OPN1600-8C2 MRV | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 2
Technical content
Features
WDM & Optical Transport Not sure what solution best fi ts your needs? Visit www.mrv.com or e-mail us at sales@mrv.com Datasheet
Rev.2 08-08 Copyright ©2008 MRV Communications, Inc. All Rights Reserved. Product Description OPN1600-8C2 8 x 10/100/1000 Base Tx and 2 x XFP ports Ethernet Switch module for LD1600, long slot module OPN1600-8S2 8 x GE, SFO based and 2 x 10 XFP ports Ethernet Switch module for LD1600, long slot module OPN800-8C2 8 x 10/100/1000 Base Tx and 2 x XFP ports Ethernet Switch module for LD800, dual short slot module Operating Temperature -5 to 45o C Storage Temperature -10 to 70o C Relative Humidity 85% maximum, non-condensing Weight OCM1600: 1.200 kg (2.64 lb) OCM800 : 0.7 kg (1.5 lb)OCM800 : 0.7 kg (1.5 lb) Connectors LAN: 8 fi xed 10/100/1000Base-T ports LAN/WAN: 2x 10Gbps - XFP ports Management: Ethernet 10/100Base - TX port for TELNET, SSH, and/or SNMP out-of-band connection EnvironmentalOrder Info WDM & Optical Transport Traffi c Management The OPN800/1600-8C2 module supports full CoS and QoS (MEF 14 model) including fl ow classifi cation, rate limiting, shaping, WFQ scheduling, and strict priority scheduling. For network convergence applications with a clear boundary between the customer’s network and the carrier’s network, CoS layers (802.1p, IP ToS & MPLS EXP bits) can be mapped/marked to preserve priorities or mapped into protection profi les preset by the carrier. Dynamic QoS provides for sharing/borrowing bandwidths allocated for real-time or high priority applications at intervals, when these services are on standby. This capability optimizes bandwidth utilization at the access/demarcation point of the network without the need for involving the aggregation layer for this purpose. Ethernet Loop-backs The OPN800/1600-8C2 module offers remote loop-back functionality on a physical interface or a specifi c VLAN that traverses UNI or NNI interfaces. The loop-back function allows for remote troubleshooting services, from NOC or any other manageable location without having to physically visit the customer premises. The Loop-back functionality is hardware controlled to provide performance monitoring and SLA verifi cation at wire speed. Virtual Cable Diagnostics The OPN800/1600-8C2 module’s Virtual Cable Diagnostics feature enables the administrator to test electrical data cables attached to its ports for a physical fault, to identify the fault type, and to pinpoint its location. Optical Performance Level Monitoring (Digital Diagnostics) The digital diagnostics feature of the OPN800/1600-8C2 modules XFPs (as per the standard SFF-8472) provides access to a number of real-time operating parameters such as optical TX/RX power, voltage and temperature, as well as component information, such as vendor code, serial number, and wavelength. The information provided using digital diagnostics, together with alarm and warning thresholds, enables the network administrator to identify potential problems in optical transmission and take preemptive action before any service outage actually occurs. Link Fault Refl ection/Propagation A fault detected at a network interface will be propagated to the user interface and will trigger a “link down” state on it. This feature enables the user’s network to re-converge to an alternative path when necessary. The feature is confi gurable and operates on LOS detection. Sniffer VLAN Enables the operator to defi ne a “Sniffer” function that captures data and forwards it to a defi ned VLAN for analysis. The sniffi ng can be set for specifi c VLANs, Layer 2-3-4 fi elds in a packet, MAC addresses etc. and conforms to the requirements of Law Enforcement Monitoring. Power consumption 28 Watt Full wire speed Support on all ports Technical Specifi cations