OPI110 TTELEC | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 3

Technical content

Optically Coupled Isolator OPI110, OPI1264 Series © TT electronics plc Issue C 11/2017 Page 1 TT Electronics | OPTEK Technology

1645 Wallace Drive, Carrollton, TX 75006|Ph: +1 972 323 2200

www.ttelectronics.com | sensors@ttelectronics.com General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. Description: Each Optoisolator in this data sheet contains an infrared Light Emitting Diode (LED) and a NPN silicon Photosensor. The OPI110 and OPI1264 devices have 890 nm Light Emitting Diode (LED) and NPN phototransistor sensor. The devices are sealed in a precast opaque housing with a optically transmissive path between the LED and the photosensor. The Optoisolators in this data sheet are UL recognised under E58730. This series is designed for transmission of information between one power supply voltage and another where the potentials during surge conditions are not greater than the guaranteed isolation voltage. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Applications:  High voltage isolation between input and output  Electrical isolation in dirty environments  Industrial equipment  Medical equipment Features:  15 kV electrical isolation  Choice of phototransistor  Low-cost plastic housing  UL recognized File No. E58730

Ordering Information

(,000) CTR Min / Max IF (mA) Typ / Max VCE (Volts) Max Lead Length / Spacing OPI110 890 nm Transistor 12.5 / NA 30 0.50" / 0.55" OPI110A 25 / NA OPI110B 50 / 125 OPI110C 100 / NA OPI1264 Transistor 12.5 / NA OPI1264A 25 / NA OPI1264B 50 / 125 OPI1264C 100 / NA

Optically Coupled Isolator OPI110, OPI1264 Series © TT electronics plc Issue C 11/2017 Page 2 TT Electronics | OPTEK Technology www.ttelectronics.com | sensors@ttelectronics.com General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. Absolute Maximum Ratings (TA = 25o C unless otherwise noted) Storage Temperature -40° C to +100° C Operating Temperature -40° C to +85° C Input-to-Output Isolation Voltage(1)(2) ± 15 kVDC Lead Soldering Temperature (1/16” (1.6 mm) from case for 5 seconds with soldering iron)(3) 260° C Input Diode Forward DC Current 40 mA Reverse DC Voltage 2 V Power Dissipation(4) 50 mW Output Photosensor Collector-Emitter Voltage OPI110, OPI1264 Emitter-Collector Voltage 5 Power Dissipation(5) 100 mW Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. (2) UL recognition is for 15kV dc for one minute. (3) RMA flux is recommended. The duration can be extended to 10 seconds maximum when flow soldering. (4) Derate linearly 0.83 mW/°C above 25°C. (5) Derate linearly 1.67 mW/°C above 25°C. OPI1264 1 4 2 3 OPI110 1 4 2 3

Optically Coupled Isolator OPI110, OPI1264 Series © TT electronics plc Issue C 11/2017 Page 3 TT Electronics | OPTEK Technology www.ttelectronics.com | sensors@ttelectronics.com General Note TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics’ own data and is considered accurate at time of going to print. Notes: (1) Measured with input and output leads shorted. Typical input/output capacitance is 0.06 pF. Electrical Characteristics (TA = 25o C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS TEST CONDITIONS Input Diode (See OP265 for additional information - for reference only) VF Forward Voltage - - 1.6 V IF = 20 mA IR Reverse Current - - 100 µA VR = 2 V Output Photosensor (See OP505 for additional information - for reference only) V(BR)CEO Collector-Emitter Breakdown Voltage OPI110, OPI1264 V IC = 100 µA V(BR)ECO Emitter-Collector Breakdown Voltage OPI110 OPI1264 V IE = 100 µA, IF = 0 IE = 100 µA ICEO Collector-Emitter Dark Current OPI110, OPI1264 100 nA VCE = 15 V, EE = 0 Coupled IC(ON) Coupled “ON” Current OPI110, OPI1264 1.25 - 44 mA IF = 10mA VCE = 5V IC/IF DC Current Transfer Ratio OPI110, OPI1264 OPI110A, OPI1264A OPI110B, OPI1264B OPI110C, OPI1264C 12.5 25.0 50.0 100.0 125 IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V IF = 10 mA, VCE = 5 V VCE(SAT) Collector Saturation Voltage OPI110, OPI1264 0.4 V IF = 10 mA, IC = 1.6 mA ICEO Collector-Emitter Dark Current OPI110, OPI1264 200 nA VCE = 20 V, IF = 0 VISO Isolation Voltage 15 - - kVDC See Note 1.