N152 IVO | Alldatasheet
Document overview
- Manufacturer or author: Provided By ALLDATASHEET.COM(FREE DATASHEET DOWNLOAD SITE)
- PDF pages: 4
Technical content
Features
Motive spindle position display – Absolute multiturn measuring system – Display: LCD backlit, two lines – Actual value and target display – Hollow shaft max. ø14 mm – Interface RS485 – Resolution: 1440 steps/revolution ±4096 revolutions – Two operating keys for format alignment touch by – touch Technical data - electrical ratings Voltage supply 24 VDC ±10 % Current consumption ≤40 mA Display LCD, 7-segment display, 2-lines, backlit Measuring principle Absolute multiturn measuring system Steps per turn 1440 Number of turns 4096 / 12 bit Spindle pitch ≤14 mm Interface RS485 (ASCII protocol) Data memory Parameter buffer: EEPROM Current value buffer: >10 years by integrated 3 V lithium battery Programmable parameters Display position horizontal/ vertical Measuring unit mm/inch Spindle pitch Counting direction Spindle tolerance Positioning direction Direction arrows Tolerance window Round up/down Motive positioning Two softkeys for format alignment Direct motor connection to N 152 by motor cable Standard DIN EN 61010-1 Protection class II Overvoltage category II Pollution degree 2 Emitted interference DIN EN 61000-6-3 Interference immunity DIN EN 61000-6-2 Approval UL/cUL N 152 Technical data - mechanical design Hollow shaft ø14 mm Operating speed ≤600 rpm (short-term) Protection DIN EN 60529 IP 65 Operating temperature -10...+50 °C Storing temperature -20...+70 °C Relative humidity 80 % non-condensing Torque support Torque pin provided at housing E-connection - Cable output (15 cm) with male connector M8, 4-pin - Motor cable with female connector M16, 12-pin Operation / keypad Membrane with two keys Housing type Surface-mount with hollow shaft Dimensions W x H x L 37 x 75 x 45 mm Mounting Surface-mount with hollow shaft Weight approx. 120 g Material Polyamide black, UL 94V-0 Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 2 Subject to modification in technic and design. Errors and omissions excepted.11/11/2008 N 152 Part number N 152. 1 3 A 01 Hollow shaft A Hollow shaft ø14 mm Display A Inclined B Horizontal at front Voltage supply 3 24 VDC E-connection 1 Cable output M8, motor cable 0.5 m 2 Cable output M8, motor cable 1.5 m Interface
1 RS485
Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 Accessories Connectors and cables Z 178.A01 Adaptor cable between cable connector M8 and female M16, 1 m Z 178.AW1 Cable connector M8, 4-pin, less cable with integrated terminating resistor 120 Ω Z 178.B01 Mating connector M8, 4-pin, less cable Z 178.D05 Data and supply cable M8, Master to N 150 and N 155, 5 m Z 178.S01 Cable connector M8, 4-pin, less cable Z 178.V01 Coupling cable 1 m between M8 and M8 Z 178.Y01 Y-junction M8, 4-pin, with cable multiconDrive represents a simplified and very efficient, reasonably priced system for automatic format alignment. With multiconDrive the spindle position displays communi- cate directly with EC motors. Every spindle position display is connected to the corresponding motor by a separate cable output providing the motor without delay with the signals “clockwise”, “counterclockwise”, “rotation speed” for switchover to high/low speed. The spindle position display provides two keys for clock- wise and counterclockwise direction used during the first editing operation. The key makes the motor moving into the requested direction. A soft touch results in a defined STEP. Thus, new spindle positions can be edited under direct visual check of the operator with an accuracy of ±1/100 mm. Shaft position parameters once set can be filed as profile in the control. The serial interface enables network of maxi- mum 32 spindle position displays with PC or PLC. For com- plete solutions N 242 memory controller as operating and memory terminal is available. Up to 100 format profiles can be stored by teach-in. The respective position parameters can be retransmitted at any time as target to the respecitve spindle position displays to release automatic format align- ment cycles.
Description
www.baumerivo.com Spindle Position Displays N 152 Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 24 V 0 V IN 1 output IN 1 input IN 2 output IN 2 input (logic 24 V) OUT 1 IN 1 (left) IN 2 (right) IN 4 (speed) 24 V n.c. n.c. AI- (0...10 V) AI+ (0...10 V) OUT 3 (fault) IN 3 (speed) 0 V A B C D E F G H J K L M supply voltage Error SPAMotor Motor left Motor right Speed n.c. n.c. n.c. n.c. n.c. Error signal Speed GND release counter- clockwise Enable n.c. release clockwise M Circuit diagram SPA – connector, 4-pin M8 connector Assignment Pin 1 Tx/Rx–, RS485 Pin 2 Tx/Rx+, RS485 Pin 3 Sensor supply +24 V Pin 4 Sensor supply 0 V M8 connector Motor connector, 12-pin Connector Assignment Pin A – Pin B Motor left Pin C Motor right Pin D Speed Pin E – Pin F – Pin G – Pin H – Pin J – Pin K Error signal Pin L Speed Pin M GND AB D C E F G H J K M L M16 male connector Terminal assignment
www.baumerivo.com www.baumerivo.com Spindle Position Displays www.baumerivo.com 4 Subject to modification in technic and design. Errors and omissions excepted.11/11/2008 N 152 Hollow shaft max. ø14 mm, automatic format alignment Display LCD two lines, interface RS485 Dimensions 20.5 6.5 30.15 31.8 12.5 ø14H7 ø20 75° 4.8 ø6h9 0.5x 45° 2:1 M8 male connector Pin M4 Optional display position Torque pin Seal M16 male connector / motor