P0080SB UNSEMI | Alldatasheet
Document overview
- Manufacturer or author: Provided By alldatasheet.com(free datasheet download site)
- PDF pages: 6
Technical content
Description
Applicable Global Standards ROHS www.unsemi.com.tw Features and Benefits Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.1/5 P0080SB - P5000SB Series Thyristor Surge Suppressors (TSS) DO-214AA(SMB) @10/700μSđ4KV Schematic Symbol Electrical Parameters P0080SB- P5000SB Series are designed to protect broadband equipment such as modems, line card, CPE and DSL from damaging over-voltage transients. The series provides a surface mount solution that enables equipment to comply with global regulatory standards. Low voltage overshoot Low on-state voltage Does not degrade surge capability after multiple surge events within limit Fails short circuit when surged in excess of ratings Low Capacitance TIA-968-A ITU K.20/21 Enhanced level ITU K.20/21 Basic Level GR 1089 Inter building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Parameter IS lDRM IH IT VS VDRM Vτ Definition Off-state Capacitance - typical capacitance measured in off state On-state Voltage - maximum voltage measured at rated on-state current Peak Off-state Voltage - maximum voltage that can be applied while maintaining off state Switching Voltage - maximum voltage prior to switching to on stat On-state Current - maximum rated continuous on-state bcurrent Holding Current - minimum current required to maintain on state Leakage Current - maximum peak off-state current measured at VDRM Switching Current - maximum current required to switch to on state IS lDRM IH IT VS VDRMVτ +V- V
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Thyristor Surge Suppressors (TSS) DO-214AA(SMB) @10/700μSđ4KV Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. P0080SB - P5000SB Series
Electrical Characteristics
2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 150 Part Number P008B P03B P06B P07B P09B P11B P13B P15B P18B P20B P23B P26B P31B P35B P38B P42B P45B P50B Marking pF Typ. V DRM @IDRM=5μA IDRM VS @100V/μS IS VT @IT=2.2A IT CO @1MHzIH Surge Ratings Series 2/10μS¹ 2/10μS² A min 8/20μS¹ 1.2/50μS² A min 10/160μS¹ 10/160μS² A min 250 250 250 10/560μS¹ 10/560μS² A min 200 10/1000μS¹ 10/1000μS² A min 5/320μS¹ ITSM 50/60HZ10/700μS² di/dt A min A min Amps/µs max 100 30 500 B Notes: 1. Current waveform in µs 2. Voltage waveform in µs Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional. - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP ratings applicable over temperature range of -40ºC to +85ºC - The device must initially be in thermal equilibrium with -40°C < TJ < +150°C
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Thyristor Surge Suppressors (TSS) Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.4/5 Soldering Parameters ROHS Environmental Specifications Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 DO-214AA(SMB) @10/700μS, 4KV P0080SB - P5000SB Series High Temp Voltage Blocking 80% Rated VDRM (VAC Peak ) +125°C or +150°C, Lead Material Copper Alloy High Temp Voltage Blocking 504 or 1008 hrs. MIL-STD-750 (Method 1040) JEDEC, JESD22-A-101 -65°C to +150°C, 15 min. dwell, 10 up to 100 cycles.MIL-STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC (+85°C) 85%RH, 504 up to 1008 hrs. EIA/ JEDEC, JESD22-A-101 +150°C 1008 hrs. MIL-STD-750 (Method 1031) JEDEC, JESD22-A-101 85%RH, +85°C, 168 hrs., 3 reflow cycles Level (+260°C Peak). JEDEC-J-STD-020, Level 1 -65°C, 1008 hrs. 0°C to +100°C, 5 min. dwell, 10 sec. transfer, Thermal Shock 10 cycles. MIL-STD-750 (Method 1056) JEDEC, JESD22-A-106 +121°C, 100%RH, 2atm, 24 up to 168 hrs. EIA/Cooker Test) JEDEC, JESD22-A-102 +260°C, 30 secs. MIL-STD-750 (Method 2031 Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Temp Cycing TimeTime to peak temperature ( T25℃ to peak) Preheat Ts(min) Ts(max) TL TL TP Temperature Ramp-up Ramp-down Critical Zone TL toTP TP Ts Lead–free assembly +150°C +200°C 60 -180 Seconds 3°C/Second max 5°C/Second max 217°C 60 -150 Seconds 260 +0/-5°C
30 Seconds Max
6°C/Second Max 8 minutes Max +260°C Reflow Condition Pre Heat -Temperature Min (Ts(min)) -Temperature Max (Ts(max)) - Time (min to max) (TS) Average ramp up rate ( Liquidus Temp TL) to peak TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Time (min to max) (TS) Peak Temperature (TP) Do not exceed Time 25°C to peak Temperature (TP) Time within 5°C of actual peak Temperature (TP) Ramp-down Rate
Thyristor Surge Suppressors (TSS) Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information.5/5 Part Numbering ROHS P0080SB - P5000SB Series Packaging Tape and Reel Specifications Dimensions DO-214AA Part Marking P XXX 0 S B Type Median Voltage Construction Variable, 0: One chip 2: Two chip E: ESD Protection Packge Type, IPP Rating S:DO- 214AA(SMB) T:DO- 214AC(SMA) E:TO- 92 L:DO-15,DO- 27,DQ- 41 Y: SMB- H A: @10/700μs 2KV (50A) B: @10/700μs 4KV (100A) C: @10/700μs 6KV (150A) Part Marking Code (Refer to Electrical Characteristics Table) Date code PXXXB XXXX DO-214AA(SMB) @10/700μS, 4KV Pxxx0SB Part Number Component Package DO-214AA 2500 Tape & Reel -12mm/13″tape EIA -481 - D Quantity Packaging Option Packaging Specification Direction of Feed 0.63 (15.88) 0.512(13.0) Arbor Hole Diameter 13.0 (330.0) 0.157 (4.0) 0.315 (8.0) 0.35 (9.00) 0.061 (1.5) 0.472 (12.0) Cover tape Diameter Dimensions Inches Millimeters Min Min A B C D E F G H K 0.130 0.201 0.077 0.159 0.030 0.076 0.002 0.077 0.006 0.156 0.220 0.087 0.181 0.063 0.096 0.008 0.104 0.016 3.30 5.10 1.95 4.05 0.76 1.90 0.05 1.95 0.15 3.95 5.60 2.20 4.60 1.60 2.45 0.20 2.65 0.41 Max Max H K G 0.079 (2.0) 0.085 (2.16) 0.07 Inch (millimeter) Pad outline (1.78) AC D B E F
Revision March 1,2022 www.unsemi.com.tw For technical questions, contact: tech@unsemi.com.tw ROHS Specifications are subject to change without notice. Please refer to www.unsemi.com.tw for current information. Disclaimer ROHS UNSEMI RESERVES THE RIGHT TO MAKE CHANGE ON OUR PRODUTS , PRODUCTS SPECIFICATION AND DATA WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. UN SEMICONDUCTOR LIMITED its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “UNSEMI”)does not give any representations or warranties for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. In no event shall UNSEMI be liable for any indirect, incidental, punitive, special or consequential damages (including any and all implied warranties, warranties of fitness for particular purpose, non-infringement and merchantability.) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. Statements regarding the suitability of products for certain types of applications are based on UNSEMI knowledge of typical requirements that are often placed on UNSEMI products in generic applications. Such statements are not binding, statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify UNSEMI's terms and conditions of purchase, including but not limited to the warranty expressed therein. Unless otherwise agreed in writing, UNSEMI product is not designed, authorized or warranted to be suitable for use in medical life-saving, or life-sustaining application , nor in applications where failure or malfunction of a UNSEMI product can reasonably be expected to result in personal injury, death or severe property or environmental damage. UNSEMI and its suppliers accept no liability for inclusion or use of UNSEMI products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. All referenced brands, product names, service names and trademarks are the property of their respective owners.