P48WG_14 PEAK | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

PM8-Series – P48WG-xxxxE/Z2:1LF – Single and Dual O utput – 2”x1” - Metal Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 1/4 P48WG-xxxxE/Z2:1LF All specifications typical at Ta=25° C, nominal input voltage and full load unless otherwise specified Input Specifications Voltage Range 2:1 Wide Input Input Filter PI Type Input Reflected Ripple Current¹ 20 mA pk-pk Start up Time (Nom. Vin and constant resistive load) 20mS, typ. Output Specifications Voltage Accuracy ± 1% Voltage Adjustability (Trim – only Single Output) ± 10%, max. Short Circuit Protection Indefinite (Hiccup, Automatic Recovery) Over Current Protection 140% of max. Iout Line Regulation ± 0.2% Load Regulation (0% - 100%) ± 0.5% (Single), ± 1% (Dual) Cross Regulation³ (Dual Output) ± 5% Ripple and Noise (20Mhz bandwidth) 75 mV pk-pk Temperature Coefficient ± 0.02% / ° C Transient Recovery Time 4 250us, typ. Transient Response Deviation 4 ± 3%, max. General Specifications Efficiency See Table I/O Isolation Voltage (3 sec.) 1500 VDC I/O Isolation Capacitance 1200 pF, typ. I/O Isolation Resistance 1000 M Ohm Switching Frequency 330 kHz, typ. Humidity 95% rel H Reliability Calculated MTBF (MIL-HDBK-217F) > 0.684 Mhrs Physical Specifications Case Material Nickel Coated Copper Potting Material Epoxy (UL94V-0 rated) Weight ~ 30g, typ. Environment Specifications Operating Temperature -40 to +71° C (ambient) Maximum Case Temperature 100° C Storage Temperature -40 to +125° C Cooling Free Air Convection RoHS Conform Soldering 260° C, max. (1.5mm from case 10s.) Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de peak@peak-electronics.de The PM8 series is a family of cost effective 20 W, single & dual output DC/DC converters with a wide 2:1 Input. These converters are encapsulated in nickel coated copper 2”x1” case with high performance technology like active clamp, high efficiency opera tion and output voltage accuracy of ±1% maximum. Precise controlled design provides tight line / load regulation PM8-SERIES /checkbld 20 Watt /checkbld 2:1 Wide Input /checkbld Reg. Single and Dual Output /checkbld 2” x 1” Case /checkbld 1.5 kV DC I/O Isolation /checkbld Over Voltage/Current Protection /checkbld Soft Start and Remote Ctrl. Rev.12-2008

PM8-Series – P48WG-xxxxE/Z2:1LF – Single and Dual O utput – 2”x1” - Metal Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 2/4 Selection Guide Single and Dual Output Order # In p u t V o lta g e (V D C ) In p u t C u rre n t N o L o a d (m A ) In p u t C u rre n t F u ll L o a d (m A ) O u tp u t V o lta g e (V D C ) O u tp u t C u rre n t M in . L o a d (m A ) O u tp u t C u rre n t F u ll L o a d (m A ) E ffic ie n c y (% ) C a p a c ito r L o a d (u F )² SINGLE OUTPUT P48WG-123R3E2:1LF 9-18 60 1738 3.3 0 5500 90 10000 P48WG-1205E2:1LF 9-18 60 1872 5 0 4000 92 6800 P48WG-1212E2:1LF 9-18 30 1915 12 0 1670 90 1000 P48WG-1215E2:1LF 9-18 30 1915 15 0 1330 90 680 P48WG-243R3E2:1LF 18-36 35 859 3.3 0 5500 91 10000 P48WG-2405E2:1LF 18-36 35 926 5 0 4000 93 6800 P48WG-2412E2:1LF 18-36 25 946 12 0 1670 91 1000 P48WG-2415E2:1LF 18-36 25 947 15 0 1330 91 680 P48WG-483R3E2:1LF 36-75 25 425 3.3 0 5500 91 10000 P48WG-4805E2:1LF 36-75 25 463 5 0 4000 93 6800 P48WG-4812E2:1LF 36-75 15 473 12 0 1670 91 1000 P48WG-4815E2:1LF 36-75 15 473 15 0 1330 91 680 DUAL OUTPUT P48WG-1212Z2:1LF 9-18 30 1937 ± 12 0 ± 835 89 ± 470 P48WG-1215Z2:1LF 9-18 30 1937 ± 15 0 ± 665 89 ± 330 P48WG-2412Z2:1LF 18-36 30 957 ± 12 0 ± 835 90 ± 470 P48WG-2415Z2:1LF 18-36 30 957 ± 15 0 ± 665 90 ± 330 P48WG-4812Z2:1LF 36-75 20 478 ± 12 0 ± 835 90 ± 470 P48WG-4815Z2:1LF 36-75 20 484 ± 15 0 ± 665 89 ± 330 If you need other specifications, please enquire. Notes:

PM8-Series – P48WG-xxxxE/Z2:1LF – Single and Dual O utput – 2”x1” - Metal Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 3/4 Package / Pinning / Derating PE AK Modelcode Datecode 50.80 (2.00) 10.16 (0.40) 5.08 (0.20) min. Bottom View 3 5 4 10.16 (0.40) 1 2 10.16 (0.40) 5.08 (0.20) 15.24 (0.60) 15.24 (0.60) 20.32 (0.80) 10.16 (0.40) 10.16 (0.40) 2.54 (0.10) 2.54 (0.10) 25.40 (1.00) Vin: Vout: Iout: Vin -Vout COM (if Dual) +Vout - + DIA. 1.00 (0.04) All dimensions are typical in millimeters (inches). - Pin diameter: 1.0 +/-0.05 (0.04 +/-0.002) - Pin pitch tolerance: +/-0.35 (+/-0.014) - Case tolerance +/-0.5 (+/-0.02) Specification may change without notice. 2" x 1" – METAL CASE # SINGLE DUAL 1 +Vin +Vin 2 - Vin - Vin 3 +Vout +Vout

4 Trim Common

6 Ctrl. Ctrl. PIN CONNECTIONS

PM8-Series – P48WG-xxxxE/Z2:1LF – Single and Dual O utput – 2”x1” - Metal Case Specification can change without a notice – We acce pt no liability for any inaccuracy or printing errors. Page 4/4 App Notes 1 = Measured Input reflected ripple current with a simulated source inductance of 12uH. 2 = Tested by minimal Vin and constant resistive load. 3 = One load is 25% to 100% load, the other load is 100% load, the output voltage variable rate is within ±5%. 4 = Tested by nominal Vin and 25% load step change (75% - 50% - 25% of Io) 5 = Input filter components (C1, L)are used to helpmeet conducted emissions requirent for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. 6 = An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5 - Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. Part # C1 L P48WG-12xx 330uF/100V 12uH P48WG-24xx 220uF/100V 12uH P48WG-48xx 220uF/100V 12uH EMC SPECIFICATIONS Radiated Emissions EN 55022 CLASS A Conducted Emissions 5 EN 55022 CLASS A ESD EN 61000-4-2 Perf. Criteria B RS EN 61000-4-3 Perf. Criteria A EFT 6 EN 61000-4-4 Perf. Criteria B Surge 6 EN 61000-4-5 Perf. Criteria B CS EN 61000-4-6 Perf. Criteria A PFMF EN 61000-4-8 Perf. Criteria A Over Voltage Protection (Zender diode clamp) 3.3 Vout: 3.9 V 5 Vout 6.2 V

12 Vout 15 V

15 Vout 18 V

± 12 Vout ± 15 V ± 15 Vout ± 18 V Under Voltage Lockout (typ.) 12 Vin Models Module ON/OFF 8.6V / 7.9V 24 Vin Models Module ON/OFF 17.8V / 16V 48 Vin Models Module ON/OFF 33.5V / 30.5V Remote ON/OFF Control ON: 3 -12 VDC or open circuit OFF: 0 – 1.2 VDC or Short circuit PIN2 and PIN6 OFF idle current: 5mA, typ. Notes: Rtrim-up Rtrim-down External Output Trimming Output can be externally trimmed. (Single output models only!)