PAN1720 PANASONIC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 39
Technical content
Bluetooth® Low Energy Module Product Specification Rev. 2.4 Wireless Modules
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 2 Overview The PAN1720/1721 is a Low Energy (LE) module with Texas Instruments CC2540/CC2541 Single Chip Bluetooth LE solution inside. Characteristics
- Bluetooth 4.0
- Output power 4 dBm to -24 dBm
- High sensitivity (-94 dBm typ.)
- Link budget 96 dB
- Operating temperature range -40 °C to +85 °C PAN1720 VS PAN1721 The PAN171x are the non antenna version where the PAN172x are the versions with antenna.
Features
- Surface mount type 15.6 mm x 8.7 mm x 1.8 mm
- PAN1720: Up to 4.0 dBm Tx power (typical) with transmit power control
- PAN1721: CC2541 has typically 0 dBm Tx power
- Texas Instrument’s CC2540/CC2541 Single Chip Bluetooth LE solution inside
- High performance low power 8051 Microcontroller core
- No external components needed
- Fast Connection Setup
- Internal crystal oscillator (32 MHz)
- Internal 32 kHz crystal oscillator for Sleep Timer
- Two powerful USARTs
- UART, USB or I2C interface
- Powerful five channel DMA
- Latest Profiles included e.g. battery monitor and temperature sensor
- Integrated shielding to resist EMI
- Manufactured in conformance with RoHS Block Diagram TI CC254x Crystal 32.768 kHz UART/SPI GPIOs ADC/PWM/Timer Reset USB or I2C Vcc 3.3 V LPF PAN171x Bluetooth 4.0 Module Bluetooth LE RF-PAD Crystal
32 MHz
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 3 TI CC254x Crystal 32.768 kHz UART/SPI GPIOs ADC/PWM/Timer Reset USB or I2C Vcc 3.3 V LPF PAN172x Bluetooth 4.0 Module Bluetooth LE Crystal
32 MHz Chip
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 4 By purchase of any of the products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic Industrial Devices Europe GmbH (Panasonic) reserves the right to make changes as required at any time without notification. Please consult the most recently issued Product Specification before initiating or completing a design. © Panasonic Industrial Devices Europe GmbH 2019. This specification sheet is copyrighted. Reproduction of this document is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Do not disclose it to a third party. All rights reserved. This Product Specification does not lodge the claim to be complete and free of mistakes. Engineering Samples (ES) If Engineering Samples are delivered to the customer, these samples have the status “Engineering Samples”. This means that the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and they may differ from the published Product Specification. Engineering Samples are not qualified and they are not to be used for reliability testing or series production. Disclaimer The customer acknowledges that samples may deviate from the Product Specification and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by: The use of the Engineering Sample other than for evaluation purposes, particularly the installation or integration in another product to be sold by the customer, Deviation or lapse in function of the Engineering Sample, Improper use of the Engineering Sample. Panasonic Industrial Devices Europe GmbH disclaims any liability for consequential and incidental damages. In case of any queries regarding the Engineering Samples, please contact your local sales partner or the related product manager.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 5 Table of Contents
PAN1720/1721 Bluetooth Module
1 About This Document
Product Specification Rev. 2.4 Page 6
1.1 Purpose and Audience
This Product Specification provides details on the functional, operational, and electrical characteristics of the Panasonic PAN1720 and PAN1721 module. It is intended for hardware design, application, and Original Equipment Manufacturers (OEM) engineers. The product is referred to as “the PAN172x” or “the module” within this document.
1.2 Revision History
Revision Date Modifications/Remarks 1.0 2012-04-01 Released version 1.1 2012-07-01 Added chapter “Information regarding Software Versions”. Link to LGA app note. UART pinning for BR-SW version. I2C pinning for PAN1721 version. FCC, IC, IDs. Corrected FCC ID to T7VPAN17. 1.2 2012-08-01 Change IC text in chapter “IC Notice”. New format for chapter “Related Documents”. 1.3 2012-11-01 Added remarks to PAN1721 version. Added non antenna version part number to “Ordering Information”. 1.4 2012-12-01 Added PAN1711 ES information 1.5 2013-01-01 Added dimensions and pinout for the non-antenna versions PAN171x. Minor changes in chapter “RF Exposure”. Added chapter “European R&TTE Declaration of Conformity” Bluetooth Certificiation. 1.6 2013-05-01 Changed Block Diagram 1.7 2013-08-01 Included cross-reference for GPIOs to BlueRadios Pinout 1.8 2013-12-01 Removed QDID from front page. QDID is described in chapter “Bluetooth Certification”. 1.9 2014-11-01 Added radiation pattern for Antenna. Added DoC. 2.0 2015-04-01 Updated REACH RoHS 2.1 2015-07-01 Correction of PAN1721 description 2.2 2017-06-01 Correction of general description 2.3 2018-08-10 Update layout and structure changes 2.4 2019-05-06 Added Yageo antenna to the approved antenna list. Small formatting update. Updated chapter “European Conformity According to RED (2014/53/EU)”.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 7
1.3 Use of Symbols
Indicates important information for the proper use of the product. Non-observance can lead to errors. Attention Indicates important notes that, if not observed, can put the product’s functionality at risk. [chapter number] [chapter title] Cross reference Indicates cross references within the document. Example: Description of the symbols used in this document 1.3 Use of Symbols.
1.4 Related Documents
Please refer to the Panasonic website for related documents 7.2.2 Product Information.
PAN1720/1721 Bluetooth Module
2 Overview
Product Specification Rev. 2.4 Page 8 The PAN172x is a short-range, Class 2, Bluetooth LE single mode module for implementing Bluetooth functionality into various electronic devices. The PAN172x is a cost-effective, low-power, true system-on-chip (SoC) for Bluetooth LE applications. It enables robust Bluetooth LE master or slave nodes to be built with very low total bill-of-material costs. The PAN172x combines an excellent RF transceiver with an industry-standard enhanced 8051 MCU, in-system programmable flash memory, 8-KB RAM, and many other powerful supporting features and peripherals. The PAN172x is suitable for systems where very low power consumption is required. Very low power sleep modes are available. Short transition times between operating modes further enable low power consumption. Panasonic offers Bluetooth low energy protocol stacks and applications from Texas Instruments and BlueRadios. The Bluetooth low energy protocol stack from Texas Instruments, is a flexible and cost-effective single-mode Bluetooth low energy solution. The BlueRadios stack enables rapid and low cost development using an AT command set without the need for a complier. Additional advantages include UART programming, over-the-air-updates, easy integration “C” library framework, serial streaming of data, and smartphone libraries and applications. Please refer to the Panasonic website for related documents 7.2.2 Product Information. Further information on the variants and versions 7.1 Ordering Information.
2.1 Difference between PAN1720/1721
The PAN1721 is pin-compatible with the PAN1720, with the exception that USB is the hardware communication interface on the PAN1720 and I2C is the hardware communication interface on the PAN1721. Compared to the PAN1720, the PAN1721 provides lower RF current consumption. The PAN1721 does not have the USB interface found on the PAN1720, and provides lower maximum output power in TX mode. Both ICs the CC2540 as well as the CC2541 come with an internal 256 KB flash memory. Brand Name Description PAN1720 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0 Bluetooth smart device PAN1720 Same as above including BlueRadios BR-SPP FW version. PAN1721 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0 PAN1721 Same as above including BlueRadios BR-SPP FW version.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 9 Brand Name Description PAN1711 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0 Bluetooth smart device without antenna PAN1711 Same as above without antenna including BlueRadios BR-SPP FW version.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 10
2.2 Block Diagram
32.768 kHz UART/SPI GPIOs ADC/PWM/Timer Reset USB or I2C Vcc 3.3 V LPF PAN171x Bluetooth 4.0 Module Bluetooth LE RF-PAD Crystal 32.768 kHz UART/SPI GPIOs ADC/PWM/Timer Reset USB or I2C Vcc 3.3 V LPF PAN172x Bluetooth 4.0 Module Bluetooth LE Crystal
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 11
2.3 Pin Configuration
No Pin Name Pin Type Description A1 GND Ground Pin Connect to ground A2 P1.0 Digital I/O Port 1.0 – 20 mA drive capability A3 RESET Digital Input Reset, active low A4 VCC Power Analog/digital power supply connection A5 VCC Power Analog/digital power supply connection A6 VCC Power Analog/digital power supply connection A7 GND Ground Pin Connect to ground A8 NC Not connected A9 GND Ground Pin Connect to ground A11 GND Ground Pin Connect to ground A12 GND Ground Pin Connect to ground B1 P1.3 Digital I/O Port 1.3 B2 P1.2 Digital I/O Port 1.2 F2 F3 F4 F5 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 C1 C2 C3 C4 C5 C6 C7 C8 B1 B2 B3 B4 B5 B6 B7 B8 B9 A2 A3 A4 A5 A6 A7 A8A1 1.0 8.70 mm 0.6 5.0 0.6 1.35 1.351.2 1.2 F7F1 F8 15.6 mm F6 F11 A11 F12 A12 2.4
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 12 No Pin Name Pin Type Description B3 P1.1 Digital I/O Port 1.1 – 20 mA drive capability B4 P0.6 Digital I/O Port 0.6 B5 NC Not connected B6 P0.1 Digital I/O Port 0.1 B7 P0.0 Digital I/O Port 0.0 B8 NC Not connected B9 NC Not connected, C1 NC Not connected, C2 P1.4 Digital I/O Port 1.4/BR-SW UART CTS C3 P1.5 Digital I/O Port 1.5/BR-SW UART RTS C4 P0.7 Digital I/O Port 0.7 C5 NC Not connected C6 NC Not connected C7 NC Not connected C8 GND Ground Pin Connect to ground C9 GND Ground Pin Connect to Ground D1 DVDD_USB Power (digital) 2 V-3.6 V digital power supply connection D2 USB_N Digital I/O USB N/PAN17x1 I2C SDA Leave floating if not used. D3 USB_P Digital I/O USB P/PAN17x1 I2C SCL Leave floating if not used D4 NC Not connected D5 NC Not connected D6 NC Not connected D7 GND Ground Pin Connect to ground D8 GND Ground Pin Connect to ground D9 NC/RF PAN172x not Connected/50 Ω RF_Out PAN171x E1 P2.1/DD Digital I/O Port 2.1/Programming Interface DD E2 P2.2/DC Digital I/O Port 2.2/Programming Interface DC E3 DGND_USB Ground Pin Connect to Ground E4 NC Not connected E5 NC Not connected E6 P0.2/RX/MISO Digital I/O Port 0.2/TI-SW UART RX/SPI MISO
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 13 No Pin Name Pin Type Description E7 NC Not connected E8 GND Ground Pin Connect to ground E9 GND Ground Pin Connect to ground F1 GND Ground Pin Connect to ground F2 P1.6 Digital I/O Port 1.6/BR-SW UART TX F3 P1.7 Digital I/O Port 1.7/BR-SW UART RX F4 P2.0 Digital I/O Port 2.0 F5 P0.4/CTS/CS Digital I/O Port 0.4/TI-SW UART CTS/SPI CS F6 NC Not connected F7 P0.3/TX/MOSI Digital I/O Port 0.3/TI-SW UART TX/SPI MOSI F8 P0.5/RTS/CLK Digital I/O Port 0.5/TI-SW UART RTS/SPI CLK F9 GND Ground Pin Connect to ground F11 GND Ground Pin Connect to ground F12 GND Ground Pin Connect to ground
2.4 UART Interface
- Full-duplex 4-wire data transfer: RX, TX, RTS, and CTS
- Default baud rate: 115 200 bps
- Data format: 8N1
2.5 Bluetooth Features
- Bluetooth 4.0 single mode low energy technology.
- Class 2 TX power w/o external PA, improving link robustness.
- Excellent link budget (up to 96 dB), enabling long-range applications.
- Accurate digital received signal-strength indicator (RSSI)
- Integrates the new low power profiles and services
- Embedded Bluetooth-Stack available
PAN1720/1721 Bluetooth Module
3 Detailed Description
Product Specification Rev. 2.4 Page 14
3.1 Dimensions
All dimensions are in millimeters. PAN172x No. Item Dimension Tolerance Remark 1 Width 8.70 ±0.20 2 Length 15.60 ±0.20 3 Height 1.80 ±0.20 With case
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 15 PAN171X No. Item Dimension Tolerance Remark 1 Width 8.70 ±0.20 2 Length 11.60 ±0.20 3 Height 1.80 ±0.20 With case
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 16
3.2 Footprint
The outer dimensions have a tolerance of 0.2 mm. PAN172x Top View PAN171X Top View F2 F3 F4 F5 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 C1 C2 C3 C4 C5 C6 C7 C8 B1 B2 B3 B4 B5 B6 B7 B8 B9 A2 A3 A4 A5 A6 A7 A8A1 1.0 8.70 mm 0.6 5.0 0.6 1.35 1.351.2 1.2 F7F1 F8 15.6 mm F6 F11 A11 F12 A12 2.4 F2 F3 F4 F5 E1 E2 E3 E4 E5 E6 E7 E8 E9 D1 D2 D3 D4 D5 D6 D7 D8 C1 C2 C3 C4 C5 C6 C7 C8 B1 B2 B3 B4 B5 B6 B7 B8 B9 A2 A3 A4 A5 A6 A7 A8A1 1.0 8.70 mm 0.6 0.6 1.35 1.351.2 1.2 F7F1 F8 11.6 mm
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 17
3.3 Packaging
The product is a mass production status product and will be delivered in the package described below.
3.3.1 Tape Dimensions
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 18
3.3.2 Packing in Tape
Empty spaces in the component packed area shall be less than two per reel and those spaces shall not be consecutive. The top cover tape shall not be found on reel holes and it shall not stick out from the reel.
3.3.3 Component Direction
100730-PAN1720.vsd trailer (empty) 1 x circumference / hub (min 160mm) component packed area standard 1500pcs leader (empty) minimum 10 pitch Top cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules. Direction of unreeling (for customer)
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 19
3.3.4 Reel Dimension
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 20
3.3.5 Package Label
(1T) (1P) (2P) (9D) (Q) (HW/SW) Lot code Customer order number, if applicable Order number Date code Quantity Hardware/software version
3.3.6 Total Package
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 21
3.4 Case Marking
Engineering Sample marking, if applicable Marking for Pin 1 2D barcode, for internal usage only
PAN1720/1721 Bluetooth Module
4 Specification
Product Specification Rev. 2.4 Page 22 All specifications are over temperature and process, unless indicated otherwise.
4.1 Default Test Conditions
Temperature: 25±10 °C Humidity: 40-85 % RH Supply Voltage: 3.3 V
4.2 Absolute Maximum Ratings
The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TSTOR Storage Temperature -40 +125 °C VESD ESD Robustness All pads, according to human body model (HBM), JEDEC STD 22, method A114 1 000 V According to charged device model (CDM), JEDEC STD 22, method C101 500 V PRF RF Input Level +10 dBm VDIG Voltage on any Digital Pins -0.3 VDD +0.3 V
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 23
4.3 Recommended Operating Conditions
The maximum ratings may not be exceeded under any circumstances, not even momentarily or individually, as permanent damage to the module may result. Symbol Parameter Condition Min. Typ. Max. Units TA Ambient Operating Temperature Range -40 +85 °C VDD 3V3 Supply Voltage 2 3.3 3.6 V
4.4 Current Consumption
The current consumption depends on the user scenario and on the setup and timing in the power modes. Assume VDD=3 V, Tamb=25 °C, if nothing else stated. Parameter Condition Min. Typ. Max. Units Icore Core Current Consumption Power mode 1. Digital regulator on; 16 MHz RCOSC and 32 MHz crystal oscillator off; 32.768 kHz XOSC, POR, BOD and sleep timer active; RAM and register retention. 235 μA Power mode 2. Digital regulator off; 16 MHz RCOSC and 32 MHz crystal oscillator off; 32.768 kHz XOSC, POR, and sleep timer active; RAM and register retention. 0.9 Power mode 3. Digital regulator off; no clocks; POR active; RAM and register retention 0.4 Low MCU activity: 32 MHz XOSC running. No radio or peripherals. No flash access, no RAM access. 6.7 mA Iperi Peripheral Current Consumption (Add to core current Icore for Timer 1. Timer running, 32 MHz XOSC used 90 μA Timer 2. Timer running, 32 MHz XOSC used 90 μA Timer 3. Timer running, 32 MHz XOSC used 60 μA Timer 4. Timer running, 32 MHz XOSC used 70 μA Sleep timer, including 32.753 kHz RCOSC 0.6 μA
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 24 Parameter Condition Min. Typ. Max. Units each peripheral unit activated) ADC, when converting 1.2 mA Power mode 1 (Active) Digital regulator on, 16 MHz RCOSC and 32 MHz crystal oscillator off. Startup of
16 MHz RCOSC
4 μs Power mode 2 or power mode 3 (Active) Digital regulator off, 16 MHz RCOSC and 32 MHz crystal oscillator off. Startup of regulator and 16 MHz RCOSC 120 μs TX or RX Crystal ESR=16 Ω. Initially running on
16 MHz RCOSC, with 32 MHz XOSC off
410 μs With 32 MHz XOSC initially on 160 μs RX/TX turnaround 150 μs RF frequency range Programmable in 2 MHz steps 2 402 2 480 MHz Data rate and modulation format
1 Mbps, GFSK, 250 kHz deviation
4.5 Bluetooth
Parameter Condition Min. Typ. Max. Units Operation Frequency Range 2 402 2 480 MHz Channel Spacing Bluetooth LE 2 MHz Output Power Maximum setting, measured at single ended 50 Ω. 4 dBm Maximum setting, measured at single ended 50 Ω. -24 dBm Sensitivity High-gain Mode -93 dBm Standard Mode -92.5
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 25 PAN1721 Parameter Condition Min. Typ. Max. Units Operation Frequency Range 2 402 2 480 MHz Channel Spacing Bluetooth LE 2 MHz Output Power Maximum setting, measured at single ended 50 Ω. 0 dBm Maximum setting, measured at single ended 50 Ω. -24 dBm Sensitivity High-gain Mode -93 dBm Standard Mode -92.5 PAN1720/1721 Symbol Parameter Condition Min. Typ. Max. Units
1 Spurious
Conducted measurement with a 50 Ω single-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66. <-30 -41 dBm
4.6 Reliability Tests
The measurement should be done after the test device has been exposed to room temperature and humidity for one hour. No. Item Limit Condition
1 Vibration test Electrical parameter should be
- Freq.: 10~50 Hz; Amplitude: 1.5 mm; 20 min./cycle, 1 h each of XYZ axis
- Freq.: 30~100 Hz, 6 G; 20 min./cycle, 1 h each of XYZ axis
2 Shock test See above Dropped onto hard wood from a height
3 Heat cycle test See above -40 °C for 30 min. and +85 °C for 30 min.; each temperature 300 cycles
4 Moisture test See above +60 °C, 90 % RH, 300 h
5 Low temperature test See above -40 °C, 300 h
6 High temperature test See above +85 °C, 300 h
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 26
4.7 Recommended Soldering Profile
Reflow permissible cycles: 2 Opposite side reflow is prohibited due to module weight More than 75 percent of the soldering area shall be coated by solder The soldering profiles should be adhered to in order to prevent electrical or mechanical damage Soldering profile assumes lead-free soldering
PAN1720/1721 Bluetooth Module
5 Cautions
Product Specification Rev. 2.4 Page 27 Failure to follow the guidelines set forth in this document may result in degrading of the modules functions and damage to the module.
5.1 Design Notes
- Follow the conditions written in this specification, especially the control signals of this module. 2. The supply voltage must be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47 µF directly at the module). 3. This module should not be mechanically stressed when installed. 4. Keep this module away from heat. Heat is the major cause of decreasing the life time of these modules. 5. The supply voltage should abide by the maximum ratings ( 4.2 Absolute Maximum Ratings). It should not carry noise and/or spikes. 6. Avoid assembly and use of the target equipment in conditions where the module temperature may exceed the maximum tolerance. 7. Keep this module away from other high frequency circuits. 8. Refer to the recommended pattern when designing a board.
5.2 Installation Notes
- Reflow soldering is possible twice based on the conditions set forth in 4.7 Recommended Soldering Profile. Set up the temperature at the soldering portion of this module according to this reflow profile. 2. Carefully position the modules so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. 3. Carefully locate the module, to avoid an increased temperature caused by heat generated by neighboring components. 4. If a vinyl-covered wire comes into contact with the module, the wire cover will melt and generate toxic gas, damaging the insulation. Never allow contact between a vinyl cover and these modules to occur. 5. This module should not be mechanically stressed or vibrated when reflowed. 6. To repair the board by hand soldering, follow the conditions set forth in this chapter. 7. Do not wash the module. 8. Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 28
5.3 Usage Condition Notes
- Take measures to protect the module against static electricity. If pulses or transient loads (a large load, which is suddenly applied) are applied to the modules, check and evaluate their operation before assembly of the final products. 2. Do not use dropped modules. 3. Do not touch, damage or soil the pins. 4. Follow the recommended condition ratings about the power supply applied to this module. 5. Electrode peeling strength: Do not apply a force of more than 4.9 N in any direction on the soldered module. 6. Pressing on parts of the metal cover or fastening objects to the metal cover will c ause damage. 7. These modules are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information, and communication equipment.
5.4 Storage Notes
- The module should not be stressed mechanically during storage. 2. Do not store these modules in the following conditions or the performance characteristics of the module, such as RF performance will be adversely affected: – Storage in salty air or in an environment with a high concentration of corrosive ga s, such as Cl2, H2S, NH3, SO2, or NOX, – Storage in direct sunlight, – Storage in an environment where the temperature may be outside the range of 5 °C to 35 °C, or where the humidity may be outside the 45 % to 85 % range, – Storage of the modules for more than one year after the date of delivery storage period: Please check the adhesive strength of the embossed tape and soldering after six months of storage. 3. Keep this module away from water, poisonous gas, and corrosive gas. 4. This module should not be stressed or shocked when transported. 5. Follow the specification when stacking packed crates (max. 10).
5.5 Safety Cautions
These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, provide the following failsafe functions as a minimum:
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 29 1. Ensure the safety of the whole system by installing a protection circuit and a protection device. 2. Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status.
5.6 Other Cautions
- Do not use the module for other purposes than those listed in section 5.3 Usage Condition Notes. 2. Be sure to provide an appropriate fail-safe function on your product to prevent any additional damage that may be caused by the abnormal function or the failure of the module. 3. This module has been manufactured without any ozone chemical controlled under the Montreal Protocol. 4. These modules are not intended for use under the special conditions shown below. Before using these modules under such special conditions, carefully check their performance and reliability under the said special conditions to determine whether or not they can be used in such a manner: – In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash, – In direct sunlight, outdoors, or in a dusty environment, – In an environment where condensation occurs, – In an environment with a high concentration of harmful gas (for exmaple salty air, HCl, Cl2, SO2, H2S, NH3, and NOX). 5. If an abnormal voltage is applied, due to a problem occurring in other components or circuits, replace these modules with new modules. They may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. Please refer to the Panasonic website for for further information 7.2.2 Product Information.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 30
5.7 Restricted Use
5.7.1 Life Support Policy
This Panasonic Industrial Devices Europe GmbH product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic Industrial Devices Europe GmbH for any damages resulting.
5.7.2 Restricted End Use
This Panasonic Industrial Devices Europe GmbH product is not designed for any restricted activity that supports the development, production, handling usage, maintenance, storage, inventory or proliferation of any weapons or military use. Transfer, export, re-export, usage or reselling of this product to any destination, end user or any end use prohibited by the European Union, United States or any other applicable law is strictly prohibited.
PAN1720/1721 Bluetooth Module
6 Regulatory and Certification Information
Product Specification Rev. 2.4 Page 31
6.1 Federal Communications Commission (FCC) for US
6.1.1 FCC Notice
The PAN172x including the antennas, which are listed in 6.1.5 Approved Antenna List, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407. The transmitter operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
6.1.2 Caution
The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to co rrect the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna,
- Increase the separation between the equipment and receiver,
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected,
- Consult the dealer or an experienced radio/TV technician for help.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 32
6.1.3 Label Requirements
The OEM must ensure that FCC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7VPAN17. This FCC identifier is valid for the PAN172x. The end product must in any case be labelled on the exterior with: "Contains FCC ID: T7VPAN17"
6.1.4 Antenna Warning
This antenna warning refers to the test device with the model number PAN172x 7.1 Ordering Information The device is tested with a standard SMA connector and with the antenna listed below. When integrated into the OEM’s product, these fixed antennas require installation preventing end users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and with Section 15.247 for emissions. The FCC identifier for the device with the antenna listed in 6.1.5 Approved Antenna List is the same (FCC ID: T7VPAN17).
6.1.5 Approved Antenna List
Item Part Number Manufacturer Frequency Band Type Gain (dBi) 1 LDA212G3110K Murata 2.4 GHz Chip antenna +0.9 2 ANT2012LL13R2400A Yageo 2.4 GHz Chip antenna +0.9
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 33
6.1.6 RF Exposure
To comply with FCC RF Exposure requirements, the OEM must ensure that only antennas from the Approved Antenna List are installed 6.1.5 Approved Antenna List. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of the PAN172x with a mounted ceramic antenna (FCC ID: T7VPAN17) is below the FCC radio frequency exposure limits. Nevertheless, the PAN172x shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance.
6.2 Innovation, Science, and Economic Development (ISED) for
The PAN172x is licensed to meet the regulatory requirements of ISED. License ID: IC: T7VPAN17 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in 6.1.5 Approved Antenna List, having a maximum gain of +0.9 dBi. Antennas not included in this list or having a gain greater than +0.9 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 Ohm. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size, the IC identifier is displayed in the installation instruction only and it cannot be displayed on the module’s label due to the limited size. French PAN172x est garanti conforme aux dispositions règlementaires d’Industry Canada (ISED). License: IC: T7VPAN17 Il est recommandé aux fabricants d’appareils fixes, mobiles ou portables de consulter la réglementation en vigueur et de vérifier la conformité de leurs produits relativement aux limites
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 34 d’exposition aux rayonnements radiofréquence ainsi qu’au débit d’absorption spécifique maximum autorisé. Des informations pour les utilisateurs sur la réglementation Canadienne concernant l’exposition aux rayonnements RF sont disponibles sur le site www.ic.gc.ca. Ce produit a été développé pour fonctionner spécifiquement avec les antennes listées dans le tableau 6.1.5 Approved Antenna List, présentant un gain maximum de 0.9 dBi. Des antennes autres que celles listées ici, ou présentant un gain supérieur à 0.9 dBi ne doivent en aucune circonstance être utilisées en combinaison avec ce produit. L’impédance des antennes compatibles est 50 Ohm. L’antenne utilisée avec ce produit ne doit ni être située à proximité d’une autre antenne ou d’un autre émetteur, ni être utilisée conjointement avec une autre antenne ou un autre émetteur. En raison de la taille du produit, l’identifiant IC est fourni dans le manuel d’installation.
6.2.1 IC Notice
The device PAN172x ( 7.1 Ordering Information), including the antennas ( 6.1.5 Approved Antenna List), complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-Gen. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. French Le présent appareil PAN172x ( 7.1 Ordering Information), les antennes y compris ( 6.1.5 Approved Antenna List), est conforme aux CNR-Gen d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: 1. L'appareil ne doit pas produire de brouillage, et 2. L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 35
6.2.2 Labeling Requirements
The OEM must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is: IC: T7VPAN17 This IC identifier is valid for all PAN172x modules 7.1 Ordering Information. In any case, the end product must be labelled on the exterior with: "Contains IC: T7VPAN17”. French Obligations d’étiquetage Les fabricants d’équipements d’origine (FEO) – en anglais Original Equipment Manufacturer (OEM) – doivent s’assurer que les obligations d’étiquetage IC du produit final sont remplies. Ces obligations incluent une étiquette clairement visible à l’extérieur de l’emballage externe, comportant l’identifiant IC du module Panasonic inclus, ainsi que la notification ci-dessus. L’ identifiant IC est: IC: T7VPAN17 Cet identifiant est valide pour tous les modules PAN172x 7.1 Ordering Information. Dans tous les cas les produits finaux doivent indiquer sur leur emballage externe la mention suivante: "Contient IC: T7VPAN17”.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 36
6.3 European Conformity According to RED (2014/53/EU)
All modules described in this product specification comply with the standards according to the following LVD (2014/35/EU), EMC-D (2014/30/EU) together with RED (2014/53/EU) articles: 3.1a Safety/Health: EN 60950-1:2006+A11:2009+A1:2010+A12:2011+AC:2011+A2:2013 EN 62311:2008 EN 62479:2010 3.1b EMC: EN 301 489-1 V2.1.1:2017-02 EN 301 489-17 V3.1.1:2017-02 3.2 Radio: EN 300 328 V2.1.1:2016-11 As a result of the conformity assessment procedure described in 2014/53/EU Directive, the end customer equipment should be labelled as follows: The end customer has to assure that the device has a distance of more than 20 cm from the human body under all circumstances. The end customer equipment must meet the actual Safety/Health requirements according to RED. PAN172x and its model versions in the specified reference design can be used in all countries of the European Economic Area (Member States of the EU, European Free Trade Association States [Iceland, Liechtenstein, Norway]), Monaco, San Marino, Andorra, and Turkey.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 37
6.4 Bluetooth
Bluetooth end products which integrate the PAN172x need to receive the following IDs at creation: Bluetooth 3.0 Declaration ID QDID Profile SubSystem (SDP/SPP) B019234 36438 Controller Subsystem B020093 40254 Host Subsystem B019248 38386 Bluetooth 4.0 Declaration ID QDID Profile Subsystem (Gatt) B019935 40735 Controller Subsystem B021165 48177 Host Subsystem B020932 48566 Bluetooth Marks According to the Bluetooth SIG, the PAN172x fulfills the criteria to label your product as a Bluetooth device: For further information please refer to the Bluetooth website www.bluetooth.com.
6.5 RoHS and REACH Declaration
The latest declaration of environmental compatibility (Restriction of Hazardous Substances, RoHS and Registration, Evaluation, Authorisation and Restriction of Chemicals, REACH) for supplied products can be found on the Panasonic website in the “Downloads” sec tion of the respective product 7.2.2 Product Information.
PAN1720/1721 Bluetooth Module
7 Appendix
Product Specification Rev. 2.4 Page 38
7.1 Ordering Information
Order Number Brand Name Description MOQ1 ENW89820A1KF PAN1720 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0. Bluetooth smart device 1 500 ENW89820A3KF PAN1720 Same as above including BlueRadios BR-SPP FW version. Bluetooth smart device 1 500 ENW89835A1KF PAN1721 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0. Bluetooth smart device 1 500 ENW89835A3KF PAN1721 Same as above including BlueRadios BR-SPP FW version. Bluetooth smart device 1 500 ENW89835C1KF PAN1711 CLASS 2 Bluetooth single mode Module according Bluetooth 4.0. Bluetooth smart device without antenna ES ENW89835C3KF PAN1711 Same as above without antenna including BlueRadios BR-SPP FW version. Bluetooth smart device without antenna ES 1 Abbreviation for Minimum Order Quantity (MOQ). The default MOQ for mass production is 1 500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels.
PAN1720/1721 Bluetooth Module Product Specification Rev. 2.4 Page 39
7.2 Contact Details
7.2.1 Contact Us
Please contact your local Panasonic Sales office for details on additional product options and services: For Panasonic Sales assistance in the EU, visit https://eu.industrial.panasonic.com/about-us/contact-us Email: wireless@eu.panasonic.com For Panasonic Sales assistance in North America, visit the Panasonic website “Sales & Support” to find assistance near you at https://na.industrial.panasonic.com/distributors Please visit the Panasonic Wireless Technical Forum to submit a question at https://forum.na.industrial.panasonic.com
7.2.2 Product Information
Please refer to the Panasonic Wireless Connectivity website for further information on our products and related documents: For complete Panasonic product details in the EU, visit http://pideu.panasonic.de/products/wireless-modules.html For complete Panasonic product details in North America, visit http://www.panasonic.com/rfmodules