OPIA800 TTELEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 20

Technical content

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 1 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Description: The OPIA800 through OPID804 optocouplers are designed for applications that utilize a digital output (Phototlogic®) in a dual-in-line package. Isolation voltage from 2,500 to 5,000 Volts RMS product are designed for some of the most stringent power system isolation requirements. Theory of operation: The LED transmitter is used to illuminate the Photosensor providing electrical isolation between two power systems while maintaining the ability to transmit information from one power system to the other. In many applications, analog or digital signals may be required to be transmitted between two power systems while maintaining isolation between the power systems up to 5,000 volts RMS. A variety of LED and photosensor configurations are available depending on the system requirements The ratio Current Transfer Ratio (CTR) is determined using the output current and input current for analog photosensors. CTR ratios can range from as low as 5 to over 9,000 depending on the device. All DIP product is shipped in a shipping tube with “TU” identified on the end of the part number. Example: OPIA800DTU is a 8-Pin DIP shipped in a tube (TU). Features:

  • 2,500 or 5,000 Vrms electrical isolation
  • Choice of a Single and Dual LED
  • Choice of Phototransistor or Photologic® Sensor
  • Low-cost plastic Dual-In-Line (DIP) package Agency Approvals:
  • UL Certification No: E58730
  • VDE NO: 40026713, 40026624 RoHS Applications:
  • High voltage isolation
  • PCBoard power system isolation
  • Industrial equipment power isolation
  • Medical equipment power isolation
  • Office equipment 200100*10 20 ==− −= mA mA CurrentLED CurrentrPhotosensoCTR Moisture

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 2 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Analog Output Devices Ordering Information Part Number Isolation Voltage Max. (Vrms) CTR Min/Typ/Max Typ. Tplh / Tphl (ns) [RL = ohms] Package Configuration OPIA800 2,500 300 / 1,600 / - 7 / 2 [ 2.2 K] 8 Pin DIP A K—K A B C E (Dar) OPIA801 2,500 500 / 1,600 / - 10 / 5 [ 4.7 K] 8 Pin DIP A K—K A B C E (Dar) OPIA802 2,500 15 / 43 / - 0.3 / 0.3 [ 1.9 K] 8 Pin DIP A K—K A C E OPIA803 2,500 5 / 43 / - 0.4 / 0.3 [ 4.1 K] 8 Pin DIP A K—K A C E Digital Output Devices Ordering Information Part Number Isolation Voltage Max. (Vrms) Typ. Tr / Tf (ns) [RL = 350 ohms] Typ. Tplh / Tphl (ns) [RL = ohms] Package Configuration OPID804 5,000 30 / 30 45 / 45 [ 350] 8 Pin DIP A K—NAND Configuration: Definition of Terms LED Identification—Sens or Identification LED A = Anode K = Cathode 10K Logic 10K Inverted Logic NAND Gate NAND Gate K = Cathode A = Anode B = Base C = Collector E = Emitter Packaging Part Number Suffix: D = DIP, TU = Ship in Tubes, TR = Ship on Tape and Reel Example: OPID606DTR Sensor Part Number Pin # 1 2 3 4 5 6 7 8 OPIA800 A K E C C-B K-C OPIA801 A K E C C-B K-C OPIA802 A K E C A-B K OPIA803 A K E C A-B K OPID804 A K GND Output Enable Vcc Package Outline Dimensions and Schematics: Top-View Symbol Definition A Anode B Base C Collector E Emitter K Cathode OPID804 OPIA802 OPIA803 OPIA800 OPIA801 DIMENSIONS ARE IN: INCHES [MILLIMETERS] TOLERANCE: ± 0.008 INCHES [± 0.2 MILLIMETERS]

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 3 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature -55° C to +125° C Operating Temperature OPIA800 OPIA801 OPIA802 OPIA803 OPID804 -40° C to +115° C 0° C to +125 ° C -55° C to +115° C -55° C to +100° C 0° C to +85° C Isolation voltage (1 minute) OPID804 OPIA800, OPIA801, OPIA802, OPIA803 5,000 Vrms 2,500 Vrms Lead Soldering Temperature (1/16” (1.6 mm) from case for 5 seconds with soldering iron) 260° C Input Diode Continuous Forward Current OPIA802, OPIA803, OPID804 OPIA800 OPIA801 25 mA 20 mA Peak Forward current (1 µs pulse width, 300 pps) OPIA800, OPIA801, OPIA802, OPIA803 OPID804 1 A 40 mA Reverse Voltage OPIA800, OPIA801, OPIA802, OPIA803, OPID804 5 V Power Dissipation OPIA802, OPIA803, OPID804 OPIA800, OPIA801 45 mW 35 mW Absolute Maximum Ratings (TA = 0° C to 70° C unless otherwise specified) Output IC Vcc—Collector-Emitter Voltage OPIA800 OPIA801 OPIA802, OPIA803 -0.5 V to +7 V -0.5 V to +18 V -0.5 V to +15 V Collector Current OPIA802, OPIA803 OPIA800, OPIA801 8 mA 60 mA Power Dissipation OPIA800, OPIA801, OPIA802, OPIA803 100 mW Output NAND Gate—OPID804 Vcc—Supply voltage 7 V Enable voltage 5.5 V High Level Output voltage 7 V Low Level Output current 50 mA Output Collector Power Dissipation 85 mW

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 4 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 5 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Switching Characteristics: OPIA800 *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 6 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 OPIA800 Characteristic Curves

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 7 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 OPIA800 Characteristic Curves

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 8 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 *6 Current transfer ratio is a ratio of input current and output current expressed in %. *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) (TA = 25°C)

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 9 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Switching Characteristics: OPIA801 *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *8 Test Circuit Propagation Delay Time *10 Test Circuit for Instantaneous Common Mode Rejection Voltage

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 10 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 2.4mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8) (TA = 0 to +70°C unless otherwise specified)

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 11 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Switching Characteristics: OPIA802 *8 RL = 1.9k ohms is equivalent to on LSTTL and 5.6k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. (TA = 25°C, VCC=5V, IF=16mA) *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 12 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 (TA = 0 to +70°C unless otherwise specified) *5 Current transfer ratio is a ratio of input current and output current expressed in %. *6 Io = 1.1mA *7 Measured as 2-pin element (Short 1,2,3,4 and 5,6,7,8)

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 13 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Switching Characteristics: OPIA803 (TA = 25°C, VCC=5V, IF=16mA) *8 RL = 4.1k ohms is equivalent to on LSTTL and 6.1k ohm pull-up resistor. *9 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (1) level (Vo>2.0V). *10 Instantaneous common mode rejection voltage “output(1)” represents a common voltage variation that can hold the output above (0) level (Vo>0.8V). *11 Bandwidth represents a point where AC input goes down by 3dB. *9 Test Circuit Propagation Delay Time *11 Test Circuit for Instantaneous Common Mode Rejection Voltage

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 14 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode VF Forward Voltage (*4) - 1.6 1.8 V I F = 10 mA, TA = 25° C BVR Reverse Breakdown Voltage 5 - - V I R = 10 µA, TA = 25° C CIN Input Capacitance - 60 - pf V F = 0.0 V, f = 1M Hz Output Photologic VOL Low Level Output Voltage - 0.4 0.6 V IOL = 13 mA, VCC = 5.5 V, IF = 5 mA, VEH=2V IOH High Level Output Current - 2 250 µA VCC=5.5 V, VO=5.5 V, VE=2.0 V, IF=250 µA IEH High Level Enable Current - -0.8 - mA V CC = 5.5 V, VE = 2.0 V IEL Low Level Enable Current -2.0 -1.2 - mA V CC = 5.5 V, VE = 2.0 V ICCL Low Level Output Current - 13 18 mA V CC = 5.5 V, VE = 0.5 V, IF = 10 mA ICCH High Level Output Current - 7 15 mA V CC = 5.5 V, VE = 0.5 V, IF = 0 mA II-O Leakage Current - - 1.0 mA VI-O = 3,000 V, TA = 25° C, t = 5 s, RH = 45% tEHL Enable Propagation delay “High to Low” (*8) - 15 - ns VEH = 3.0 V, VEL = 0.5 V, RL = 350 Ω , IF = 7.5 mA, CLOAD = 15 pf tELH Enable Propagation delay “Low to High” (*8) - 40 - IFHL / IFLH Hysteresis - 0.8 - Ratio VCC = 5 V, RL = 280 Ω RI-O Input-Output Isolat ion resistance (*5) - 1012 - ohm V I-O = 500 V, TA = 25° C CI-O Input-Output Capacit ance (*5) - 0.6 - pf f = 1M Hz, T A = 25° C tPHL & tPLH Propagation delay “High to Low” and “Low to High” (*7) - 45 75 ns VCC = 5 V, RL = 350 Ω , IF = 7.5 mA, CLOAD = 15 pf, TA = 25°C tR & tF Rise and Fall Time - 30 - CMH Instantaneous common mode rejection voltage “High Output” (*9) - 500 - V/us VCM = 10 V, RL = 350 Ω , IF = 0 mA, VO = 2.0 V CML Instantaneous common mode rejection voltage “Low Output” (*9) - -500 - VCM = 10 V, RL = 350 Ω , IF = 5 mA, VO = 0.8 V (TA = 0 to +70°C unless otherwise specified) Notes: (Typical values are all at VCC = 5V, Ta = 25°C. *5 Measured as 2-Pin element. Connect pins 2 and 3, connect pins 5,6,7 and 8. *6 DC current transfer ratio is defined as the ratio of output collector current to forward bias input current. *7 Refer to Figure 1. *8 Refer to Figure 2. *9 CMH represents a common mode voltage ignorable rise time ratio that can hold logic (1) state in output. CML represents a common mode voltage ignorable fall time ratio that can hold logic (0) state in output.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 15 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Recommended Operating Conditions: OPIA804 Truth Table Circuit Block Diagram Test Circuit Propagation Delay Time Figure 1.

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 17 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 OPID804 Characteristic Curves

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 18 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 OPID804 Characteristic Curves

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 19 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Quality / Reliability Requirements Note: This is to be performed when a change occurs to form, fit or function. Government and Industry Standard Compliance Requirements European Union’s Reduction of Hazardous Substances (RoHS) Directive 2002/95/EC Parameter Failure Criteria Conditions HTRB D IC(OFF) ± 10% 11 samples after 500Hrs 0 Fail @ VCE = 5.0VDC, Ta = 70°C HTFB D IC(ON) ± 10% 50 samples after 96Hrs

0 Fail @ Max P D, Ta = 25°C

MTTF @ 90% confidence 150, 000 Min. @ 25°C, 25mADC Moisture Sensitivity Level MSL 1 per JDEC stnd J-STD-020B Lead Solderability 0 Fail per Method 208 of MIL-STD-202. Glass Transition of body 125° C Min. DSC test method Temperature Humidity-Bias ± 20% 85°C, 85%RH, 500Hrs, 80% min Iceo Temperature Cycle ± 20% per Method 1010.7 of MIL-STD-883E High Temperature Storage ± 20% 85°C, 500Hrs Autoclave 0 Fail T A = 121°C, Pressure = 15psi, Humidity = 100%, Time = 96Hrs Label Identification DESCRIPTION: Size: 3” (7.4 cm) X 2.2” (5.5 cm) Lettering shall be black on white background. Format shall be as: Notes: 1. The DATE CODE is a 4-digit code for date of manufacture where YY is the last two digits of the year, and WW is week number of manufacture. 2. The LOT I.D. is the manufacturing location lot identification where Y is the year of manufacture, NNNN is a sequential lot identifier, and DDD is the day of the year of manufacture. – or use equivalent label format. Carrollton, TX, USA MADE IN TAIWAN OPTEK P/N __OPIA800D-TU__ IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII IIIIIIIIIIIIIIIIIIIII

OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 3 23-2396 sensors@optekinc.com www.optekinc.com Issue A.5 02/2010 Page 20 of 20 OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible. OPIA800—OPIA803, OPID804 Packaging Information: Tube Packaging Specifications (TU): Quantity: 8-pin: 48pcs/tube DIMENSIONS ARE IN: INCHES [MILLIMETERS] TOLERANCE: ± 0.008 INCHES [± 0.2 MILLIMETERS] Optek's Optocoupler Part Numbers Packaging Quantities Tube Inner Small Carton Medium Carton Large Carton Qty Weight 52 x 7 x 7.5 Qty Weight Qty Weight Gross Weight Qty Weight Gross Weight Qty Weight Gross Weig ht P/H and SMD 4-PIN OPIA400D/A, OPIA410D/A - OPIA413D/A 6-PIN 8-PIN M/F SOP 4-PIN and 5-PIN OPIA401B - OPIA404B, OPIA414B, OPIA500B SSOP 4-PIN OPIA405C - OPIA409C 170 -- 10,200 -- P/H = Pin-Hole Packages (Referred as D = Dual-In-Line Package) SMD = Standard Surface Mount Packages (Referred as A = 6.5mil SMD) M/F or SOP = Mini-Flat Packages or Small Outside Packages (Referred as B = 4.40mil SMD w/ 2.54mil Lead- Spacing) SSOP = Shrink SOP Packages (Referred as C = 3.60mil SMD with 1.27mil Lead-Spacing)