NHSW046AT NICHIA | Alldatasheet

Document overview

  • Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
  • PDF pages: 13

Technical content

-0- No. STSE-CC6141A <Cat.No.061226> SPECIFICATIONS FOR NICHIA CHIP TYPE WHITE LED MODEL : NHSW046AT NICHIA CORPORATION

-1- Nichia STSE-CC6141A <Cat.No.061226> 1.SPECIFICATIONS ( 1 ) A b s o l u t e M a x i m u m R a t i n g s ( T a = 2 5 ° C ) Item Symbol Absolute Maximum Rating Unit Forward Current I F 10 mA Pulse Forward Current I FP 3 0 m A Allowable Reverse Current I R 8 5 m A Power Dissipation P D 3 2 m W Operating Temperature T opr -40 ~ +100 °C Storage Temperature T stg -40 ~ +100 °C Soldering Temperature T sld Reflow Soldering : 260°C for 10sec. Dip Soldering : 260°C for 10sec. Hand Soldering : 350°C for 3sec. I FP Conditions : Pulse Width 10msec. and Duty 1/10 ( 2 ) I n i t i a l E l e c t r i c a l / O p t i c a l C h a r a c t e r i s t i c s ( T a = 2 5 ° C ) Item Symbol Condition Typ. Max. Unit Forward V oltage VF IF=5[mA] (2.9) 3.2 V Luminous Intensity Iv I F=5[mA] (270) - mcd x - IF=5[mA] 0.31 - - Chromaticity Coordinate y - IF=5[mA] 0.32 - - ½ Please refer to CIE 1931 chromaticity diagram. ( 3 ) R a n k i n g ( T a = 2 5 ° C ) Item Symbol Condition Min. Max. Unit Rank V Iv I F=5[mA] 360 500 mcd Rank U Iv I F=5[mA] 250 360 mcd Luminous Intensity Rank T Iv I F=5[mA] 180 250 mcd ½ Luminous Intensity Measurement allowance is ± 10%. C o l o r R a n k s ( I F=5mA,Ta=25°C) Rank a0 Rank b1 Rank b2 Rank c0 y 0.276 0.295 0.339 0.318 y 0.318 0.360 0.385 0.351 ½ Color Coordinates Measurement allowance is ± 0.01. ½ One delivery will include up to two consecutive color ranks and three luminous intensity ranks of the products. The quantity-ratio of the ranks is decided by Nichia. 2.INITIAL OPTICAL/ELECTR ICAL CHARACTERISTICS Please refer to figure’s page. <= <=

-2- Nichia STSE-CC6141A <Cat.No.061226> 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure’s page. M a t e r i a l a s f o l l o w s ; Package : Heat-Resistant Polymer Encapsulating Resin : Epoxy Resin (with Diffused + Phosphor) E l e c t r o d e s : Ag Plating Copper Alloy 4.PACKAGING

  • The LEDs are packed in cardboard boxes after taping. Please refer to figure’s page. The label on the minimum packing unit show s ; Part Number, Lot Number, Ranking, Quantity
  • In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation.
  • The LEDs may be damaged if the boxes are dr opped or receive a strong impact against them, so precautions must be taken to prevent any damage.
  • The boxes are not water resistant and therefor e must be kept away from water and moisture.
  • When the LEDs are transported, we recommend th at you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; { - Year ( 6 for 2006, 7 for 2007 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., B for Nov. ) ¯¯¯¯ - Nichia's Product Number U - Ranking by Color Coordinates „ - Ranking by Luminous Intensity

-3- Nichia STSE-CC6141A <Cat.No.061226> 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Standard Test Method Test Conditions Note Number of Damaged Resistance to Soldering Heat (Dip Soldering) JEITA ED-4701 300 301 Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) 1 time 0/22 Solderability (Dip Soldering) JEITA ED-4701 300 303 Tsld=235 ± 5°C, 2sec. (using flux) 1 time over 95% Resistance to Soldering Heat (Reflow Soldering) JEITA ED-4701 300 301 Tsld=260°C, 10sec. (Pre treatment 30°C,70%,168hrs.) 2 times 0/22 Solderability (Reflow Soldering) JEITA ED-4701 300 303 Tsld=215 ± 5°C, 3sec. (using flux, Lead Solder) 1 time over 95% Thermal Shock JEITA ED-4701 300 307 - 4 0 ° C ~ 1 0 0 ° C 1min. (10sec.) 1min. (Pre treatment 30°C,70%,168hrs.) 100 cycles 0/100 Temperature Cycle JEITA ED-4701 100 105 30min. 5min. 30min. 5min. 100 cycles 0/100 Moisture Resistance Cyclic JEITA ED-4701 200 203 90%RH 24hrs./1cycle 10 cycles 0/100 High Temperature Storage JEITA ED-4701 200 201 Ta=100°C 1000 hrs. 0/100 Temperature Humidity Storage JEITA ED-4701 100 103 Ta=60°C, RH=90% 1000 hrs. 0/100 Low Temperature Storage JEITA ED-4701 200 202 Ta=-40°C 1000 hrs. 0/100 Steady State Operating Life Ta=25°C, I F=10mA 1000 hrs. 0/100 Steady State Operating Life of High Temperature ½½ Ta=85°C, I F=5mA 1000 hrs. 0/100 Steady State Operating Life of High Humidity Heat ½½ 60°C, RH=90%, I F=5mA 1000 hrs. 0/100 Steady State Operating Life of Low Temperature ½½ Ta=-40°C, I F=5mA 1000 hrs. 0/100 Permanence of Marking JEITA ED-4701 500 501 Solvent : Isopropyl Alcohol Solvent Temperature : 20 ~ 25°C Dipping Time : 5 min. 1 time 0/22 Vibration JEITA ED-4701 400 403 100 ~ 2000 ~ 100Hz Sweep 4min. 200m/s 2 3directions, 4cycles 48min. 0/10 Drop 75cm 3 times 0/10 Electrostatic Discharge JEITA ED-4701 300 304 R=1.5k Ω, C=100pF Test V oltage=2kV 3 times Negative/Positive (2) CRITERIA FOR JUDGING DAMAGE Criteria for Judgement Item Symbol Test Conditions Min. Max. Forward V oltage V F I F=5mA - U.S.L.*) ¯ 1.1 Luminous Intensity Condition 1 IV I F=5mA L.S.L.) ¯ 0.7 - Luminous Intensity Condition 2 ½½ IV I F=5mA L.S.L.) ¯ 0.5 - ½½ These test items are judged by the criteria of Luminous Intensity Condition 2.

-4- Nichia STSE-CC6141A <Cat.No.061226> 7.CAUTIONS The LEDs are devices which are materialized by combining Blue LEDs and special phosphors. Consequently, the color of the LEDs is changed a little by an operating current. Care should be taken after due consideration when using LEDs. (1) Moisture Proof Package

  • When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that th is can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package.
  • The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage
  • Storage Conditions Before opening the package : The LEDs should be kept at 30°C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30°C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again.
  • If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be perf ormed using the following conditions. Baking treatment : more than 24 hours at 65 ± 5°C
  • Nichia LED electrodes are silver plated coppe r alloy. The silver surface may be affected by environments which contain corrosive substan ces. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible.
  • Please avoid rapid transitions in ambient temperat ure, especially in high humidity environments where condensation can occur. (3) Heat Generation
  • Thermal design of the end product is of paramount importance. Pl ease consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification.
  • The operating current should be decided after considering the ambient maximum temperature of LEDs.

-5- Nichia STSE-CC6141A <Cat.No.061226> (4) Soldering Conditions

  • The LEDs can be soldered in place using the reflow soldering method and the dip soldering method.
  • Recommended soldering conditions Reflow Soldering Dip Soldering Hand Soldering Lead Solder Lead-free Solder Pre-heat Pre-heat time Peak temperature Soldering time Condition 120 ~ 150°C 120 sec. Max. 240°C Max. 10 sec. Max. refer to Temperature - profile 180 ~ 200°C 120 sec. Max. 260°C Max. 10 sec. Max. refer to Temperature - profile (N2 reflow is recommended.) Pre-heat Pre-heat time Solder bath temperature Dipping time 100°C Max. 60 sec. Max. 260°C Max. 10 sec. Max. Temperature Soldering time 350°C Max. 3 sec. Max. (one time only) ½ Although the recommended soldering conditions are specified in the above table, reflow, dip or hand soldering at the lowest possible temperature is desirable for the LEDs. ½ A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the conditions shown to the under figure. [Recommended soldering pad design] Use the following conditions shown in the figure.
  • Occasionally there is a brightness decrease caus ed by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method.
  • Repairing should not be done af ter the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing.
  • Reflow soldering should not be done more than two times.
  • Dip soldering s hould not be done more than one time.
  • When soldering, do not put stress on the LEDs during heating.
  • After soldering, do no t warp the circuit board. 60sec.Max. Above 220°C 120sec.Max. Pre-heating 260°C Max. 10sec. Max. 1~ 5°C / sec. 1~ 5°C / sec. 180 ~ 200°C <1 : Lead Solder> <2 : Lead-free Solder> 60sec.Max. Above 200°C 120sec.Max. Pre-heating 240°C Max. 10sec. Max. 2.5 ~ 5°C / sec. 2.5 ~ 5°C / sec. 120 ~ 150°C (Unit : mm) 4 4 9.2 0.8 0.8 : Solder resist

-6- Nichia STSE-CC6141A <Cat.No.061226> (5) Cleaning

  • It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be us ed to clean the LEDs because of worldwide regulations.
  • Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. (6) Static Electricity
  • Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti- electrostatic glove be used when handling the LEDs.
  • All devices, equipment and machinery must be properly grounded. It is r ecommended that precautions be taken against surge voltage to the equipment that mounts the LEDs.
  • When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by st atic electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended).
  • Damaged LEDs will show some unusual characteris tics such as the forward voltage becomes lower, or the LEDs do not light at the low current. C r i t e r i a : ( VF > 2.0V at I F=0.5mA) (7) Others
  • NHSW046A complies with RoHS Directive.
  • The LED light output is strong enough to injure hum an eyes. Precautions must be taken to prevent looking directly at the LEDs with unaid ed eyes for more than a few seconds.
  • Flashing lights have been known to cause disc omfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it.
  • The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia’s sales staff in advance for info rmation on the applications in which exceptional quality and reliability are required, pa rticularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices).
  • User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis.
  • The formal specifications must be exchanged and signed by both parties before large volume purchase begins.
  • The appearance and specificatio ns of the product may be modified for improvement without notice.

0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 480 620 550 540 530 520 580 570 560 600 610 590 630 470 460 490 510 500 x y ICI Chromaticity Diagram -7- ½ Color Coordinates Measurement allowance is ± 0.01. Nichia STSE-CC6141A <Cat.No.061226>

Allowable Forward Current IF(mA) Relative Luminosity (a.u.)Relative Luminosity (a.u.) Forward Current IFP (mA) Allowable Forward Current IFP(mA) „ Ambient Temperature vs. Allowable Forward Current Ambient Temperature Ta (°C) „ Ambient Temperature vs. Relative Luminosity Ambient Temperature Ta (°C) „ Ambient Temperature vs. Forward Voltage Ambient Temperature Ta (°C) Forward Voltage VF(V) Duty Ratio (%) „ Forward Current vs. Relative Luminosity Forward Current IFP(mA) Forward Voltage VF (V) „ Forward Voltage vs. Forward Current „ Duty Ratio vs. Allowable Forward Current Ta=25°C Ta=25°C Ta=25°C IFP=5mAIFP=5mA 100 15.0 12.5 10.0 7.5 5.0 2.5 60 80 1204002 0 1 0 0 100 3.6 3.4 3.2 2.8 2.6 2.4 3.0 03 0 6 0 9 0 1 2 0-60 -30 01 0 2 0 4 0 30 5.0 3.0 1.0 2.0 4.0 03 0 6 0 9 0 1 2 0-60 -30 2.0 1.0 0.5 0.2 Nichia STSE-CC6141A <Cat.No.061226> CHARACTERISTICS Model NHSW046A NICHIA CORPORATION Title No. 061213659071 -8-

0°C 25°C 50°C 100°C -40°C Relative Luminosity (a.u.) „ Ambient Temperature vs. Chromaticity Coordinate „ Directivity „ Spectrum„ Forward Current vs. Chromaticity Coordinate Radiation Angle x Relative Emission Intensity (a.u.) y Wavelength λ (nm) Ta=25°C IFP=5mA Ta=25°C IF=5mA 1.0 0.5 x y 0° 10° 20° 30° 40° 50° 60° 70° 80° Ta=25°C IFP=5mA Y-Y X-X XX Y Y 0.35 0.34 0.33 0.31 0.30 0.32 0.35 0.33 0.30 0.34 0.32 0.31 350 450 550 750 650 1.2 1.0 0.8 0.4 0.2 0.6 Nichia STSE-CC6141A <Cat.No.061226> CHARACTERISTICS Model NHSW046A NICHIA CORPORATION Title No. 061213659081 -9-

½ NHSW046x has a protection device built in as a protection circuit against static electricity. ITEM MATERIALS PACKAGE Heat-Resistant Polymer ENCAPSULATING RESIN Epoxy Resin (with Diffused + Phosphor) ELECTRODES Ag Plating Copper Alloy Cathode mark (C 0.25) (1.55) 2.2 (1.15) 1.4 Anode Cathode Internal Circuit A K Protection device (1.4)0.4 0.4 (0.7) 1.3 0.9 (0.7) Unit mm Allow NICHIA CORPORATION No. OUTLINE DIMENSIONS 061205537022 Title Model NHSW046x ±0.1 Scale -10- Nichia STSE-CC6141A <Cat.No.061226>

Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Nichia STSE-CC6141A <Cat.No.061226> -11- Unit mm NICHIA CORPORATION No. TAPING DIMENSIONS 051212548071 Title Model NHSx046AT Allow Scale XXXX LED TYPE NHSx046AT LOT XXXXXX-U„ QTY pcs Taping part Reel End of tape Label Reel part No LEDs Top cover tape Reel Lead Min.160mm (No LEDs) Pull direction LEDs mounting part No LEDs Reel Lead Min.400mm Embossed carrier tape Reel Lead Min.100mm (No LEDs) 1.75±0.1 4±0.1 4±0.1 2±0.05 3.5±0.05 (2.75) φ 60+1-0 11.4±1 9±0.3 φ 13±0.2 φ 21 ±0.8 1.48±0.1 φ 180+0 φ 1+0.2 8+0.3 -0 . 1 φ 1.5+0.1 0.25±0.05 1.51±0.1 2.4±0.1 Cathode mark 3,000pcs/Reel

The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. L a b e l Packing unit Reel/bag Quantity/bag (pcs) Moisture proof foil bag 1reel 3,000 MAX. Cardboard box Dimensions (mm) Reel/box Quantity/box (pcs) Cardboard box S 291 ¯237¯120¯8t 7reel MAX. 21,000 MAX. Cardboard box M 259 ¯247¯243¯5t 15reel MAX. 45,000 MAX. Cardboard box L 444 ¯262¯259¯8t 30reel MAX. 90,000 MAX. The box is partitioned with the cardboard. Seal Moisture proof foil bag Nichia LED Reel Moisture absorbent material Label XXXX LED TYPE NHSx046xT LOT xxxxxx- U„ Q T Y P C S NICHIA CORPORATION

491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN

-12- NICHIA CORPORATION No. PACKING 051220546072 Title Model NHSx046xT Nichia STSE-CC6141A <Cat.No.061226>