
• Automatic ACL packet type selection
• Full master slave piconet support
• Scatternet support
• Standard UART and SDIO HCI transport layer
• SCO/eSCO links with hardware accelerated audio signal pocessing and hardware supported PPEC algorithm for speech quality improvement
• All standard SCO/eSCO voice coding
• All standard pairing, authentication, link key, and encryption operations
• Standard Bluetooth power saving mechanism (i.e. hold, sniff modes, and sniff-sub rating)
• Enhanced Power Control (EPC)
• Channel Quality Driven (CQD) data rate
• Wideband Speech (WBS) support (1 WBS link)
• Encryption (AES) support
• LTE/MWS coexistence

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 38 Type Features Bluetooth Low Energy (LE) • Broadcaster, Observer, Central, and Peripheral roles

• Supports link layer topology to be master and slave (connects up to 16 links)
• Shared RF with BR/EDR
• Encryption AES support
• Hardware support for intelligent Adaptive Frequency Hopping (AFH)
• LE Privacy 1.2
• LE Secure Connection
• LE Data Length Extension
• LE Advertising Length Extension
• Direction Finding, Connection-oriented Angle of Arrival (AoA)

 PAN9026 Wi-Fi/Bluetooth Module

3 Detailed Description

Product Specification Rev. 1.2 Page 39

3.1 Dimensions

All dimensions are in millimeters. No. Item Dimension Tolerance Remark 1 Width 10.00 ± 0.35 2 Length 17.50 ± 0.35 3 Height 2.55 ± 0.20 with case 17,50 2,55

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 40

3.2 Footprint

The outer dimensions have a tolerance of  0.35 mm. 8,80 mm 2,20 mm2,20 mm 6,00 mm 3,20 mm 6,80 mm 0,80 mm 0,80 mm 0,80 mm Chip Antenna 0,80 mm 2,20 mm 3,60 mm 5,00 mm 17,50 mm 6,40 mm 7,80 mm 9,20 mm 10,60 mm 12,00 mm 1,40 mm 12,00 mm 4,80 mm 8.00 mm1.00 mm 1.00 mm 2,20 mm 0,80 mm 3,60 mm 5,00 mm 6,40 mm 7,80 mm 9,20 mm 10,00 mm Ground plane keep out area Top View EP1 EP2

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 41

3.3 Packaging

The product is a mass production status product and will be delivered in the package described below.

3.3.1 Tape Dimensions

3.3.2 Packing in Tape

Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. The top cover tape shall not be found on reel holes and it shall not stick out from the reel. W Do 1.5 +0.1 0.0 PoP2 E1 Ao 2.0MIN F(III) So X X A Y Y SECTION X-X 0.20 ± 0.05 R0.75 DETAIL A Ko T 0.30± 0.03 Bo SECTION Y-Y Measured from centreline of sprocket hole to centreline of pocket. Cumulative tolerance of 10 sprocket holes is ± 0.20 . Measured from centreline of sprocket hole to centreline of pocket. (I) (II) (III) (IV) Other material available. ALL DIMENSIONS IN MILLIMETRES UNLESS OTHERWISE STATED.W F S O +/- 0.15 +/- 0.15 +/- 0.3 14.20 28.40 32.00 Ao 18.05 +/- 0.15Bo 3.00 +/- 0.15 20.00P 1 +/- 0.15 Ko 10.55 +/- 0.15 100730-PAN1720.vsd trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules. Direction of unreeling (for customer)

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 42

3.3.3 Component Direction

3.3.4 Reel Dimension

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 43

3.3.5 Package Label

(1T) (1P) (2P) (9D) (Q) (HW/SW) Lot code Customer order number, if applicable Order number Date code Quantity Hardware/software version

3.3.6 Total Package

(already exist on barrier bag) barcode label desiccant 1) 2) moisture indicator barrier bag sealed inner carton box size 340 x 340 x 41 mm³ 1) quantity of desiccant according to calculation 2) optional: desiccant placed into the corner of the barrier bag

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 44

3.4 Case Marking

Example for PAN9026 (top view) Brand name Hardware/Software version Engineering Sample (optional) Model Name/ENW number Lot code Serial number WLAN MAC address BD address Certification grant ID Marking for Pin 1 2D barcode, for internal usage only Bluetooth SIG logo

 PAN9026 Wi-Fi/Bluetooth Module

4 Specification

Product Specification Rev. 1.2 Page 45 All specifications are over temperature and process, unless indicated otherwise.

4.1 Default Test Conditions

Temperature: 25 °C ± 10 °C Humidity: 40 % to 85 % RH Supply Voltage: VDD2V2 = 2.2 V VDD1V8 = 1.8 V VIORF = 3.3 V VIOSD = 3.3 V VIO = 1.8 V

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 46

4.2 Absolute Maximum Ratings

The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TSTOR Storage Temperature -40 85 °C VESD ESD Robustness All pads, according to human body model (HBM), JEDEC STD 22, method A114 1 000 V According to charged device model (CDM), JEDEC STD 22, method C101 500 V PRF RF Input Level 20 dBm VDD1V8 Maximum Voltage Maximum power supply voltage from any pin with respect to VSS (GND) 1.8 1.98 V VDD2V2 2.2 2.3 V VIOSD 1.8 2.2 V 3.3 4 V VIO 1.8 2.2 V 3.3 4 V VIORF 3.3 4 V VRF_SW1/2 3.3 4 V

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 47

4.3 Recommended Operating Conditions

The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TA Ambient Operating Temperature Range Extended grade -30 85 °C VDD1V8 1V8 Supply Voltage9 VDD voltage for Baseband and CPU on pins A4, A5 1.71 1.80 1.89 V VDD2V2 2V2 Supply Voltage9 VDD voltage for VGA on pins A6, B5, B6 2.09 2.20 2.26 V VIOSD Digital I/O VIOSD Supply Voltage10 Pin G3 with 1.8 V operation  SDIO Pins Function 1.62 1.80 1.98 V Pin G3 with 3.3 V operation  SDIO Pins Function 2.97 3.30 3.47 V VIO Digital I/O VIO Supply Voltage Pin G4 with 1.8 V operation 1.62 1.80 1.98 V Pin G4 with 3.3 V operation Pin B4 connect to GND11 2.97 3.30 3.47 V VIORF Digital I/O VIORF Supply Voltage9 Pin G7 with 3.3 V operation 2.97 3.30 3.47 V VRF_SW1/2 VRF_SW1/2 Switch Voltage9 Pin A7, B7 with 3.3 V logical level switch operation  RF-Switch Pins Function 2.97 3.30 3.60 V

9 The power consumption should not exceed 15 Watt

10 1.8 V or 3.3 V supply voltage possible 11 Connect the 32KHZ_EN pin via a 100  resistor to ground to disable the internal 32.768 kHz crystal oscillator. The low power modes will then use the SoC reference clock, which has lower accuracy.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 48

4.3.1 Digital Pin Characteristics

VIO with 1.8 V Operations12 Symbol Parameter Condition Min. Typ. Max. Units VIH High Level Input Voltage 1.8 V operation (VIO = 1.8 V) 0.7 VIO VIO +0.4 V VIL Low Level Input Voltage 1.8 V operation (VIO = 1.8 V) -0.4 0.3 VIO V VHYS Input Hysteresis 100 mV VOH High Level Ouput Voltage 1.8 V operation (VIO = 1.8 V) VIO -0.4 V VHO Low Level Output Voltage 1.8 V operation (VIO = 1.8 V) 0.4 V VIO with 3.3 V Operations12 Symbol Parameter Condition Min. Typ. Max. Units VIH High Level Input Voltage 3.3 V operation (VIO = 3.3 V) 0.7 VIO VIO +0.4 V VIL Low Level Input Voltage 3.3 V operation (VIO = 3.3 V) -0.4 0.3 VIO V VHYS Input Hysteresis 100 mV VOH High Level Ouput Voltage 3.3 V operation (VIO = 3.3 V) VIO -0.4 V VHO Low Level Output Voltage 3.3 V operation (VIO = 3.3 V) 0.4 V VIOSD 1.8 V Operation for SDIO I/F12 Symbol Parameter Condition Min. Typ. Max. Units VIH High Level Input Voltage 1.8 V operation (VIOSD = 1.8 V) 0.7 VIOSD VIOSD +0.4 V VIL Low Level Input Voltage 1.8 V operation (VIOSD = 1.8 V) -0.4 0.3 VIOSD V VHYS Input Hysteresis 100 mV VOH High Level Ouput Voltage 1.8 V operation (VIOSD = 1.8 V) VIOSD -0.4 V VHO Low Level Output Voltage 1.8 V operation (VIOSD = 1.8 V) 0.4 V 12 The capacitive load should not be larger than 50 pF for all I/Os when using the default driver strength settings. Large capacitance loads generally increase the overall current consumption.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 49 VIOSD 3.3 V Operation for SDIO I/F12 Symbol Parameter Condition Min. Typ. Max. Units VIH High Level Input Voltage 3.3 V operation (VIOSD = 3.3 V) 0.7 VIO_SD VIO_SD +0.4 V VIL Low Level Input Voltage 3.3 V operation (VIOSD = 3.3 V) -0.4 0.3 VIO_SD V VHYS Input Hysteresis 100 mV VOH High Level Ouput Voltage 3.3 V operation (VIOSD = 3.3 V) VIOSD -0.4 V VHO Low Level Output Voltage 3.3 V operation (VIOSD = 3.3 V) 0.4 V For SDIO 3.0 standard modes SDR12, SDR25, SDR50, and DDR50, a supply voltage of VIOSD = 1.8 V should be used.

4.3.2 Current Consumption

The current consumption depends on the user scenario, the setup and timing of the power modes. Assume VDD2V2 = 2.2 V, VDD1V8 = 1.8 V, VIORF = 3.3 V, VIOSD = 3.3 V, VIO = 1.8 V, and Tamb = 25 °C, if nothing else stated. General Current Consumption Symbol Parameter Condition Min. Typ. Max. Units IVDD1V8 @ PDn Power Down Grounding of PDn pin 150 µA IVDD2V2 @ PDn 5 µA IVDD1V8 @ DeepSleep WLAN/ Bluetooth Deep Sleep Low-power state used in sleep state 600 µA IVDD2V2 @ DeepSleep 5 µA IVDD1V8 @ Firmware Init Firmware Initialization Device Initialization 400 mA IVDD2V2 @ Firmware Init 950 mA WLAN Current Consumption Symbol Parameter Condition Min. Typ. Max. Units IVDD1V8 @ TX Active Transmit13 PTX = +15 dBm for 5 GHz band 802.11a @ 54 Mbps 230 mA PTX = +14 dBm for 5 GHz band 802.11n 20M @ MCS7 240 mA 13 Peak values for specified output power level and data rate with UDP traffic between the AP and Device (STA).

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 50 Symbol Parameter Condition Min. Typ. Max. Units PTX = +13 dBm for 5 GHz band 802.11n 40M @ MCS7 250 mA PTX = +16 dBm for 2.4 GHz band 802.11b @ 11 Mbps 175 mA PTX = +15 dBm for 2.4 GHz band 802.11g @ 54 Mbps 180 mA PTX = +14 dBm for 2.4 GHz band 802.11n 20M @ MCS7 185 mA IVDD2V2 @ TX Active Transmit13 PTX = +15 dBm for 5 GHz band 802.11a @ 54 Mbps 180 mA PTX = +14 dBm for 5 GHz band 802.11n 20M @ MCS7 170 mA PTX = +13 dBm for 5 GHz band 802.11n 40M @ MCS7 160 mA PTX = +16 dBm for 2.4 GHz band 802.11b @ 11 Mbps 240 mA PTX = +15 dBm for 2.4 GHz band 802.11g @ 54 Mbps 190 mA PTX = +14 dBm for 2.4 GHz band 802.11n 20M @ MCS7 170 mA

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 51 Symbol Parameter Condition Min. Typ. Max. Units IVDD1V8 @ RX Active Receive14 5 GHz band 802.11a @ 54 Mbps 85 mA 5 GHz band 802.11n 20M @ MCS7 95 mA 5 GHz band 802.11n 40M @ MCS7 110 mA 2.4 GHz band 802.11b @ 11 Mbps 65 mA 2.4 GHz band 802.11g @ 54 Mbps 70 mA 2.4 GHz band 802.11n 20M @ MCS7 75 mA IVDD2V2 @ RX Active Receive14 5 GHz band 802.11a/n 20 µA 2.4 GHz band 802.11b/g/n 20 µA IVDD1V8 @ IEEE-PS IEEE Power Save15 DTIM = 1 with beacon interval 100 ms (Average16) 2 mA IVDD2V2 @ IEEE-PS 20 µA Bluetooth Current Consumption Symbol Parameter Condition Min. Typ. Max. Units IVDD1V8 @ TX BT SCO HV3 Peak, PTX = +4 dBm 55 mA BT ACL DH1 Average, PTX = 0 dBm 25 mA BT ACL 3-DH5 Average, PTX = 0 dBm 35 mA LE PTX = 0 dBm 45 mA IVDD2V2 @ TX BT SCO HV3 PTX = +4 dBm 15 µA BT ACL DH1 PTX = 0 dBm 15 µA BT ACL 3-DH5 PTX = 0 dBm 15 µA LE PTX = 0 dBm 15 µA IVDD1V8 @ RX LE Peak 30 mA IVDD2V2 @ RX LE 5 µA IVDD1V8 @ Page Scan BT Page Scan Peak 2.4 mA IVDD2V2 @ Page Scan 5 µA IVDD1V8 @ PI Scan BT Page and Inquiry Scan Peak 3.8 mA IVDD2V2 @ PI Scan 5 µA IVDD1V8 @ LE Advertise LE Advertise in 1.28s Interval Peak 1.5 mA IVDD2V2 @ LE Advertise 5 µA IVDD1V8 @ LE Scan LE Scan with Interval 1.28 s Peak 1.5 mA IVDD2V2 @ LE Scan 5 µA 14 Peak values for specified data rate with UDP traffic between the Device (Client) and AP (Server). The WLAN/Bluetooth combo Firmware is downloaded and Bluetooth is in Deep Sleep. 15 In IEEE Power Save the device automatically wakes up on beacons. If it is a DTIM value of 1 along with a beacon interval of 100 ms, the device wakes up every 100 ms. 16 The average current is averaged over one cycle which includes sleep time and wake up time.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 52 RF Control Current Consumption Symbol Parameter Condition Min. Typ. Max. Units IVIORF RF FE Control Controlled by Firmware 5 µA IRF_SW1/2 RF Switch Pin Controlled by VRF_SW1/2 (high level) 5 µA

4.3.3 Internal Operating Frequencies

Symbol Parameter Condition Min. Typ. Max. Units fSYSCLK1 CPU1/System /Encryption Clock Speed Refers to clock speed of SoC’s CPU1

160 MHz

fSYSCLK2 CPU2 Refers to clock speed of SoC’s CPU2

64 MHz

Frequency tolerance < ±10 ppm over operating temperature and process Frequency tolerance < ±20 ppm over operating temperature, aging and process, CMOS input clock signal type 32.768 kHz

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 53

4.3.4 Power-up Sequence

Symbol Parameter Min. Typ. Max. Units VDD2V2 Voltage level of VIOSD 100 % VDD1V8 Voltage level of VDD2V2 90 % PDn Voltage level of VDD2V2 90 %

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 54

4.3.5 Host Interface

4.3.5.1 SDIO Interface

The SDIO Interface pins are powered from the VIOSD voltage supply with either 3.3 V or 1.8 V. The SDIO electrical specifications are identical for the 1-bit and 4-bit SDIO modes. For the DC specification please refer to  4.3.1 Digital Pin Characteristics. SDIO Timing Data: Default and High-Speed Modes (VIOSD 3.3 V)17,18 Symbol Parameter Condition Min. Typ. Max. Units fPP Clock Frequency Normal 0 25 MHz High-speed 0 50 MHz TWL Clock Low Time Normal 10 ns High-speed 7 ns TWH Clock High Time Normal 10 ns High-speed 7 ns TISU Input Setup Time Normal 5 ns High-speed 6 ns TIH Input Hold Time Normal 5 ns High-speed 2 ns TODLY Output Delay Time Normal 14 ns CL  40 Pf (1 Card) High-speed 14 ns TOH Output Hold Time High-speed 2.5 ns 17 For SDIO 2.0 running at 50 MHz clock frequency, a supply voltage VIOSD of 1.8 V is recommended. 18 For SDIO 2.0 running at 25 MHz clock frequency, either 1.8 V or 3.3 V can be used.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 55 SDIO Protocol Timing Diagram: Default Speed Mode (VIOSD 3.3 V) SDIO Protocol Timing Diagram: High-Speed Mode (VIOSD 3.3 V)

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 56 SDIO Timing Data: SDR12, SDR25, SDR50 Modes (VIOSD 1.8 V) Symbol Parameter Condition Min. Typ. Max. Units fPP Clock Frequency SDR12/SDR25/ SDR50 25 100 MHz TIS Input Setup Time SDR12/SDR25/ SDR50 3 ns TIH Input Hold Time SDR12/SDR25/ SDR50 0.8 ns TCLK Clock Time SDR12/SDR25/ SDR50 10 40 ns TCR , TCF Rise Time, Fall Time TCR , TCF < 2 ns (max.) at CCARD = 10 pF SDR12/SDR25/ SDR50 0.2 * TCLK ns TODLY Output Delay Time CL  30 pF SDR12/SDR25/ SDR50 7.5 ns TOH Output Hold Time CL = 15 pF SDR12/SDR25/ SDR50 1.5 ns SDIO Protocol Timing Diagram: SDR12, SDR25, SDR50 Modes (VIOSD 1.8 V) SDIO Timing Data: DDR50 Mode (VIOSD 1.8 V) Symbol Parameter Condition Min. Typ. Max. Units Clock TCLK Clock Time 50 MHz (max.) Between Rising Edges DDR50 20 ns

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 57 Symbol Parameter Condition Min. Typ. Max. Units TCR, TCF Rise Time, Fall Time TCR, TCF < 4.00 ns (max.) at 50 MHz, CCARD = 10 pF DDR50 0.2 * TCLK ns Clock Duty DDR50 45 55 % CMD Input (referenced to clock rising edge) TIS Input Setup Time CCARD  10 pF (1 card) DDR50 6 ns TIH Input Hold Time CCARD  10 pF (1 card) DDR50 0.8 ns CMD Output (referenced to clock rising edge) TODLY Output Delay Time During Data Transfer Mode CL  30 pF (1 card) DDR50 13.7 ns TOHLD Output Hold Time CL ≥ 15 pF (1 card) DDR50 1.5 ns DAT[3:0] Input (referenced to clock rising and falling edge) TIS2x Input Setup Time CCARD  10 pF (1 card) DDR50 3 ns TIH2x Input Hold Time CCARD  10 pF (1 card) DDR50 0.8 ns DAT[3:0] Output (referenced to clock rising and falling edge) TODLY2x (max.) Output Delay Time During Data Transfer Mode CL  25 pF (1 card) DDR50 7 ns TODLY2x (min.) Output Hold Time CL ≥ 15 pF (1 card) DDR50 1.5 ns

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 58 SDIO CMD Timing Diagram: DDR50 Mode (VIOSD 1.8 V, 50 MHz) SDIO DAT[3:0] Timing Diagram: DDR50 Mode19 (VIOSD 1.8 V, 50 MHz) 19 In DDR50 mode, DAT[3:0] lines are sampled on both edges of the clock (not applicable for CMD line).

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 59

4.3.5.2 High-Speed UART Interface

The High-Speed UART Interface pins are powered from the VIO voltage supply with 1.8 V. For the DC specification please refer to  4.3.1 Digital Pin Characteristics. The UART interface operation includes:

• Support data input/output operations for peripheral devices connected through a standard UART interface
• 4-wire data transfer (RXD, TXD, RTS, CTS)
• Programmable baud rate (1 200 bps to 4 Mbps)
• Data format (LSB first)
• Data bit: 5 bit to 8 bit
• Parity bit: 0 bit to 4 bit
• Stop bit: 1 bit to 2 bit Interface Signals Pin No. Signal Name Specification Name Type Description F3 UART_SOUT TXD Host Controller Interface (HCI) Transmit data output F4 UART_SIN RXD Receive data input F5 UART_RTS RTS Request to send (active low) G5 UART_CTS CTS Clear to send (active low)

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 60 Interface Transport Settings Item Range Default Comment Baudrate 1 200 ~ 4 000 000 3 000 000 Baud Data Bits 5 ~ 8 8 LSB first Parity Bits 0 ~ 4 0 Stop Bit 1/1.5/2 1 Supported Baud Rates Baud 1 200 2 400 4 800 9 600 19 200 38 400 57 600 76 800 115 200 230 400 460 800 500 000 921 600 1 000 000 1 382 400 1 500 000 1 843 200 2 000 000 2 100 000 2 764 800 3 000 000 3 250 000 3 692 300 4 000 000 UART Timing Diagram

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 61

4.3.6 Peripheral Interface

The Peripheral Interface pins are powered from the VIO voltage supply with 1.8 V. For the DC specification please refer to  4.3.1 Digital Pin Characteristics.

4.3.6.1 GPIO Interface

The General-Purpose I/O (GPIO) interface is used to implement user-defined input and output signals to and from the device, such as external interrupts and other user-defined I/Os. Configurable GPIOs Function GPIO Pin Name IO0 IO1 IO2 IO3 IO12 IO13 IO14 IO15 GPIO IN YES YES YES YES YES YES YES YES GPIO OUT YES YES YES YES YES YES YES YES IRQ IN YES YES YES YES YES YES YES YES LED Mode Symbol Parameter Condition Typ. Units IOH Switching Current High Tristate on pin (requires pull-up) Tristate when driving high mA IOL Switching Current Low @ 0.4 V 10 mA

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 62

4.3.7 Audio Interface

4.3.7.1 PCM Interface

Pin No. Signal Name Specification Name Type Description A1 PCM_DOUT DOUT Output PCM data B1 PCM_CLK CLK Input/Output PCM clock signal, output if PCM master, input if PCM slave B1 PCM_MCLK MCLK Output PCM clock signal (optional), optional clock used for some codecs, derived from PCM_CLK B2 PCM_DIN DIN Input PCM data B3 PCM_SYNC SYNC Input/Output PCM Sync pulse signal, output if PCM master, input if PCM slave Modes of Operation The PCM Interface supports two modes of operation:

• PCM master
• PCM slave When in PCM master mode, the interface generates a 2 MHz or a 2.048 MHz signal PCM_CLK and a 8 kHz signal PCM_SYNC signal. An alternative PCM master mode is available that uses an externally generated signal PCM_CLK, but still generates the 8 kHz signal PCM_SYNC. The external signal PCM_CLK must have a frequency that is an integer multiple of 8 kHz. Supported frequencies are in the 512 kHz to 4 MHz range. When in PCM slave mode, the interface has both signal PCM_CLK and signal PCM_SYNC as inputs, thereby letting another unit on the PCM bus generate the signals. The PCM interface consists of up to four PCM slots (time-devided) preceded by a PCM sync signal. Each PCM slot can be either 8 bits or 16 bits wide. The slots can be separated in time, but they are not required to follow immediately after another. The timing is relative to signal PCM_SYNC.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 63 PCM Timing Data: Master Mode Symbol Min. Typ. Max. Units FBCLK 2/2.048 MHz Duty CycleBCLK 0.4 0.5 0.6 TBCLK rise/fall 3 ns TDO 15 ns TDISU 20 ns TDIHO 15 ns TBF 15 ns PCM Timing Diagram: Master Mode CLK DOUT DIN SYNC TBF TTDO TBCLK TDISU TDIHO

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 64 PCM Timing Data: Slave Mode Symbol Min. Typ. Max. Units FBCLK 2/2.048 MHz Duty CycleBCLK 0.4 0.5 0.6 TBCLK rise/fall 3 ns TDO 30 ns TDISU 15 ns TDIHO 10 ns TBFSU 15 ns TBFHO 10 ns PCM Timing Diagram: Slave Mode CLK DOUT DIN SYNC TBFSU TTDO TBCLK TDISU TDIHO TBFHO

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 65

4.3.8 Coexistence Interface

The Coexistence Interface pins are powered from the VIO voltage supply with 1.8 V. For the DC specification please refer to  4.3.1 Digital Pin Characteristics.

4.4 RF Electrical Characteristics

4.4.1 WLAN Radio Specification

Parameter Condition Min. Typ. Max. Units RF Frequency Range 2.4 GHz: IEEE 802.11b/g/n 2 400 2 483.5 MHz 5 GHz: IEEE 802.11a/n 4 900 5 925 MHz Transmit Mode Parameter Condition Min. Typ. Max. Units RF Frequency Range 2.4 GHz: IEEE 802.11b/g/n 2 400 2 483.5 MHz 5 GHz: IEEE 802.11a/n 4 900 5 925 MHz

4.4.2 WLAN RF Characteristics

4.4.2.1 RF Characteristics for IEEE 802.11b and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 2 400 2 483.5 MHz Carrier Frequency Tolerance -25 25 ppm Transmit Output Power 16 dBm Spectrum Mask fC ± 11 MHz -30 dBr fC ± 22 MHz -50 Power-on/Power-down Ramp 2 µs RF Carrier Suppression -15 dB Error Vector Magnitude (EVM) Peak 35 %

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 66 Parameter Condition Min. Typ. Max. Units Minimum Receive Sensitivity 1 Mbps (DSSS) FER ≤ 8 % -98 dBm

2 Mbps (DSSS) FER ≤ 8 % -93 -80 dBm

5.5 Mbps (CCK) FER ≤ 8 % -91 dBm

11 Mbps (CCK) FER ≤ 8 % -89 -76 dBm

Maximum Input Level FER ≤ 8 % -10 dBm Adjacent Channel Rejection FER ≤ 8 % 35 dB 4.4.2.2 RF Characteristics for IEEE 802.11g and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 2 400 2 483.5 MHz Carrier Frequency Tolerance -25 25 ppm Transmit Output Power 6 Mbps to 36 Mbps +16 dBm

48 Mbps to 54 Mbps +15 dBm

Spectrum Mask fC ± 11 MHz -20 dBr fC ± 20 MHz -28 dBr fC ± 30 MHz -40 dBr Transmitter Center Frequency Leakage -15 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (6 Mbps) -5 dB BPSK, CR 3/4 (9 Mbps) -8 dB QPSK, CR 1/2 (12 Mbps) -10 dB QPSK, CR 3/4 (18 Mbps) -13 dB 16-QAM, CR 1/2 (24 Mbps) -16 dB 16-QAM, CR 3/4 (36 Mbps) -19 dB 64-QAM, CR 2/3 (48 Mbps) -22 dB 64-QAM, CR 3/4 (54 Mbps) -25 dB Minimum Receive Sensitivity BPSK, CR 1/2 (6 Mbps) PER ≤ 10 % -91 -82 dBm BPSK, CR 3/4 (9 Mbps) PER ≤ 10 % -90 -81 dBm QPSK, CR 1/2 (12 Mbps) PER ≤ 10 % -89 -79 dBm QPSK, CR 3/4 (18 Mbps) PER ≤ 10 % -87 -77 dBm 16-QAM, CR 1/2 (24 Mbps) PER ≤ 10 % -84 -74 dBm 16-QAM, CR 3/4 (36 Mbps) PER ≤ 10 % -81 -70 dBm 64-QAM, CR 2/3 (48 Mbps) PER ≤ 10 % -77 -66 dBm

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 67 Parameter Condition Min. Typ. Max. Units 64-QAM, CR 3/4 (54 Mbps) PER ≤ 10 % -76 -65 dBm Maximum Input Level PER ≤ 10 % -20 dBm Adjacent Channel Rejection BPSK, CR 1/2 (6 Mbps) PER ≤ 10 % 16 dB 64-QAM, CR 3/4 (54 Mbps) PER ≤ 10 % -1 dB and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 2.4 GHz 2 400 2 483.5 MHz Carrier Frequency Tolerance -25 25 ppm Transmit Output Power MCS0 to MCS2 +15 dBm MCS3 to MCS4 +15 dBm MCS5 to MCS7 +14 dBm Spectrum Mask fC ± 11 MHz -20 dBr fC ± 20 MHz -28 dBr fC ± 30 MHz -45 dBr Transmitter Center Frequency Leakage -15 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Minimum Receive Sensitivity20

6.5 Mbps (MCS0) PER ≤ 10 % -90 -82 dBm

13 Mbps (MCS1) PER ≤ 10 % -88 -79 dBm

19.5 Mbps (MCS2) PER ≤ 10 % -86 -77 dBm

26 Mbps (MCS3) PER ≤ 10 % -83 -74 dBm

39 Mbps (MCS4) PER ≤ 10 % -80 -70 dBm

20 The Minimum Sensitivity levels apply only to non-STBC modes, MCS 0~7, 800 ns LGI, and BCC.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 68 Parameter Condition Min. Typ. Max. Units

52 Mbps (MCS5) PER ≤ 10 % -76 -66 dBm

58.5 Mbps (MCS6) PER ≤ 10 % -74 -65 dBm

65 Mbps (MCS7) PER ≤ 10 % -73 -64 dBm

Maximum Input Level PER ≤ 10 % -20 dBm Adjacent Channel Rejection21 65 Mbps (MCS7) PER ≤ 10 % -2 dB 21 The Adjacent Channel Rejection levels apply only to non -STBC modes, MCS 0~7, 800 ns LGI, and BCC.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 69 and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 2.4 GHz 2 400 2 483.5 MHz Carrier Frequency Tolerance -25 +25 ppm Transmit Output Power MCS0 to MCS2 +14 dBm MCS3 to MCS4 +14 dBm MCS5 to MCS7 +13 dBm Spectrum Mask fC ± 21 MHz -20 dBr fC ± 40 MHz -28 dBr fC ± 60 MHz -45 dBr Transmitter Center Frequency Leakage -20 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Minimum Receive Sensitivity20 13.5 Mbps (MCS0) PER ≤ 10 % -86 -79 dBm

27 Mbps (MCS1) PER ≤ 10 % -85 -76 dBm

40.5 Mbps (MCS2) PER ≤ 10 % -83 -74 dBm

54 Mbps (MCS3) PER ≤ 10 % -80 -71 dBm

81 Mbps (MCS4) PER ≤ 10 % -77 -67 dBm

108 Mbps (MCS5) PER ≤ 10 % -73 -63 dBm

121.5 Mbps (MCS6) PER ≤ 10 % -71 -62 dBm

135 Mbps (MCS7) PER ≤ 10 % -69 -61 dBm

Maximum Input Level PER ≤ 10 % -20 dBm Adjacent Channel Rejection21 135 Mbps (MCS7) PER ≤ 10 % -2 dB

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 70 4.4.2.5 RF Characteristics for IEEE 802.11n (BW 20 MHz, 5 GHz) and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 5 GHz U-NII-1 5 150 5 250 MHz

5 GHz U-NII-2A 5 250 5 350 MHz

5 GHz U-NII-2C 5 470 5 725 MHz

5 GHz U-NII-3 5 725 5 825 MHz

Carrier Frequency Tolerance -20 20 ppm Transmit Output Power MCS0 to MCS2 +15 dBm MCS3 to MCS4 +15 dBm MCS5 to MCS7 +14 dBm Spectrum Mask fC ± 11 MHz -20 dBr fC ± 20 MHz -28 dBr fC ± 30 MHz -40 dBr Transmitter Center Frequency Leakage -15 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Minimum Receive Sensitivity20

6.5 Mbps (MCS0) PER ≤ 10 % -89 -82 dBm

19.5 Mbps (MCS2) PER ≤ 10 % -85 -77 dBm

26 Mbps (MCS3) PER ≤ 10 % -82 -74 dBm

39 Mbps (MCS4) PER ≤ 10 % -79 -70 dBm

52 Mbps (MCS5) PER ≤ 10 % -74 -66 dBm

58.5 Mbps (MCS6) PER ≤ 10 % -73 -65 dBm

65 Mbps (MCS7) PER ≤ 10 % -71 -64 dBm

Maximum Input Level PER ≤ 10 % -30 dBm Adjacent Channel Rejection21 65 Mbps (MCS7) PER ≤ 10 % -2 dB

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 71 4.4.2.6 RF Characteristics for IEEE 802.11n (BW 40 MHz, 5 GHz) and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 5 GHz U-NII-1 5 150 5 250 MHz Carrier Frequency Tolerance -20 20 ppm Transmit Output Power MCS0 to MCS2 +14 dBm MCS3 to MCS4 +14 dBm MCS5 to MCS7 +13 dBm Spectrum Mask fC ± 21 MHz -20 dBr fC ± 40 MHz -28 dBr fC ± 60 MHz -40 dBr Transmitter Center Frequency Leakage -20 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (MCS0) -5 dB QPSK, CR 1/2 (MCS1) -10 dB QPSK, CR 3/4 (MCS2) -13 dB 16-QAM, CR 1/2 (MCS3) -16 dB 16-QAM, CR 3/4 (MCS4) -19 dB 64-QAM, CR 2/3 (MCS5) -22 dB 64-QAM, CR 3/4 (MCS6) -25 dB 64-QAM, CR 5/6 (MCS7) -27 dB Minimum Receive Sensitivity20 13.5 Mbps (MCS0) PER ≤ 10 % -86 -79 dBm

40.5 Mbps (MCS2) PER ≤ 10 % -82 -74 dBm

54 Mbps (MCS3) PER ≤ 10 % -79 -71 dBm

81 Mbps (MCS4) PER ≤ 10 % -76 -67 dBm

108 Mbps (MCS5) PER ≤ 10 % -72 -63 dBm

121.5 Mbps (MCS6) PER ≤ 10 % -70 -62 dBm

Maximum Input Level PER ≤ 10 % -30 dBm Adjacent Channel Rejection21 135 Mbps (MCS7) PER ≤ 10 % -2 dB

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 72 4.4.2.7 RF Characteristics for IEEE 802.11a and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector. Parameter Condition Min. Typ. Max. Units RF Frequency Range 5 GHz U-NII-1 5 150 5 250 MHz Carrier Frequency Tolerance -20 20 ppm Transmit Output Power

6 Mbps to 36 Mbps +16 dBm

fC ± 11 MHz -20 dBr fC ± 20 MHz -28 dBr fC ± 30 MHz -40 dBr Transmitter Center Frequency Leakage -15 dB Transmitter Spectral Flatness -4 4 dB Constellation Error (EVM) BPSK, CR 1/2 (6 Mbps) -5 dB BPSK, CR 3/4 (9 Mbps) -8 dB QPSK, CR 1/2 (12 Mbps) -10 dB QPSK, CR 3/4 (18 Mbps) -13 dB 16-QAM, CR 1/2 (24 Mbps) -16 dB 16-QAM, CR 3/4 (36 Mbps) -19 dB 64-QAM, CR 2/3 (48 Mbps) -22 dB 64-QAM, CR 3/4 (54 Mbps) -25 dB Minimum Receive Sensitivity BPSK, CR 1/2 (6 Mbps) PER ≤ 10 % -90 -82 dBm BPSK, CR 3/4 (9 Mbps) PER ≤ 10 % -90 -81 dBm QPSK, CR 1/2 (12 Mbps) PER ≤ 10 % -89 -79 dBm QPSK, CR 3/4 (18 Mbps) PER ≤ 10 % -86 -77 dBm 16-QAM, CR 1/2 (24 Mbps) PER ≤ 10 % -84 -74 dBm 16-QAM, CR 3/4 (36 Mbps) PER ≤ 10 % -80 -70 dBm 64-QAM, CR 2/3 (48 Mbps) PER ≤ 10 % -76 -66 dBm 64-QAM, CR 3/4 (54 Mbps) PER ≤ 10 % -75 -65 dBm Maximum Input Level PER ≤ 10 % -30 dBm Adjacent Channel Rejection BPSK, CR 1/2 (6 Mbps) PER ≤ 10 % 16 dB 64-QAM, CR 3/4 (54 Mbps) PER ≤ 10 % -1 dB

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 73

4.4.3 Bluetooth RF Characteristics

and Tamb = 25 °C, if nothing else stated. 50  terminal load connected to the RF connector.

4.4.3.1 Receiver Section RF Characteristics

Parameter Condition Min. Typ. Max. Units RF Frequency Range 2 400 2 483.5 MHz Interference Performance (Basic Rate) C/I Ratio GFSK RSL = -67 dBm BER ≤ 0.1 % C/I (Co-channel) 11 dB C/I (1 MHz) 0 dB C/I (2 MHz) -30 dB C/I (3 MHz) -40 dB C/I (Image) -9 dB C/I (Image ± 1 MHz) -20 dB Interference Performance (Enhanced Data Rate) C/I Ratio π/4-DQPSK RSL = -67 dBm BER ≤ 0.01 % C/I (Co-channel) 13 dB C/I (1 MHz) 0 dB C/I (2 MHz) -30 dB C/I (3 MHz) -40 dB C/I (Image) -7 dB C/I (Image ± 1 MHz) -20 dB 8-DPSK RSL = -67 dBm BER ≤ 0.01 % C/I (Co-channel) 21 dB C/I (1 MHz) 5 dB C/I (2 MHz) -25 dB C/I (3 MHz) -33 dB C/I (Image) 0 dB C/I (Image ± 1 MHz) -13 dB Interference Performance (Low Energy) C/I Ratio GFSK RSL = -67 dBm BER ≤ 0.1 % C/I (Co-channel) 21 dB C/I (1 MHz) 15 dB C/I (2 MHz) -17 dB C/I (3 MHz) -27 dB C/I (Image) -9 dB C/I (Image ± 1 MHz) -15 dB Minimum Receive Sensitivity BR, DH1 BER ≤ 0.1 % -94 -70 dBm EDR, 2DH1 BER ≤ 0.01 % -90 -70 dBm LE, GFSK BER ≤ 0.1 % -90 -70 dBm

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 74 Parameter Condition Min. Typ. Max. Units Out-of-band Blocking (Basic Rate) Interfering Signal Power GFSK RSL = -67 dBm BER ≤ 0.1 %

30 MHz: 2 000 MHz -10 dBm

2 GHz: 2.399 GHz -27 dBm

2.484 GHz: 3 GHz -27 dBm

3 GHz: 12.75 GHz -10 dBm Out-of-band Blocking (Low Energy) Interfering Signal Power GFSK RSL = -67 dBm BER ≤ 0.1 %

30 MHz: 2 000 MHz -30 dBm

2.003 GHz: 2.399 GHz -35 dBm 2.484 GHz: 2.997 GHz -35 dBm 3 GHz: 12.75 GHz -30 dBm RSSI Range Resolution = 1 dB -90 0 dBm

4.4.3.2 Transmitter Section RF Characteristics

Parameter Condition Min. Typ. Max. Units RF Frequency Range 2 400 2 483.5 MHz Maximum Output Power Basic Rate (BR) +8 dBm Enhanced Data Rate (EDR) +6 dBm Low Energy (LE) +6 dBm Gain Range Gain control 30 dB Gain Resolution 0.5 dB Spurious Emission (BR) (in-band) ± 500 kHz -20 dBc ± 2 MHz, |M-N| = 2 -20 dBm ± 3 MHz or greater, |M-N| ≥ 3 -40 dBm Spurious Emission (EDR) (in-band) ± 1 MHz -26 dBc ± 1.5 MHz -20 dBm ± 2.5 MHz -40 dBm Spurious Emission (LE) (in-band)

1 Mbps ± 2 MHz, |M-N| = 2 -20 dBm

± 3 MHz or greater, |M-N| ≥ 3 -30 dBm

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 75

4.5 Reliability Tests

The measurement should be done after the test device has been exposed to room temperature and humidity for one hour. No. Item Limit Condition

1 Vibration test Electrical parameter should be in

Freq.: 10 Hz~50 Hz; Amplitude: 1.5 mm; 20 min./cycle, 1 h each of XYZ axis

2 Shock test See above Dropped 3 times onto hard wood from a

3 Heat cycle test See above -40 °C for 30 min. and 85 °C for 30 min.; each temperature 300 cycles

4 Moisture test See above 60 °C, 90 % RH, 300 h

5 Low temp. test See above -40 °C, 300 h 6 High temp. test See above 85 °C, 300 h

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 76

4.6 Recommended Soldering Profile

• Reflow permissible cycle: 2
• Opposite side reflow is prohibited due to module weight
• More than 75 percent of the soldering area shall be coated by solder
• The soldering profiles should be adhered to in order to prevent electrical or mechanical damage
• Soldering profile assumes lead-free soldering

 PAN9026 Wi-Fi/Bluetooth Module

5 Cautions

Product Specification Rev. 1.2 Page 77 Failure to follow the guidelines set forth in this document may result in degrading of the module functions and damage to the module.

5.1 Design Notes

Radio requires a RF ground plane on the rest of the Printed Circuit Board (PCB) area. This can be located on any layer of the PCB. For best performance, extend the RF ground plane the entire length of your board. Connect all ground pins and do not notch the ground plane around the module. The bottom of the module is grounded. So be careful of vias or conductive traces located under the modules that are not soldered masked to prevent shorting. Keep metallic components, connectors, copper traces, internal layers, and ground planes away from the antenna area in 3D space! 1. Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). 3. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module). 4. This module should not be mechanically stressed when installed. 5. Keep this module away from heat. Heat is the major cause of decreasing the life time of these modules. 6. Avoid assembly and use of the target equipment in conditions where the module temperature may exceed the maximum tolerance. 7. Keep this module away from other high frequency circuits. 8. Refer to the recommended pattern when designing a board.

5.2 Installation Notes

1. Reflow soldering is possible twice based on the conditions set forth in  4.6 Recommended Soldering Profile. Set up the temperature at the soldering portion of this module according to this reflow profile. 2. Carefully position the module so that the heat will not burn into printed circuit boards or affect other components that are susceptible to heat. 3. Carefully locate the module, to avoid an increased temperature caused by heat generated by neighboring components.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 78 4. If a vinyl-covered wire comes into contact with the module, the wire cover will melt and generate toxic gas, damaging the insulation. Never allow contact between a vinyl cover and these modules to occur. 5. This module should not be mechanically stressed or vibrated when reflowed. 6. To repair the board by hand soldering, follow the conditions set forth in this chapter. 7. Do not wash this product. 8. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the module.

5.3 Usage Condition Notes

1. Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2. Do not use dropped modules. 3. Do not touch, damage, or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this module. 5. Electrode peeling strength: Do not apply a force of more than 4.9 N in any direction on the soldered module. 6. Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. 7. These modules are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information, and communication equipment.

5.4 Storage Notes

1. The module should not be stressed mechanically during storage. 2. Do not store these modules in the following conditions or the performance characteristics of the module, such as RF performance will be adversely affected: – Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX, – Storage in direct sunlight, – Storage in an environment where the temperature may be outside the range of 5 °C to 35 °C, or where the humidity may be outside the 45 % to 85 % range, – Storage of the modules for more than one year after the date of delivery storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. 3. Keep this module away from water, poisonous gas, and corrosive gas. 4. This module should not be stressed or shocked when transported.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 79 5. Follow the specification when stacking packed crates (max. 10).

5.5 Safety Cautions

These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, provide the following failsafe functions as a minimum: 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status.

5.6 Other Cautions

1. Do not use the module for other purposes than those listed in section  5.3 Usage Condition Notes 2. Be sure to provide an appropriate fail-safe function on your product to prevent any additional damage that may be caused by the abnormal function or the failure of the module. 3. This module has been manufactured without any ozone chemical controlled under the Montreal Protocol. 4. These modules are not intended for use under the special conditions shown below. Before using these modules under such special conditions, carefully check their performance and reliability under the said special conditions to determine whether or not they can be used in such a manner: – In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash, – In direct sunlight, outdoors, or in a dusty environment, – In an environment where condensation occurs, – In an environment with a high concentration of harmful gas (e.g. salty air, HCl, Cl2, SO2, H2S, NH3, and NOX). 5. If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these modules with new modules, because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. Please refer to the Panasonic website for for further information  7.2.2 Product Information.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 80

5.7 Restricted Use

5.7.1 Life Support Policy

This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to r esult in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting.

5.7.2 Restricted End Use

This Panasonic Industrial Devices Europe GmbH product is not designed for any restricted activity that supports the development, production, handling usage, maintenance, storage, inventory or proliferation of any weapons or military use. Transfer, export, re-export, usage or reselling of this product to any destination, end-user or any end-use prohibited by the European Union, United States or any other applicab le law is strictly prohibited.

 PAN9026 Wi-Fi/Bluetooth Module

6 Regulatory and Certification Information

Product Specification Rev. 1.2 Page 81

6.1 Federal Communications Commission (FCC) for US

6.1.1 FCC Notice

The PAN9026, including the ceramic antenna (ENWF9201A1EF and ENWF9208A1EF), and the antennas, which are listed in  6.1.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. The FCC identifier for ENWF9201A1EF is FCC ID: T7V-9026. The FCC identifier for ENWF9208A1EF is FCC ID: T7V-9026.

6.1.2 Caution

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 82 It is recommended to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

6.1.3 Label Requirements

The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label (laser marking) on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier for model ENWF9201A1EF is FCC ID: T7V-9026. The FCC identifier for model ENWF9208A1EF is FCC ID: T7V-9026. This FCC identifier is valid for the PAN9026. The end product must in any case be labelled on the exterior with: “Contains FCC ID: T7V-9026”.

6.1.4 Antenna Warning

This antenna warning refers to the test device with the model number ENWF9201A1EF and ENWF9208A1EF in bottom pad mode  RF-Switch Pins Function. The device is tested with a standard SMA connector and with the antenna listed b elow. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in  6.1.5 Approved Antenna List is the same (FCC ID: T7V-9026).

6.1.5 Approved Antenna List

Item Part Number Manufacturer Type Polarization Frequency Band Gain (dBi) Min Peak

1 ANT162442DT-

Linear 2.400 - 2.484 GHz -36 2.1 5.150 - 5.850 GHz -42 1.5

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 83

6.1.6 RF Exposure

To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed  6.1.5 Approved Antenna List. The preceding statement must be included as a caution statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of the PAN9026 with a mounted ceramic chip antenna (FCC ID: T7V-9026 for model ENWF9201A1EF and ENWF9208A1EF) are fulfilled for mobile configuration. The installation of the module is restricted to mobile host devices. The PAN9026 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance.

6.1.7 Integration Instructions

This chapter gives integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01. Section Topic and Comment

2.2 List of applicable FCC rules

47 CFR Section Part 15C

Frequency Band (MHz) 2 400 to 2 483.5 Systems Digital Transmission Systems operating within the 2 400 - 2 483.5 MHz Band Complied Module M/N ENWF9201A1EF, ENWF9208A1EF Frequency Band (MHz) 2 400 to 2 483.5 Systems Frequency Hopping Systems operating within the 2 400 - 2 483.5 MHz Band Complied Module M/N ENWF9201A1EF, ENWF9208A1EF

47 CFR Section Part 15E

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 84 Systems Unlicensed National Information Infrastructure Devices in the 5 GHz Bands Reference Method KDB 905462 D02 v02 Reference / Requirement 15E.407(h)(2) Complied Module M/N ENWF9201A1EF

2.3 Summarize the specific operational use conditions

Please refer to sections  5 Cautions, 5.3 Usage Condition Notes, and 6.1.5 Approved Antenna List.

2.4 Limited module procedures

Not applicable, the module has a single-modular transmitter approval.

2.5 Trace antenna designs

Not applicable, the module has a ceramic chip antenna. For guidance regarding the PCB layout requirements for module integration refer to the Design Guide  7.2.2 Product Information.

2.6 RF exposure considerations

Mobile application, the end customer has to assure that the device has a distance of more than 20 cm from the human body under all circumstances.

2.7 Antennas

2.8 Label and compliance information

Please refer to section  6.1.3 Label Requirements.

2.9 Information on test modes and additional testing requirements

The documents for integration guidance and compliance testing are available here  7.2.2 Product Information.

2.10 Additional testing, Part 15 Subpart B disclaimer

The single-modular transmitter is FCC authorized for the specific rule parts listed at section  List of applicable FCC rules. The host product manufacturer needs to also consider the FCC requirements for certified modular transmitter being used in the host product and maintain documentation on how the host product with the certified modular transmitter complies with the FCC rules. Host product manufacturers are responsible to follow the integration guidance and to perform a limited set of transmitter module verification testing, to ensure the end product is in compliance with the FCC rules. Also host product manufacturers are responsible for all additional equipment authorization and testing for technical requirements not covered by the module grant (e.g., unintentional radiator Part 15 Subpart B requirements, or transmitters used in the host that are not certified modules).

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 85

6.2 Innovation, Science, and Economic Development (ISED) for

PAN9026 and versions are licensed to meet the regulatory requirements of ISED. License for M/N: ENWF9203A1EF: IC: 216Q-9026 License for M/N: ENWF9208A1EF: IC: 216Q-9026 Manufacturers of mobile, fixed, or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in  6.1.5 Approved Antenna List, having a maximum gain of 2.1 dBi for 2.4 GHz and 1.5 dBi for 5 GHz. Antennas not included in this list or having a gain greater than 2.1 dBi for 2.4 GHz and 1.5 dBi for 5 GHz are strictly prohibited for use with this device. The required antenna impedance is 50 Ω. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. French PAN9026 (et ses versions) est garanti conforme aux dispositions règlementaires d’Innovation, Sciences et Développement économique (ISDE). Licence pour M/N: ENWF9203A1EF: IC: 216Q-9026 Licence pour M/N: ENWF9208A1EF: IC: 216Q-9026 Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement a ux limites d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé. Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau  6.1.5 Approved Antenna List, présentant un gain maximum de 2.1 dBi pour 2.4 GHz et 1.5 dBi pour 5 GHz. Des antennes autres que celles listées ici, ou présentant un gain supérieur à 2.1 dBi pour 2.4 GHz et 1.5 dBi pour 5 GHz ne doivent en aucune circonstance être utilises en combinaison avec ce produit. L’impédance des antennes compatibles est 50 Ω. L’antenne utilisée avec ce produit ne doit ni être située à proximité d’une autre antenne ou d’un autre émetteur, ni être utilisée conjointement avec une autre antenne ou un autre émetteur.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 86

6.2.1 Radio Standards Specification RSS-247 Issue 2

The Radio Standards Specification RSS-247, Issue 2, Digital Transmission Systems (DTSs), Frequency Hopping Systems (FHSs) and License-Exempt Local Area Network (LE-LAN) Devices, replaces RSS-247, Issue 1, dated May 2015. It sets out certification requirements for radio apparatus operating in the bands 2 400 MHz to 2 483.5 MHz and 5 725 MHz to 5 850 MHz employing frequency hopping, digital modulation and/or a combination (hybrid) of both techniques. It also includes license exempt local area network (LE-LAN) devices operating in the bands 5 150 MHz to 5 250 MHz, 5 250 MHz to 5 350 MHz, 5 470 MHz to 5 725 MHz and 5 725 MHz to 5 850 MHz as specified in SP-5 150 MHz.

6.2.1.1 General

Equipment covered by the standard RSS-247 is classified as Category I equipment. Either a technical acceptance certificate (TAC) issued by the Certification and Engineering Bureau of Innovation, Science and Economic Development Canada (ISED) or a certificate issued by a certification body (CB) is required.

6.2.1.2 Certification Requirements

RSS-247 shall be used in conjunction with RSS-Gen, General Requirements for Compliance of Radio Apparatus, for general specifications and information relevant to the equipment for which this standard applies. Equipment certified under the standard is required to comply with the provisions in RSS‑Gen with respect to emissions falling within restricted frequency bands. These restricted frequency bands are listed in RSS‑Gen.

6.2.1.3 Measurement Method

In addition to the requirements in RSS-Gen and the requirements of the standard RSS-247, the method for measuring DTS devices is provided in ANSI C63.10. 6.2.1.4 FHS and DTS operating in the bands 2 400 MHz to 2 483.5 MHz This section applies to frequency hopping systems (FHSs) in the bands 2 400 MHz to 2 483.5 MHz and 5 725 MHz to 5 850 MHz and digital transmission systems (DTSs) in the band 2 400 MHz to 2 483.5 MHz. Systems in these bands can be frequency hopping, digital transmission and/or a combination (hybrid) of both types. The digital transmission technology of DTSs or hybrid systems operating in the band 5 725 MHz to 5 850 MHz shall comply with the requirement in section Technical requirements for license-exempt local area network devices and digital transmission systems operating in the 5 GHz band.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 87 RSS-247 Section 5.1 Frequency Band (MHz) 2 400 to 2 483.5 Systems Frequency Hopping Systems Systems out of Scope FHS operating in the band 5 725 MHz to 5 850 MHz Fixed point-to-point systems Requirements The maximum peak conducted output power shall not exceed W if the hopset uses 75 or more hopping channels; the maximum peak conducted output power shall not exceed 0.125 W if the hopset uses less than 75 hopping channels. Complied Module M/N ENWF9203A1EF, ENWF9208A1EF RSS-247 Section 5.2 Frequency Band (MHz) 2 400 to 2 483.5 Systems Digital Transmission Systems Systems out of Scope - Requirements The minimum 6 dB bandwidth shall be 500 kHz. The transmitter power spectral density conducted from the transmitter to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. shall not exceed 4 W. Complied Module M/N ENWF9203A1EF, ENWF9208A1EF RSS-247 Section 5.3 Frequency Band (MHz) 2 400 to 2 483.5 Systems Hybrid Systems Systems out of Scope Hybrid devices operating in the band 5 725 MHz to 5 850 MHz. Requirements With the digital transmission operation of the hybrid system turned off, the frequency hopping operation shall have an average time of occupancy on any frequency not exceeding 0.4 seconds within a duration in seconds equal to the number of hopping frequencies multiplied by 0.4. With the frequency hopping turned off, the digital transmission operation shall comply with the power spectral density requirements for digital modulation systems set out in section “5.2”  RSS-247 Section. Complied Module M/N ENWF9203A1EF, ENWF9208A1EF

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 88 RSS-247 Section 5.4 Frequency Band (MHz) 2 400 to 2 483.5 Systems FHSs operating in the band 2 400 to 2 483.5 MHz. DTSs employing digital modulation techniques operating in the band 2 400 MHz to 2 483.5 MHz. Systems out of Scope FHSs operating in the band 902 MHz to 928 MHz and 5 725 MHz to 5 850 MHz. DTSs employing digital modulation techniques operating in the bands 902 MHz to 928 MHz. Fixed point-to-point systems in the bands 2 400 MHz to 2 483.5 MHz and 5 725 MHz to 5 850 MHz. Transmitters operating in the band 2 400 MHz to 2 483.5 MHz, may employ antenna systems that emit multiple directional beams simultaneously or sequentially. Requirements Transmitter Output Power: The maximum peak conducted output power shall not exceed 1 W if the hopset uses 75 or more hopping channels; the maximum peak conducted output power shall not exceed 0.125 W if the hopset uses less than 75 For DTSs employing digital modulation techniques operating in the band 2 400 MHz to 2 483.5 MHz, the maximum peak conducted output power shall Complied Module M/N ENWF9203A1EF, ENWF9208A1EF RSS-247 Section 5.5 Frequency Band (MHz) 2 400 to 2 483.5 System In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating … System out of Scope - Requirements Unwanted Emissions: In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root- mean-square averaging over a time interval the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general field strength limits specified in RSS-Gen is not required. Complied Module M/N ENWF9203A1EF, ENWF9208A1EF

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 89

6.2.1.5 Requirements for LE-LAN and DTS operating in the 5 GHz Band

The section provides standards for Licence-Exempt Local Area Network (LE-LAN) devices operating in the bands:

• 5 150 to 5 250 MHz,
• 5 250 to 5 350 MHz,
• 5 470 to 5 600 MHz,
• 5 650 to 5 725 MHz,
• 5 725 to 5 850 MHz
• For DTSs operating in the band 5 725 MHz to 5 850 MHz that employ digital modulation technology, but are not designed for LE-LAN operation. Devices with occupied bandwidths which overlap different bands shall comply with all operational requirements for each band. RSS-247 Section 6.2.1 Frequency Band (MHz) 5 150 to 5 250 Device Type LE-LAN devices are restricted to indoor operation only. Devices out of Scope OEM devices installed in vehicles. Power Limits Maximum e.i.r.p. shall not exceed 200 mW or 10+10 log10B, dBm, whichever spectral density shall not exceed 10 dBm in any 1 MHz band. Unwanted Emission Limits For transmitters with operating frequencies in the band 5 150 MHz to 5 250 MHz, all emissions outside the band 5 150 MHz to 5 350 MHz shall not exceed -27 dBm/MHz e.i.r.p. Any unwanted emissions that fall into the band 5 250 MHz to 5 350 MHz shall be attenuated below the channel power by at least 26 dB, when measured using a resolution bandwidth between 1 % and 5 % of the occupied bandwidth (i.e. 99% bandwidth), above 5 250 MHz. The 26 dB bandwidth may fall into the 5 250 MHz to 5 350 MHz band; if the occupied bandwidth also falls within the 5 250 MHz to 5 350 MHz band, the transmission is considered as intentional and the devices shall comply with all requirements in the band 5 250 MHz to 5 350 MHz including implementing dynamic frequency selection (DFS) and TPC, on the portion of the emission that resides in the 5 250 MHz to 5 350 MHz band. Complied Module M/N ENWF9203A1EF, ENWF9208A1EF

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 90 RSS-247 Section 6.2.2 Frequency Band (MHz) 5 250 to 5 350 Device Type For devices, other than devices installed in vehicles. Devices out of Scope OEM devices installed in vehicles, Outdoor fixed devices, and other devices ENWF9208A1EF (frequency band not supported)  Channel Tables based on Regulatory Domain/Country Power Limits The maximum conducted output power shall not exceed 250 mW or 11+10 log10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1 MHz band. Unwanted Emission Limits All emissions outside the band 5 250 MHz to 5 350 MHz shall not exceed -27 dBm/MHz e.i.r.p.; or: All emissions outside the band 5 150 MHz to 5 350 MHz shall not exceed -27 dBm/MHz e.i.r.p. and its power shall comply with the spectral power density for operation within the band 5 150 MHz to 5 250 MHz. The device shall be labelled or include in the user manual the following text “For indoor use only.”. RSS-247 Section 6.2.3 Frequency Band (MHz) 5 470 to 5 600 and 5 650 to 5 725 Device Type Devices shall not be capable of transmitting in the band 5 600 MHz to 5 650 MHz. This restriction is for the protection of Environment Canada’s weather radars operating in this band. Devices out of Scope ENWF9208A1EF (frequency band not supported)  Channel Tables based on Regulatory Domain/Country Power Limits The maximum conducted output power shall not exceed 250 mW or 11+10 log10B, dBm, whichever is less. The power spectral density shall not exceed 11 dBm in any 1 MHz band. Unwanted Emission Limits Emissions outside the band 5 470 MHz to 5 725 MHz shall not exceed -27 dBm/MHz e.i.r.p. Devices with bandwidth overlapping the band edge of 5 725 MHz can meet the emission limit of -27 dBm/MHz e.i.r.p. at 5 850 MHz instead of 5 725 MHz. Complied Module M/N ENWF9203A1EF

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 91 RSS-247 Section 6.2.4 Frequency Band (MHz) 5 725 to 5 850 Device Type For equipment operating in the band 5 725 MHz to 5 850 MHz Devices out of Scope Fixed point-to-point devices and devices with antenna gain greater than 6 dBi. Power Limits The minimum 6 dB bandwidth shall be at least 500 kHz. The maximum conducted output power shall not exceed 1 W. The output power spectral density shall not exceed 30 dBm in any 500 kHz band. Unwanted Emission Limits Devices shall have e.i.r.p. of unwanted emissions comply with the following: 27 dBm/MHz at frequencies from the band edges decreasing linearly to 15.6 dBm/MHz at 5 MHz above or below the band edges 15.6 dBm/MHz at 5 MHz above or below the band edges decreasing linearly to 10 dBm/MHz at 25 MHz above or below the band edges 10 dBm/MHz at 25 MHz above or below the band edges decreasing linearly to -27 dBm/MHz at 75 MHz above or below the band edges -27 dBm/MHz at frequencies more than 75 MHz above or below the band edges Complied Module M/N ENWF9203A1EF, ENWF9208A1EF For further information about module variants and its supported channel table please refer to  Channel Tables based on Regulatory Domain/Country.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 92

6.2.2 IC Notice

The device PAN9026 and versions ( 7.1 Ordering Information), including the antennas ( 6.1.5 Approved Antenna List), comply with Canada RSS-Gen Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any inference received, including interference that may cause undesired operation. French Le présent appareil PAN9026 ( 7.1 Ordering Information), les antennes y compris ( 6.1.5 Approved Antenna List), est conforme aux CNR-Gen d'ISDE applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage, et 2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 93

6.2.3 Labeling Requirements

The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifiers are: IC: 216Q-9026 (for M/N: ENWF9203A1EF) IC: 216Q-9026 (for M/N: ENWF9208A1EF) These IC identifiers are valid for all PAN9026 modules  7.1 Ordering Information. In any case, the end product must be labelled on the exterior with: “Contains IC: 216Q-9026”. French Obligations d’étiquetage Les fabricants d’équipements d’origine (FEO) – en anglais Original Equipment Manufacturer (OEM) – doivent s’assurer que les obligations d’étiquetage IC du produit final sont remplies. Ces obligations incluent une étiquette clairement visible à l’extérieur de l’emballage externe, comportant l’identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. L’ identifiant IC est: IC: 216Q-9026 (pour M/N: ENWF9203A1EF) IC: 216Q-9026 (pour M/N: ENWF9208A1EF) Cet identifiant est valide pour tous les modules PAN9026  7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: “Contient IC: 216Q-9026”.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 94

6.3 European Conformity According to RED (2014/53/EU)

The PAN9026 modules with model number ENWF9202A1EF and ENWF9208A1EF comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 62368-1:2014 EN 62311:2008 3.1b EMC: EN 301 489-1 V2.1.1:2017-02 EN 301 489-17 V3.1.1:2017-02 3.2 Radio: EN 300 328 V2.1.1:2016-11 EN 301 893 V2.1.1:2017-04 EN 300 440 V2.1.1:2017-03 As a result of the conformity assessment procedure described in 2014/53/EU Directive, the end customer equipment should be labelled as follows: The end customer has to assure that the device has a distance of more than 20 cm from the human body under all circumstances. The end customer equipment must meet the actual Safety/Health requirements according to RED. PAN9026 and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, and Norway]), Monaco, San Marino, Andorra, and Turkey.

6.3.1 Radio Equipment Directive

The Radio Equipment Directive 2014/53/EU (RED) establishes a regulatory fram ework for placing radio equipment on the market. It ensures a Single Market for radio equipment by setting essential requirements for safety and health, electromagnetic compatibility, and the efficient use of the radio spectrum. The RED aligned the previous Directive, the Radio and Telecommunication Terminal Equipment Directive 1999/5/EC (R&TTED), with the new legislative framework for the marketing of products. The RED is applicable as of 2016-06-13. It included a one-year transitional period, which ended on 2017-06-12 (Article 48). On 2017-06-20, the Commission Implementing

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 95 Regulation (EU) 2017/1354 was adopted. This specifies how to present the information provided for in Article 10(10) of Directive 2014/53/EU. Article 10(10) RED In cases of restrictions on putting into service or of requirements for authorisation of use, information available on the packaging shall allow the identification of the Member States or the geographical area within a Member State where restrictions on putting into service or requirements for authorisation of use exist. Such information shall be completed in the instructions accompanying the radio equipment. The Commission may adopt implementing acts specifying how to present that information. Those implementing acts shall be ado pted in accordance with the advisory procedure referred to in Article 45(2).

• Class 1: Radio equipment that can be operated without any restriction in EU, EEA, and EFTA. According to Article 8(1)b of the RED, it is clarified that no national radio interface s specifications are required to be notified under RED;
• Class 2: Radio equipment subject to restrictions in one or more EU, EEA and EFTA countries where: – The technical parameters are not harmonised through EU, EEA, and EFTA; – The technical parameters are harmonised through EU, EEA and EFTA, and do not fall in above class 1 definition. Radio equipment class means a class identifying particular categories of radio equipment which, under this Directive, are considered similar and those radio interfaces for whi ch the radio equipment is designed. Article 8 RED Notification of radio interface specifications and assignment of radio equipment classes 1 : 1) Member States shall notify, in accordance with the procedure set out in Directive 98/34/EC, the radio interfaces which they intend to regulate except: a) The radio interfaces which fully and without any deviation comply with the Commission decisions on the harmonised use of radio spectrum adopted pursuant to Decision No. 676/2002/EC; and b) The radio interfaces which, in accordance with implementing acts adopted pursuant to paragraph 2 of this Article, correspond to radio equipment which can be put into service and used without restrictions within the Union. 2) The Commission shall adopt implementing acts establishing the equivalence between notified radio interfaces and assigning a radio equipment class, details of which shall be published in the Official Journal of the European Union. Those implementing acts shall be adopted in accordance with the examination procedure referred to in Article 45(3). The Radio Interface Specifications Templates are provided for information in the EFIS database for applications which use is in harmonised radio spectrum, however with restrictions .

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 96

6.3.2 Equipment Classes

The PAN9026 is a radio module classified as class-1 or class-2 radio equipment depending on the frequency band in which it can operate. This equipment class is passed on the end-product which integrates the module. Class 1 Class 1 radio equipment can be placed on the market and put into service without restrictions according to Article 1(3) of Commission Decision 2000/299/EC (Version 2018-01). This radio module is defined as Class 1 radio equipment when it is restricted to operate in the following frequency bands: Sub-class of Class 1 Application/Reference Frequency Band (MHz) Transmit Power/Power Density

22 Wideband Data

2 400 to 2 483.5 100 mW e.i.r.p and 100 mW/100 kHz e.i.r.p. density applies when frequency hopping modulation is used, 10 mW/MHz e.i.r.p. density applies when other types of modulation are used.

54 Wireless Access Systems

including Radio Local Area Networks (WAS/RLANs) EN 301 893 5 470 to 5 725 1 W mean e.i.r.p., 50 mW/MHz mean

43 Non-Specific Short Range

5 725 to 5 875 25 mW e.i.r.p. Class 2 Class 2 radio equipment are restricted in accordance with Article 1(3) of Commission Decision 2000/299/EC1 if the equipment falls within the scope of Class 2. This radio module is also defined as Class 2 radio equipment when it is restricted to operate in the following frequency bands: Sub-class of Class 2 Application/Reference Frequency Band (MHz) Transmit Power/Power Density H01 Wireless Access Systems including Radio Local Area Networks (WAS/RLANs) Restricted to indoor use EN 301 893 10 mW/MHz mean e.i.r.p. density in any 1 MHz band. The usage of PAN9026 module in a vehicular environment cannot be considered as indoor use.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 97

6.4 Bluetooth Qualification

The PAN9026 series modules are Bluetooth qualified as "Controller Subsystem". Following the qualified design ID’s listed for the module: If the module is combined with a host stack that is Bluetooth qualified as "Host Subsystem" it is possible to list an “End Product” without any further qualification tests. The OpenSynergy Bluetooth software is commercially available and is delivered in source code format. Applications that are built using the Blue SDK are executed in Linux user space making development easy. The stack software and profiles are qualified components and are listed on the Bluetooth SIG website.

• Blue SDK v6.x and Low Energy SDK v3.x: QDID 120439
• Bluetooth traditional profiles: QDID 117748 Bluetooth Marks According to the Bluetooth SIG, the PAN9026 fulfills the criteria to label your product as a Bluetooth device: For further information please refer to the Bluetooth website www.bluetooth.com.

6.5 RoHS And REACH Declaration

The latest declaration of environmental compatibility (RoHS and REACH) for supplied products can be found on the Panasonic website in the “Downloads” section of the respective product  7.2.2 Product Information. Bluetooth Product Project Name Power Class Model Declaration ID QDID BR/EDR LE Controller Subsystem PAN9026 Class I 1 1.5 ENWF920xA1EF D044188 128779 PAN9026 Class II 2 2 D044187 129672

 PAN9026 Wi-Fi/Bluetooth Module

7 Appendix

Product Specification Rev. 1.2 Page 98

7.1 Ordering Information

Order Number Brand (Version) Description MOQ22 ENWF9201A1EF PAN9026 (US) Wi-Fi/Bluetooth radio module IEEE 802.11 a/b/g/n Bluetooth /LE 5.0 with a ceramic chip-antenna, US version23 1 000 ENWF9202A1EF PAN9026 (EU) Wi-Fi/Bluetooth radio module IEEE 802.11 a/b/g/n Bluetooth /LE 5.0 with a ceramic chip-antenna, EU version24 1 000 ENWF9203A1EF PAN9026 (CA) Wi-Fi/Bluetooth radio module IEEE 802.11 a/b/g/n Bluetooth /LE 5.0 with a ceramic chip-antenna, CA version25 1 000 ENWF9208A1EF PAN9026 (MR) Wi-Fi/Bluetooth radio module IEEE 802.11 a/b/g/n Bluetooth /LE 5.0 with a ceramic chip-antenna, Multi-region version certified for US, EU, and CA26 1 000 ENWF9209A1EF PAN9026 (WW) Wi-Fi/Bluetooth radio module IEEE 802.11 a/b/g/n Bluetooth /LE 5.0 with a ceramic chip-antenna, non- certifified world-wide version27 1 000 ENWF9201AZEF PAN9026-ETU PAN9026 SDIO Adapter with module ENWF9201A1EF 1 ENWF9201AYEF PAN9026-KIT PAN9026 Kit: 2x PAN9026 SDIO Adapter with module ENWF9201A1EF and 1x Case ENWF9201AXEF PAN9026-IMX i.MX6+PAN9026 Development Kit: 1x PAN9026 MicroSD Adapter, 1x Wandboard WBIMX6U, 1x MicroSD Card, 1x Adapter cable USB-A to DC 5.5/2.5 mm plug ENWF9201AWEF PAN9026-MSD PAN9026 MicroSD Adapter with module ENWF9201A1EF 1 For further information please refer to our product documentation  7.2.2 Product Information. 22 Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 1 000 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels . 23 The US version is restricted to FCC regulatory domain with blocked country code and Tx power table. The device does not support the channels 12 to 13 in the 2.4 GHz band and any non-US channels. TPC, DFS, and passive scanning mechanism are set by the regulatory domain’s channel table, which is stored on the OTP memory of device. 24 The EU version is restricted to European regulatory domain ETSI with blocked country code and Tx power table. TPC, DFS, and passive scanning mechanism are set by the regulator y domain’s channel table, which is stored on the OTP memory of device. 25 The CA version is restricted to Canadian regulatory domain ISED with blocked country code and Tx power table. The device does not support the channels 12 to13 in the 2.4 GHz band and any non-CA channels. TPC, DFS, and passive scanning mechanism are set by the regulatory domain’s channel table, which is stored on the OTP memory of device. 26 The multi-region version is restricted to FCC, European ETSI, and Canadian ISED regulatory domain with blocked Tx power table, which is stored on the OTP memory of device. The device does not support the channels 12 to13 in the 2.4 GHz band. DFS and passive scanning mechanism are not necessary as only the non -DFS channels in the 5 GHz band are supported. 27 The world-wide version is a non-certified variant. Regulatory domain based settings like country code, Tx power, non -usable channels, TPC, DFS, and passive scanning are controlled by the CRDA application on host system. It is necessary to implement a Geo-location mechanism on host platform.

 PAN9026 Wi-Fi/Bluetooth Module Product Specification Rev. 1.2 Page 99

7.2 Contact Details

7.2.1 Contact Us

Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic Sales & Support Tool to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com

7.2.2 Product Information

Please refer to the Panasonic Wireless Connectivity website for further information on our products and related documents: For complete Panasonic product details in the EU, visit http://pideu.panasonic.de/products/wireless-modules.html For complete Panasonic product details in North America, visit http://www.panasonic.com/rfmodules