OVA5AB1AA-10M

OVA5AB1AA CONNOR-WINFIELD | Alldatasheet

Document overview

• Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
• PDF pages: 2

Technical content

THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. /WWW.CONWIN.COM PRODUCT DA T A SHEET Specifications subject to change without notice. DATA SHEET #: REV: DATE:PAGE OF Copyright 2001 Connor-Winfield all rights reserved.a CRYSTAL CONTROLLED OSCILLATORS The Connor-Winfield OVA5AB1AA is a hermetically sealed 14 Pin DIP, 5.0V Voltage Controlled Oven Stabilized Crystal Oscillator (OCVCXO) with a HCMOS / TTL compatible output. The OVA5AB1AA is designed for a higher stability Stratum 3 application requiring low jitter and tight frequency stability. 1 2 OVA5AB1AA - 10MHz OCXO SERIES CENTER FREQUENCY

FEATURES

DESCRIPTION

ORDERING INFORMATION

5.0V OPERATION LOW JITTER <3pS RMS FREQUENCY STABILITY: ±0.25ppm TEMPERATURE RANGE: 0 to 70°C FREQUENCY TOLERANCE OF ±4.6ppm OVER TWENTY YEARS HERMETICALLY SEALED 14 PIN DIP PACKAGE RoHS COMPLIANT / LEAD FREE 14 PIN DIP 5.0V STRATUM 3 HCMOS OCVCXO Cx099 00 06/13/06 OVA5AB1AA CW 0625 OVA5AB1AA 10MHz ABSOLUTE MAXIMUM RATINGS TABLE 1.0 PARAMETER UNITS MINIMUM NOMINAL MAXIMUM UNITS NOTE Storage Temperature -40 - 85 °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Control Voltage (Vc) -0.5 - 7.0 Vdc OPERATING SPECIFICATIONS TABLE 2.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Center Frequency (Fo) 10 - 20 MHz Frequency Calibration -1.5 1.5 ppm 1, 4 Frequency vs. change in Temperature -0.25 - 0.25 ppm 2 Frequency vs. change in Supply Voltage -0.05 - 0.05 ppm 3 Aging (Daily) -30 - 30 ppb 4 Total Frequency Tolerance -4.6 - 4.6 ppm 5 Operating Temperature Range 0 - 70 °C Supply Voltage (Vcc) 4.75 5.00 5.25 Vdc Supply Current (Icc) - - 300 mA Jitter (BW=10Hz to 20MHz) - - 3 ps rms Allan Variance (1 second) - 5.00E-10 - SSB Phase Noise at 10Hz offset - -90 - dBc/Hz SSB Phase Noise at 10KHz offset - -150 - dBc/Hz Start Up Time: Oscillator - - 10 mS Warm Up Time - - 5 Minutes 6 TDEV @ 1.0 Sec. - - 1 ns TDEV @ 4.0 Sec. - - 2 ns INPUT CHARACTERISTICS TABLE 3.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE Control Voltage Range (Vc) 0.5 2.18 4.1 Vdc Frequency at Vc=0.5 Vdc -30 - -18 ppm 7 Frequency at Vc=4.1 Vdc 18 - 30 ppm 7 Slope of Frequency Adjust 10.0 - - ppm/V Input Impedance 100k - - Ohm HCMOS OUTPUT CHARACTERISTICS TABLE 4.0 PARAMETER MINIMUM NOMINAL MAXIMUM UNITS NOTE LOAD 12 15 18 pf Voltage (High) (Voh) 4.5 - - Vdc (Low) (Vol) - - 0.4 Vdc Current (High) (Ioh) -4 - mA (Low) (Ioh) - - 4 mA Duty Cycle at 50% of Vcc 45 50 55 % Rise / Fall Time 10% to 90% - - 6 ns PACKAGE CHARACTERISTICS TABLE 5.0 Package 14 pin DIP, hermetically sealed, grounded case, welded package Notes: 1) Initial calibration @ 25°C, Vc=2.18V. 2) Frequency stability, 0 to 70°C, peak to peak. 3) Frequency stability per 5% change in supply voltage. 4) At the time of shipment after 48 hours of operation. 5) Inclusive of operating temperature range, supply voltage change, load change, shock and vibration, 20 years aging, Vc=2.18V, initial calibration. 6) Measured @ 25°C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency, measured after 30 minutes of continuous operation at a stable 25°C 7) Referenced to Fo @ 25°C, Positive Transfer Characteristic.

THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722. /WWW.CONWIN.COM PRODUCT DA T A SHEET Specifications subject to change without notice. DATA SHEET #: REV: DATE:PAGE OF Copyright 2001 Connor-Winfield all rights reserved.a CRYSTAL CONTROLLED OSCILLATORS 2 2Cx099 00 06/13/06 CONTROL VOLTAGE CONTROL VOLTAGE 120°C 150°C 180°C 260°C 220°C 360 Sec. Max. 120 S Max. 10 S 60 S Max. Time Temperature 260°C WAVE SOLDER PROFILE ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 300 cycles, 30 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No Bubbles in flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 2003. 8 hour steam age prior to 245°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board- mount product, 260°C ±5°C for 20 seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15 minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition F. 1500G’s, 0.5ms, half sine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C.