OVPL5W3K TTELEC | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.3 06/08 Page 1 of 2 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com PCB with 3LEDs Optek Part No. OPA773 Viewing Angle Typical CCT Typical Luminous Flux (lm) @ 15V* 1 board 120° White 5750K 2 boards 100 3 boards 150 4 boards 200 5 boards 250 Power Line Designer Kit 0.5-Watt LED Modules OVPL5W3K Contents:
- Five (5) PCBs 8” in length
- Three (3) 0.5-Watt white LEDs per PCB, on-board regulator included
- Wire harness with connector
- Hand insertion tool Product Photo Here DO NOT LOOK DIRECTLY AT LED WITH UNSHIELDED EYES OR DAMAGE TO RETINA MAY OCCUR. RoHS 8.75” by 1.5”Ø tube *125mA per board stabilized The self-contained Power Line Designer Kit is a flexible and scalable lighting solution using mid-power LEDs to supply high luminous flux without additional heatsinking requirements. The kit includes components and instructions to allow a designer to configure LED placement as needed for uniform illumination in his application. With a 15-volt power supply (see Notes), the Power Line Kit is a total lighting solution.
Applications
- Architectural accent lighting
- Under-counter lighting
- Media illumination
- Lighting for large channel letters
- Backlighting for light boxes
- Point-of-sale displays Notes:
- All electrical and optical characteristics of the LEDs remain the same as specified in Optek Datasheet OVS5WBCR4.
- Maximum storage and operating temperature –40° ~ +100°C
- ESD threshold (HBM) 2000V
- 14-16V power supply not included. 1.0A minimum rating required, regulated or unregulated. 5 PCBs 8.00” x 0.425” wide (.062 FR4 material) 4’ Wire harness with connector Hand Insertion Tool OVPL5W3K OVPL5W3K
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. Issue A.3 06/08 Page 2 of 2 OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com OPA773 Dimensions Power Line Designer Kit OVPL5W3K Remove adhesive backing Place in desired position Attach 28-26 gauge wires with tool #9175 OPA773 14-16 VOLT DC INPUT 200mA min. per strip - BLACK WIRE + RED WIRE 0.425 [10.79] 8.000 [203.20] Optek Part Number Number of LEDs per Strip Number of Strips per Buss LED Drive Current per Strip AWG Supply Voltage OPA773 (included in kit) 3 1 to 5 125mA 26-28 14-16V OPA775 3 1 to 30 125mA 18 14-16V OPA776 3 2 to 60* 125mA 18 24V Optek Custom Assembly** Other Other Other Other Other Suggested Design Options 1. Install backplane (not included) behind panel to be illuminated. 2. Use masking tape (not included) to temporarily position the boards on backplane. 3. Route wire harness to each strip:
- Start with loose end and work to- ward 2.1mm jack.
- Use insertion tool to insert red and black wires on each board.
- Leave several inches of slack be- tween each strip. 4. Connect the 2.1mm jack to 14-16V power supply (not included, must be rated at 1.0A minimum). 5. Reposition all boards until optimal illumination is achieved. 6. Peel tape backing from boards. 7. Permanently apply boards to backplane. Note: Steps 6 and 7 are optional—do not peel off backing if the kit will be reused. Instructions *Multiples of 2 only **Contact Optek or an authorized distributor to discuss your application. 3.000 [76.20] - BLACK + RED WIRE Output connector 2.1mm ID/5.5mm OD Remove adhesive backing Place in desired position OPA773 14-16VOLT DC INPUT - BLACK + RED OPA773 OPA773 OPA773 OPA773 - BLACK + RED - BLACK + RED - BLACK + RED - BLACK + RED 14-16 VOLT DC INPUT 14-16 VOLT DC INPUT 14-16VOLT DC INPUT 14-16 VOLT DC INPUT Remove adhesive backing Place in desired position Remove adhesive backing Place in desired position Remove adhesive backing Place in desired position Remove adhesive backing Place in desired position OVPL5W3K OVPL5W3K