P174FCT2273T PERICOM | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 4

Technical content

1 PS2013A 03/09/96

1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI74FCT273T (25WWWWW Series) P174FCT2273T Octal D Flip-Flop with Master Reset Product Description Pericom Semiconductor’s PI74FCT series of logic circuits are pro- duced in the Company’s advanced 0.6/0.8 micron CMOS technology, achieving industry leading speed grades. All PI74FCT2XXX devices have a built-in 25-ohm series resistor on all outputs to reduce noise because of reflections, thus eliminating the need for an external terminating resistor. The PI74FCT273T and PI74FCT2273T is an 8-bit wide octal designed with eight edge-triggered D-type flip-flops with individual D inputs and O outputs. The common buffered Clock (CP) and Master Reset (MR) load and resets (clear) all flip-flops simultaneously. The register is fully edge-triggered. The D input state, one setup time before the LOW-to-HIGH clock transition, is transferred to the corresponding flip-flop's O output. All outputs will be forced LOW independently of Clock or Data inputs by a LOW voltage level on the MR input. Device models available upon request. Fast CMOS Octal D Flip-Flop with Master Reset Logic Block Diagram Inputs Outputs Mode MR CP D N O N Reset (Clear) L X X L Load "1" H › hH Load "0" H › lL Truth Table(1) Pin Name Description MR Master Reset (Active LOW) CP Clock Pulse Input (Active Rising Edge) D 0-D7 Data Inputs O 0-O7 Data Outputs GND Ground V CC Power Product Pin DescriptionProduct Pin Configuration 1. H = High Voltage Level h = High Voltage Level one setup time prior to the LOW-to-HIGH Clock transition L = Low Voltage Level l = LOW Voltage Level one setup time prior to the LOW-to-HIGH Clock Transition X = Don’t Care › = LOW-to-HIGH Clock Transition 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI74FCT273T (25W(25W(25W(25W(25W Series) PI74FCT2273T Product Features

  • PI74FCT273/2273T is pin compatible with bipolar FAST™ Series at a higher speed and lower power consumption
  • 2 5 W series resistor on all outputs (FCT2XXX only)
  • TTL input and output levels
  • Low ground bounce outputs
  • Extremely low static power
  • Hysteresis on all inputs
  • Industrial operating temperature range: –40°C to +85°C
  • Packages available: – 20-pin 173 mil wide plastic TSSOP (L) – 20-pin 300 mil wide plastic DIP (P) – 20-pin 150 mil wide plastic QSOP (Q) – 20-pin 150 mil wide plastic TQSOP (R) – 20-pin 300 mil wide plastic SOIC (S) D R D D 0 O 0 CP CP MR Q D R D D 1 O 1 CP Q D R D D 2 O 2 CP Q D R D D 3 O 3 CP Q D R D D 4 O 4 CP Q D R D D 5 O 5 CP Q D R D D 6 O 6 CP Q D R D D 7 O 7 CP Q MR O 0 D 0 D 1 O 1 O 2 D 2 D 3 O 3 GND Vcc O 7 D 7 D 6 O 6 O 5 D 5 D 4 O 4 CP 20-PIN L20 P20 Q20 R20 S20

2 PS2013A 03/09/96

1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI74FCT273T (25WWWWW Series) P174FCT2273T Octal D Flip-Flop with Master Reset Supply Voltage to Ground Potential (Outputs & D/O Only) .. –0.5V to +7.0V Note: Stresses greater than those listed under MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other condi- tions above those indicated in the operational sec- tions of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. Parameters Description Test Conditions (1) Min. Typ (2) Max. Units V OH Output HIGH Voltage VCC = Min., VIN = VIH or VIL IOH = –15.0mA 2.4 3.0 V V OL Output LOW Current V CC = Min., VIN = VIH or VIL IOL = 64mA 0.3 0.55 V V OL Output LOW Current V CC = Min., VIN = VIH or VIL IOL = 12mA (25W Series) 0.3 0.50 V V IH Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 V V IL Input LOW Voltage Guaranteed Logic LOW Level 0.8 V IIH Input HIGH Current V CC = Max. V IN = VCC 1µ A IIL Input LOW Current V CC = Max. V IN = GND –1 µA IOZH High Impedance V CC = MAX .V OUT = 2.7V 1 µA IOZL Output Current V OUT = 0.5V –1 µA V IK Clamp Diode Voltage V CC = Min., IIN = –18mA –0.7 –1.2 V IOFF Power Down Disable V CC = GND, VOUT = 4.5V — — 100 µA IOS Short Circuit Current VCC = Max.(3), VOUT = GND –60 –120 mA V H Input Hysteresis 200 mV Capacitance (TA = 25°C, f = 1 MHz) Parameters(4) Description Test Conditions Typ Max. Units C IN Input Capacitance V IN = 0V 6 10 pF C OUT Output Capacitance V OUT = 0V 8 12 pF Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at Vcc = 5.0V, +25°C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second. 4. This parameter is determined by device characterization but is not production tested. Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested.)

3 PS2013A 03/09/96

1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI74FCT273T (25WWWWW Series) P174FCT2273T Octal D Flip-Flop with Master Reset Power Supply Characteristics Parameters Description Test Conditions (1) Min. Typ (2) Max. Units ICC Quiescent Power V CC = Max. V IN = GND or VCC 0.1 500 µA Supply Current DICC Supply Current per V CC = Max. V IN = 3.4V(3) 0.5 2.0 mA per Input @ TTL HIGH ICCD Supply Current per V CC = Max., Outputs Open V IN = VCC 0.15 0.25 mA/ Input per MHx(4) MR = Vcc, One Input Toggling VIN = GND MHz 50% Duty Cycle IC Total Power Supply V CC = Max., Outputs Open V IN = VCC 1.5 3.5 (5) mA Current(6) fCP = 10 MHZ, 50% Duty Cycle VIN = GND MR = Vcc, 50% Duty Cycle V IN = 3.4V 2.0 3.5 (5) One Bit toggling at fI = 5 MHZ V IN = GND V CC = Max., Outputs Open V IN = VCC 3.8 7.3 (5) fCP = 10 MHZ, 50% Duty Cycle VIN = GND MR = V CC , 50% Duty Cycle V IN = 3.4V Eight Bits toggling at V IN = GND 6.0 16.3 (5) fI = 2.5 MHZ, 50% Duty Cycle Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device. 2. Typical values are at Vcc = 5.0V, +25°C ambient. 3. Per TTL driven input (V IN = 3.4V); all other inputs at Vcc or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the Icc formula. These limits are guaranteed but not tested. 6. I C =IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + DICC DH N T + ICCD (fCP /2 + fIN I) ICC = Quiescent Current DICC = Power Supply Current for a TTL High Input (VIN = 3.4V) D H = Duty Cycle for TTL Inputs High N T = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fI = Input Frequency N I = Number of Inputs at fI All currents are in milliamps and all frequencies are in megahertz.

4 PS2013A 03/09/96

1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 1234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901 2123456789012 PI74FCT273T (25WWWWW Series) P174FCT2273T Octal D Flip-Flop with Master Reset Notes: 1. See test circuit and waveforms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 3. This parameter guaranteed but not production tested. Switching Characteristics over Operating Range 273T/2273T 273AT/2273AT 273CT/2273CT 273DT Com. Com. Com. Com. Parameters Description Conditions (1) Min Max Min Max Min Max Min Max Unit tPHL CP to ON R L = 500W tPLH MR to ON tSU Setup Time, HIGH or LOW 3.0 — 2.0 — 2.0 — 2.0 — ns Dn to CP t H Hold Time, HIGH or LOW 2.0 — 1.5 — 1.5 — 1.5 — ns Dn to CP tw CP Pulse Width HIGH or LOW tW MR Pulse Width(3) 7.0 — 6.0 — 6.0 — 3.0 — ns LOW tREM Recovery Time MR to CP(3) 4.0 — 2.0 — 2.0 — 2.0 — ns Pericom Semiconductor Corporation 2380 Bering Drive • San Jose, CA 95131 • 1-800-435-2336 • Fax (408) 435-1100 • http://www.pericom.com